steering wheel MERCEDES-BENZ CLS-Class 2007 W219 Comand Manual

42 Audio
Radio operation
Press the number buttons in
succession:=, >, and ?.
Each number entered appears in the
display.
The system tunes to the frequency en-
tered (in this example: 98.5 Mhz) and
switches back to the FM menu.Tuning via station search
Seven channels are available on the
Weather Band.
On COMAND control unit
Switch to the WB waveband by press-
ing the
WB soft key in the Radio main
menu (
page 37).
The system will tune to the strongest
receivable station.
Press + or,.
Search begins in ascending or
descending frequency.
The search stops at the next receivable
station.On multifunction steering wheel
Switch the multifunction display in the
instrument cluster to Radio display
(
page 25).
Pressj ork.
The search stops at the next receivable
station.
Tuning via station presets
The seven strongest channels are sorted in
p r e s t 1 t o 7 e a c h t i m e y o u p r e s s t h e
WB s o f t
key. They are accessed using the number
keypad.
Press one of the number keys
! - @.
The system tunes to the station stored
under this number.
i
Entries outside the frequency range are
not possible.
Within the AM waveband, the input is
restricted to frequencies within the re-
spective frequency increment, which
is10 kHz.
The system will select the nearest valid
frequency if a frequency outside the
frequency increment is entered.
Tuning to a station on Weather Band

48 Audio
Single CD operation
On the multifunction steering wheel
Switch the multifunction display in the
instrument cluster to the Single CD dis-
play (
page 25).
Pressj for forward skipping.
or
Pressk for backward skipping.Selecting via track list
The track list contains all tracks of the cur-
rent CD. Only one list entry is visible at a
time, it is the track currently playing.
Use% or & to select another track
from the list.
Press', or wait approx. 3 seconds
without changing the selection.
The selected track is played.Selecting via manual entry of the track
number
Open the Single CD main menu
(
page 46).
Press..
The Manual track input display ap-
pears. The number of tracks on the CD
is displayed.
i
Forward skipping:
The next track is played.
Backward skipping:
The system skips back to the beginning
of the track if more than approx. 10
seconds playing time of the track cur-
rently playing have elapsed.
The system skips back to the beginning
of the previous track if less than 10
seconds playing time of the track cur-
rently playing have elapsed.

57 Audio
MP3 operation
Press'.
The COMAND changes the folder and
loads the data from the new folder.
It may take a while to load the data, de-
pending on the number of folders and
tracks.
You may select a track in the current fold-
er.
The following options are available:
Selecting via manual entry of the track
number (
page 58)
Selecting via scan search (page 58)
Selecting via track skip
Selecting via track listSelecting via track skip
On the COMAND control unit
Open the MP3 main menu (page 55).
Press+0for forward skipping.
or
Press, for backward skipping.
On the multifunction steering wheel
Switch the multifunction display in the
instrument cluster to the audio display
(
page 25).
Pressj for forward skipping.
or
Pressk for backward skipping.Selecting via track list
The track list contains all tracks in the cur-
rent folder. Only one track can be viewed
at a time.
Selecting a track
i
Forward skipping:
The next track is played.
i
Backward skipping:
The system skips back to the beginning
of the track if more than approx. 10
seconds playing time of the track cur-
rently playing have elapsed.
The system skips back to the beginning
of the previous track if less than 10
seconds playing time of the track cur-
rently playing have elapsed.

69 Audio
CD changer* operation
The following options are available:
Selecting via track skip
Selecting via track list (page 69)
Selecting via manual entry of the track
number (
page 69)
Selecting via scan search (page 70)
Selecting via track skip
On the COMAND control unit
Open the CD changer main menu
(
page 66).
Press+0for forward skipping.
or
Press, for backward skipping.
On the multifunction steering wheel
Switch the multifunction display in the
instrument cluster to the CD changer
display (
page 25).
Pressj for forward skipping.
or
Pressk for backward skipping.
Selecting via track list
The track list contains all tracks of the cur-
rent CD. Only one list entry is visible at a
time, it is the track currently playing.
Use% or & to select another track
from the list.
Press' or wait approx. 3 seconds
without changing the selection.
The selected track is played.
Selecting via manual entry of the track
number
Open the CD changer main menu
(
page 66).
Press..
The Manual track input display ap-
pears. The number of tracks on the CD
is displayed.
Selecting a track
i
Forward skipping:
The next track is played.
Backward skipping:
The system skips back to the beginning
of the track if more than approx. 10
seconds playing time of the track cur-
rently playing have elapsed.
The system skips back to the beginning
of the previous track if less than 10
seconds playing time of the track cur-
rently playing have elapsed.


79 Satellite radio*
Satellite radio operation
Tuning using the multifunction steering
wheel
Switch the multifunction display in the
instrument cluster to Satellite radio
display (
page 25).
Pressk.
The search proceeds in ascending or-
der.
or
Pressj.
The search proceeds in descending or-
der and stops at the first receivable
station. Tuning via scan search
Scan search is characterized as follows:
Scan search plays a channel for
approx. 8 seconds and then skips to
the next channel within the current
category.
Scan search can be ended manually.
Scan search stops automatically at the
station that was playing when scan
search was started.
Press the Scan soft key.
The scan search starts.
Press the Scan soft key again.
The scan search ends.Additional text information (artist and title)
related to the current broadcast can be
displayed.
Press the Info soft key.
i
Using% o r&0i s f o l l o w e d b y a s h o r t
delay before the change occurs. Using
+ a n d, changes the channel
immediately.
Obtaining additional text
information

83 Telephone*
Important notes
Always drive with extreme caution
when operating the telephone hands-
free.
For safety reasons, the cellular phone
handset should not be used to place or
receive a call while driving.
If the signal is very weak (display in the
status bar):
Wait until reception improves before
placing a call.
Close the windows and reduce all ex-
ternal noise as much as possible when
using hands-free operation.
Make sure that the air vents are not
pointed in the direction of the micro-
phones located in the overhead control
panel near the rear view mirror. Adjust
air vents and/or reduce blower speed
if necessary.
Tips on telephone operation
i
Once the cellular phone is inserted into
the telephone cradle, it can be operat-
ed:
using the cellular phone itself,
using the COMAND control unit,
using the multifunction steering
wheel, or
using the voice control system*.
Descriptions in this Operator’s Manual
presume that the cellular phone is in-
serted into the telephone cradle.
i
This Operator's Manual describes op-
eration of the telephone using the
COMAND control unit and the multi-
function steering wheel. Unless other-
wise specified, the descriptions and
the illustrated displays refer to the
COMAND control unit.
Operation of the cellular phone and
voice control system* are explained in
separate operation guides.
!
Radio transmitters, such as a portable
telephone or a citizens band unit,
should only be used inside the vehicle if
they are connected to a separate exte-
rior antenna approved by Mercedes-
Benz.

88 Telephone*
Telephone operation
The unlock code protects the telephone
against unauthorized use. The unlock code
can be activated on the telephone
(
Telephone Operation Guide).
Commit your unlock code to memory.
The telephone functions are available only
after entering the unlock code.Example: unlock code 2307
In sequence, press the number
keysA, B," and @.
In case of erroneous entry, delete the
last or more digits:
Press the Delete soft key as often as
required.
After entering all digits, press' o r t h e
OK soft key.
All telephone functions are available if
the correct number has been entered.
After registering, Information referring
to the telephone signal appears at the
right end of the status bar.
The unlock code has to be entered
again if the entry was incorrect.When COMAND is switched ON, switching
to telephone mode from any other opera-
tion mode is made as follows.
On the COMAND control unit
Press2.
The Telephone main menu opens
(
page 89).
On the multifunction steering wheel
See (page 25)
Entering the unlock code
i
The system switches back to last mode
if the unlock code is not entered within
8 seconds after you are prompted to do
so.
Switching to telephone mode

91 Telephone*
Telephone operation
On the multifunction steering wheel
Presss .
In both cases the call is active. Commu-
nication is conducted via the hands-free
system. The call volume can be adjusted
(
page 29).
For other user functions, see
“Active call” (
page 95).
Ending or refusing a call
On the COMAND control unit
Press4.
On the multifunction steering wheel
Presst .The desired phone number has to be en-
tered when placing an outgoing call.
The following options are available:
entering a phone number directly
(
page 91)
initiating redial (page 92)
selecting an entry in the accepted and
missed calls list (
page 93)
selecting an entry in the dialed calls list
(
page 94)
using speed dial (page 95)
opening the phone book and selecting
an entry (
page 98)
Entering a phone number
Open the Telephone main menu
(
page 89).
Use" - = to enter the phone num-
ber.
In case of erroneous entry, you can de-
lete the last or more digits.
Press the Delete s o f t k e y a s o f t e n a s
required.
or
Press4 on the COMAND con-
trol unit ort on the multifunc-
tion steering wheel.
This deletes the entire entry.
After entering the phone number,
press3.
The telephone dials the entered num-
ber. The call is activated the moment
the other party answers the call. Com-
munication is conducted via the hands-
free system. The volume can be adjust-
ed (
page 29).
For other user functions, see
“Active call” (
page 95).
i
It is also possible to accept, refuse or
end a call from the cellular phone
(
Telephone Operation Guide).
Placing an outgoing call

92 Telephone*
Telephone operation
Initiating redial
On the COMAND control unit
Immediate re-dialing of the number dialed
last can be initiated:
Press3 in the Telephone main
menu twice.
The telephone establishes the connec-
tion with the number dialed last.
On the multifunction steering wheel
Switch the multifunction display in the
instrument cluster to the Telephone
main display (
page 25).
Presss twice.
The telephone establishes the connec-
tion with the number dialed last.In both cases the telephone initiates the
call. The call is activated the moment the
other party answers the call. Communica-
tion is conducted via the hands-free sys-
tem. The volume can be adjusted
(
page 29).
For other user functions, see
“Active call” (
page 95).
After switching to telephone operation,
COMAND can display the number of
missed calls in the status bar.COMAND automatically creates a list of
accepted and missed calls. This list can
contain 10 entries max.
The accepted and missed calls list can be
opened, an entry can be selected, and the
call can be returned.
i
When pressings only once, the di-
aled calls list appears in the multifunc-
tion display (
page 94).
Accepted and missed calls

94 Telephone*
Telephone operation
Selecting an entry from the list of di-
aled calls
COMAND automatically creates a list of di-
aled calls. This list can contain 10 entries
max. The list is sorted chronologically, the
last dialed call is displayed at the top of the
list.
On the COMAND control unit
Opening the list:
Press the Dialed # soft key in the Tele-
phone main menu (
page 89).
The list appears.Switching between number and names:
Press the 123 soft key.
This switches the list to number dis-
play.
If a name in the phonebook is stored
with the number of the highlighted call
it is shown in the status bar.
Press the ABC soft key.
This switches the list to name display.
The number in the phone book that be-
longs to the highlighted name is shown
in the status bar.Selecting a list entry and establishing the
connection:
Use% or & to select the desired
entry.
Press3.
The telephone initiates the call to the
selected number.
On the multifunction steering wheel
Opening the list:
Switch the multifunction display in the
instrument cluster to the Telephone
main display (
page 25).
Presss once.
The last dialed call is displayed on the
multifunction display.
Dialed calls
i
If no calls have been placed yet the
Dialed # soft is shaded out and without
function.
i
If you presss twice, the telephone
will immediately establish a connection
with the phone number dialed last.