warning lights MERCEDES-BENZ CLS 2014 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2014, Model line: CLS, Model: MERCEDES-BENZ CLS 2014Pages: 382, PDF Size: 4.7 MB
Page 118 of 382
Useful information
iThis Operator's Manual describes all
models and all standard and optional
equipment of your vehicle available at the
time of publication of the Operator's
Manual. Country-specific differences are
possible. Please notethat your vehicle may
not be equipped with all features
described. This also applies to safety-
related systemsand functions.
iRead the information on qualified
specialist workshops: (Ypage 26).
Exterior lighting
Generalnotes
For reasonsofsafety, Mercedes-Benz
recommends that you drive with the lights
switched on even during the daytime.
Therefore, your vehicle is equipped with
special daytime running lamps. In some
countries, operation of the headlamps varies
due to legal requirements and self-imposed
obligations.
If you wish to drive during the daytime without
lights, switchoff the daytime running lamps
function in the on-board computer
(Ypage 230).
Driving abroad
Symmetrical low-beam headlamps
Switchthe headlamps to symmetrical low
beam in countries in which traffic drives on
the opposite side of the road from the country
where the vehicle is registered. This prevents
glare to oncoming traffic. When using
symmetrical lights, the edge of the road is not
lit as widely and as far ahead as normal.
Have the headlamps converted ataqualified
specialist workshop as close to the border as
possible before drivinginthesecountries.
Asymmetrical low beam
Have the headlamps converted back to
asymmetrical low-beam headlamps at a
qualified specialist workshop as soon as
possible after crossing the border again.
Setting the exterior lighting
Setting options
Exterior lightingcan be set using:
Rthe light switch
Rthe combination switch(Ypage 119)
Rthe on-board computer (Ypage 230)
Light switch
Operation
Left-handstanding lamps
\nRight-hand standing lamps
Parkinglamps, licenseplate and
instrumentclusterlighting
\rAutomatic headlamp mode,
controlled by the light sensor
Low-beam/high-beam headlamps
If you hearawarningtonewhen you leave the
vehicle, the lightsmay still be switched on.
XTurn the light switchto \r.
116Exterior lighting
Light sa nd windshield wipers
Page 119 of 382
The exterior lighting (except the parking/
standinglamps) switches off automatically if
you:
Rremove the SmartKey from the ignition lock
Ropen the driver's door with the SmartKey
in position0.
Automatic headlampmode
GWARNING
When the light switch is set to \r,the low-
beam headlamps may not be switched on
automatically if there is fog, snow or other
causes of poor visibility due to the weather
conditions such as spray. There isarisk of an
accident.
In such situations, turn the light switch to
.
The automatic headlamp feature is only an
aid. The driver is responsible for the vehicle's
lighting at all times.
Left-hand standinglamps
\nRight-hand standinglamps
Parking lamps, license plate and
instrument cluster lighting
\rAutomatic headlamp mode,
controlled by the light sensor
Low-beam/high-beam headlamps
\ris the favored light switch setting. The
light setting is automatically selected
accordingtothe brightness of the ambient
light (exception: poor visibility due to weather
conditions such as fog, snow or spray):
RSmartKey in position1in the ignition lock:
the parking lamps are switched on or off
automatically depending on the brightness
of the ambient light.
RWith the engine running: if you have
activated the daytime runninglamps
function via the on-board computer,the
daytime runninglamps or the low-beam
headlamps and parking lamps are switched
on or off automatically depending on the
brightness of the ambient light.
XTo switch on automatic headlamp
mode:turn the light switch to \r.
Only for Canada:
The daytime runninglamps improve the
visibility of your vehicle during the day. The
daytime runninglamps function is required by
law in Canada. It cannot therefore be
deactivated.
When the engine is runningand the vehicle is
stationary: if you move the selector lever from
adrive position toP,the daytime running
lamps/low-beam headlamps go out after
three minutes.
When the engine is running, the vehicle is
stationary and in high ambient light: if you
turn the light switch to ,the daytime
runninglamps and parking lamps switch on.
If the engine is runningand you turn the light
switch to ,the manual settings take
precedenceover the daytime runninglamps.
USA only:
The daytime runninglamps improve the
visibility of your vehicle during the day. To do
this, the daytime runninglamps function must
be switched on using the on-board computer
(Ypage 230).
If the engine is runningand you turn the light
switch to or ,the manual settings
Exterior lighting117
Lights and windshield wipers
Z
Page 120 of 382
take precedence overthe daytime running
lamps.
Low-beam headlamps
GWARNING
When the lightswitchisset to \r,thelow-
beam headlampsmay not be switchedon
automatically if there is fog, snow or other
causes of poor visibility due to theweather
conditions such as spray. Thereisarisk of an
accident.
In such situations, turnthe light switch to
.
Left-hand standing lamps
\nRight-hand standing lamps
Parking lamps, license plate and
instrumentcluster lighting
\rAutomatic headlamp mode,
controlled by the light sensor
Low-beam/high-beam headlamps
Even if the light sensor does not detect that
it is dark,the parking lamps and low-beam
headlamps switchonwhen the ignition is
switched on and the light switchisset to the
position. This isaparticularly useful
function in the eventofrain and fog.
XTo switch on thelow-beam headlamps:
turnthe SmartKey in the ignition lock to
position2or start the engine.
XTurn the light switchto .
The green indicator lamp in the
instrumentcluster lightsup.
Parking lamps
!If the battery has been excessively
discharged, the parking lamps or standing
lamps are automatically switched off to
enable the nextengine start. Alwayspark
your vehiclesafelyand sufficiently lit
according to legalstandards.Avoid the
continuoususe of the parking lamps
for severalhours.Ifpossible, switch on the
\nright or the left standinglamp.
Left-hand standinglamps
\nRight-hand standinglamps
Parking lamps, license plate and
instrument cluster lighting
\rAutomatic headlamp mode,
controlled by the light sensor
Low-beam/high-beam headlamps
XTo switch on:turn the light switch to
.
The green indicator lamp in the
instrument cluster lights up.
118Exterior lighting
Lights and windshiel dw ipers
Page 122 of 382
The blue indicator lamp in the
instrument cluster lights up when the high-
beam headlamps are switched on.
XTo switch off the high-beam
headlamps:move the combination switch
back to its normal position.
The blue indicator lamp in the
instrument cluster goes out.
iVehicles with Adaptive Highbeam Assist:
when Adaptive Highbeam Assist is active,
it controls activation of the high-beam
headlamps (Ypage 121).
High-beam flasher
High-beam headlamps
Turn signal, right
$High-beam flasher
!Turn signal, left
XTo switch on:turn the SmartKey in the
ignition lock to position1or2,orstart the
engine.
XPull the combination switch in the direction
of arrow $.
Hazard warning lamps
XTo switch on the hazard warning lamps:
press button .
All turn signals flash. If you now switch on
aturn signal using the combination switch,
only the turn signal lamp on the
corresponding side of the vehicle will flash.
XTo switch off the hazard warning
lamps:press button .
The hazard warning lamps automatically
switch on if:
Ran air bag is deployed
Rthe vehicle decelerates rapidly from a
speed of more than 45 mph (70 km/h) and
comes toastandstill
The hazard warning lamps switch off
automatically if the vehicle reachesaspeed
of over6mph (10 km/h) again afterafull
brake application.
iThe hazard warning lamps still operate if
the ignition is switched off.
Headlampcleaning system
The headlamps are cleaned automatically if
the "Wipe with washer fluid" function is
operated five times (Ypage 125)while the
lightsare on and the engineisrunning. When
you switchoff the ignition, the automatic
headlamp cleaning systemisreset and
counting is resumed from 0.
120Exterior lighting
Lights and windshield wipers
Page 123 of 382
Cornering lightfunction
The cornering light function improves the
illumination of the road overawideanglein
the direction you are turning, enabling better
visibility in tight bends, for example. It can
only be activated whenthe low-beam
headlamps are switched on.
Active:
Rif you are driving at speeds below 25 mph
(40 km/h)and switch on the turn signal or
turn the steering wheel
Rif you are driving at speeds between
25 mph(40km/h)and 45 mph(70km/h)
and turn the steering wheel
Not active:if you are driving at speeds above
25 mph (40 km/h) or switch off the turn
signalorturn the steering wheel to the
straight-ahead position.
The cornering lamp may remain lit forashort
time, but is automatically switched off after
no more than three minutes.
Active light function
The active light function isasystem that
moves the headlamps according to the
steering movements of the front wheels.In
this way, relevant areasremain illuminated
while driving. Thisallowsyou to identify
pedestrians, cyclists and animals.
Active:whenthe lights are switched on.
Adaptive Highbeam Assist
Important safety notes
GWARNING
Adaptive Highbeam Assist does not recognize
road users:
Rwho have no lights, e.g. pedestrians
Rwho have poor lighting, e.g. cyclists
Rwhose lighting is blocked, e.g. byabarrier
In very rare cases, Adaptive Highbeam Assist
may fail too recognize other road users that
have lights, or may recognize them too late.
In this or similar situations, the automatic
high-beam headlamps will not be deactivated
or activated regardless. There isarisk of an
accident.
Always carefully observe the traffic conditions
and switch off the high-beam headlamps in
good time.
Exterior lighting121
Lights and windshield wipers
Z
Page 126 of 382
The interior lighting automatically switches
on if you:
Runlock the vehicle
Ropenadoor
Rremove the SmartKey from the ignition lock
The interior light is activated forashort while
when the SmartKey is removed from the
ignition lock. You can activatethis delayed
switch-off using the on-board computer
(Ypage 232).
Manualinterior lighting control
Frontoverhead control panel
To switch the rear interior lighting
on/off.
To switch the automatic interior
lighting control on/off
$ To switch the right-hand reading
lamp on/off
! \rTo switch the frontinterior lighting
on/off
To switch the left-hand reading lamp
on/off
XTo switch the front interior lighting on/
off:press the \rbutton.
XTo switch the rear interior lighting on/
off:press the button.
XTo switch the reading lampson/off:
press the button.
Crash-responsive emergency lighting
The interior lighting is activated automatically
if the vehicle is involved in an accident.
XTo switch off the crash-responsive
emergency lighting:press the hazard
warning lamp button.
or
XLock and then unlock the vehicle using the
SmartKey.
Replacing bulbs
Important safety notes
Xenon bulbs
GDANGER
Xenon bulbs carryahigh voltage. You can get
an electric shock if you remove the cover of
the Xenon bulb and touch the electrical
contacts. There isarisk of fatal injury.
Never touch the parts or the electrical
contacts of the Xenon bulb. Always have work
on the Xenon bulbs carried out ataqualified
specialist workshop.
Bulbs and lamps are an importantaspect of
vehicle safety. You must therefore make sure
that these function correctly at all times.
Have the headlamp setting checked regularly.
LED lamps
You can neither replace Xenon bulbsnor LED
bulbs. Have LED bulbschanged ataqualified
specialist workshop.
Bulbs and lamps are an important aspect of
vehicle safety. You must therefore make sure
that these function correctly at all times.
Have the headlamp setting checked regularly.
Other bulbs
GWARNING
Bulbs, lamps and connectors can get very hot
when operating. If you changeabulb, you
124Replacing bulbs
Lights and windshield wipers
Page 144 of 382
XTurn the SmartKey to position0in the
ignition lock or remove it (Ypage 147).
XTo activate:press the button.
The indicator lamp in the button lights
up.
iIf the residual heat function is activated,
the windows may fog up on the inside.
iThe blower will run atalow speed
regardless of the airflow setting.
iIf you activatethe residual heat function
at high temperatures, only the ventilation
will be activated. The blower runs at
medium speed.
XTo deactivate:press the button.
The indicator lamp in the button goes
out.
Residualheat is deactivated automatically:
Rafter approximately 30 minutes
Rwhen the ignition is switched on
Rif the battery voltage drops
Setting the air vents
Important safety notes
GWARNING
Very hot or very cold air can flow from the air
vents. This could result in burns or frostbite in
the immediate vicinityofthe air vents. There
isarisk of injury.
Make sure that all vehicle occupantsalways
maintainasufficient distancetothe air
outlets. If necessary, redirect the airflow to
another area of the vehicle interior.
In order to ensure the direct flow of fresh air
through the air ventsinto the vehicle interior,
please observe the following notes:
Rkeep the air inlet between the windshield
and the hood free of blockages, such as ice,
snow or leaves.
Rnever cover the air ventsorair intakegrilles
in the vehicle interior.
Setting the center air vents
Center air vent,left
Center air vent,right
$Center vent thumbwheel, right
!Center vent thumbwheel, left
XTo open/close:turn thumbwheels $
and !up or down.
Setting the side air vents
Defroster vent
Side air vent
$Control for side air vent
XTo open/close:turn thumbwheel $up or
down.
Setting the glove box air vent
!Close the air vent when heating the
vehicle.
At high outside temperatures, open the air
vent and activatethe "cooling with air
142Setting the air vents
Climate control
Page 171 of 382
Parking brake
GWARNING
If you must brake the vehicle with the parking
brake, the braking distance is considerably
longer and the wheels could lock. There is an
increased danger of skidding and accidents.
Only use the parking brake to brake the
vehicle when the service brake is faulty. Do
not apply the parking brake too firmly. If the
wheels lock, release the parking brake until
the wheels begin turningagain.
GWARNING
If you leave children unsupervised in the
vehicle, they could set it in motion by, for
example:
Rreleasing the parking brake
Rshifting the automatic transmission out of
the parking positionP
Rstartingthe engine.
They could also operate the vehicle's
equipment. There isarisk of an accident and
injury.
When leaving the vehicle, always take the
SmartKey with you and lock the vehicle. Never
leave children unsupervised in the vehicle.
If you brake the vehicle with the parking
brake, the brake lamps will not light up.
XTo apply:depress parking brake firmly.
When the engine is running, the (USA
only) or (Canada only) indicator lamp
lights up in the instrumentcluster.
XTo release:depressthe brakepedal and
keep it depressed.
XPull release handle .
When the ignition is switched on or the
engine is running, the (USA only) or
(Canada only) indicator lamp goes out
in the instrumentcluster.
Parking thevehicle foralong period
If you leave thevehicle parked for longer than
four weeks, thebattery may be damagedby
exhaustive discharging.
If you leave thevehicle parked for longer than
six weeks, thevehicle may suffer damage as
aresult of lack of use.
XVisitaqualifiedspecialist workshop and
seek advice.
iYou can obtain informationabout trickle
chargers fromaqualifiedspecialist
workshop.
Driving tips
General notes
Important safety notes
GWARNING
If you switch off theignitionwhile driving,
safety-relevant functions are only available
with limitations, or not at all. This could affect,
for example, the power steering and the brake
boosting effect.You will require considerably
more effort to steer and brake. There isarisk
of an accident.
Do not switch off the ignition while driving.
GWARNING
If you operate mobile communication
equipment while driving, you will be
Driving tips169
Driving and parking
Z
Page 175 of 382
Servicing the brakes
!If the red brake warning lamp lights up in
the instrumentcluster and you hear a
warningtonewhile the engine is running,
the brakefluid level may be too low.
Observe additional warningmessages in
the multifunction display.
The brakefluid level may be too low due to
brakepad wear or leakingbrakelines.
Have the brakesystem checked
immediately. This work should be carried
out ataqualified specialist workshop.
!Vehicles with 4MATIC:function or
performancetests may only be carried out
ona2-axle dynamometer. If you are
planning to have the vehicle tested on such
adynamometer, contactanauthorized
Mercedes-BenzCenter to obtain further
information first. Otherwise, you could
damage the drive train or the brakesystem.
!Vehicles with 4MATIC:as the ESP®
system operates automatically, the engine
and the ignition must be switched off
(SmartKey in position0or1in the ignition
lock or Start/Stop button in position0or
1)while the parking brakeisbeing tested
onabrakedynamometer.
Brakingmaneuvers triggeredautomatically
by ESP®may seriouslydamagethebrake
system.
!Vehicles with 4MATIC:as theESP®
system operatesautomatically, theengine
and theignition system must be switched
off (SmartKey in position0or1in the
ignition lockorStart/Stopbuttonin
position0or1)when:
Rtesting theparking brakeonabrake
dynamometer.
Ryou intendtohave thevehicletowed with
oneoftheaxlesraised.
Braking maneuvers triggered automatically
by ESP®may seriouslydamagethebrake
system.
All checksand maintenance work on the
brakesystem must be carried out at a
qualified specialist workshop. Consult a
qualified specialist workshoptoarrangethis.
Havebrakepads installed and brakefluid
replacedataqualified specialist workshop.
If thebrakesystem has only been subject to
moderateloads,you should test the
functionalityofyour brakes at regular
intervals. To do so, press firmly on thebrake
pedal when driving atahigh speed. This
improvesthegripofthebrakepads.
You can findadescription of Brake Assist
(BAS) on (Ypage 67)orofBASPLUSon
(Ypage 67).
The braking characteristics of thevehiclecan
be seriouslyimpaired if:
Rbrakepads other than those recommended
are installed
Rtherecommended brakefluid is notused
Safe braking can no longer be guaranteed.
AMG high-performance and ceramic
brakes
The high-performance brake system is
installed only on the CLS 63 AMG.
The AMG brake systems are designed for
heavy loads. This may lead to noise when
braking. This will depend on:
RSpeed
RBraking force
REnvironmental conditions, such as
temperature and humidity
The wear of individualcomponentsofthe
brake system, such as the brake pads/linings
or brake discs, depends on the individual
driving style and operating conditions.
For this reason, it is impossibletostate a
mileage that will be valid under all
circumstances. An aggressive driving style
will lead to high wear. You can obtain further
information aboutthis from your authorized
Mercedes-BenzCenter.
Driving tips173
Driving and parking
Z
Page 192 of 382
If indicator lamp is not lit:
XPress the button.
Indicator lamp lights up. The vehicle
heightisadjusted to raised level.
TheVehicle Risingmessage appears in
the display.
The "Raised level" setting is canceled if you:
Rdrive ataspeed over approximately
75 mph (120 km/h)
Rdrive for approximately three minutes at a
speed over 50 mph (80 km/h)
The "Raised level" remains active when you
are not driving within these speed ranges.
Setting the normal level
XStart the engine.
If indicator lamp is lit:
XPress the button.
Indicator lamp goes out. The vehicle is
adjusted to normal level.
Suspension tuning
General notes
The electronically controlled damping system
works continuously. This improves driving
safety and ride comfort.
The damping is tuned individually to each
wheel and depends on:
Ryour driving style, e.g. sporty
Rthe road surface condition, e.g. bumps
Ryour individualselection, i.e. sports or
comfort
Your selection remains stored even if you
remove the SmartKey from the ignition lock.
Sports tuning
The firmer suspension tuning in Sport mode
ensures even better contact with the road.
Select this mode when employingasporty
driving style, e.g. on winding country roads.
XPress button .
Indicator lamp lights up. Sports
suspension tuning is selected.
TheAIRMATIC SPORTmessage appears in
the multifunction display.
Comfort tuning
In comfort mode, the driving characteristics
of your vehicle are more comfortable.
Therefore, select this mode if you favor a
more comfortable driving style. Select
comfort mode also when driving fast on
straight roads, e.g. on straight stretches of
freeway.
XPress button .
Indicator lamp $lights up. Comfort tuning
is selected.
TheAIRMATIC COMFORTmessage appears
in the multifunction display.
AMG adaptive sport suspension
system
Important safety notes
GWARNING
When the vehicle is being lowered, people
could become trapped if their limbs are
between the vehicle body and the wheels or
190Driving systems
Driving and parking