clock reset MERCEDES-BENZ CLS55AMG 2006 W219 Owner's Manual

25 At a glance
Instrument cluster
Item
Page
1
LLeft turn signal
indicator lamp
2
vABS/ESP
® warning
lamp
353
3
Speedometer
4
Multifunction display
147
5
lDistance warning
lamp
Vehicles without Distronic*:
Warning lamp without func-
tion. It illuminates with the
ignition on. It should go out
when the engine is running.
357
6
KRight turn signal
indicator lamp
7
Coolant temperature indi-
cator with:•Coolant temperature
warning lamp
357
Item
Page
8
Tachometer with:1Supplemental
Restraint System
(SRS) indicator lamp
359
-Antilock Brake Sys-
tem (ABS) indicator
lamp
352
358
AHigh beam headlamp
indicator lamp
138
9
Main odometer with:

Selector lever position
49


Program mode
182
a
Clock with:
162
;Brake warning lamp,
USA only
354
3Brake warning lamp,
Canada only
354
Item
Page
úEngine malfunction
indicator lamp, USA
only
355
±Engine malfunction
indicator lamp, Cana-
da only
355
HCombination low tire
pressure/TPMS mal-
function telltale*,
Canada only
360
b
Fuel display with:AFuel reserve warning
lamp
358
c
Button for:

Resetting trip odometer
146


Adjusting instrument
cluster illumination
144


Confirming new time
settings
162

145 Controls in detail
Instrument cluster
To brighten illumination
Turn the reset button in the instrument
cluster clockwise (
page 24).
The instrument cluster illumination will
brighten.
To dim illumination

Turn the reset button in the instrument
cluster counterclockwise (
page 24).
The instrument cluster illumination will
dim.
Coolant temperature indicatorWarning!
G


Driving when your engine is overheated
can cause some fluids which may have
leaked into the engine compartment to
catch fire. You could be seriously
burned.


Steam from an overheated engine can
cause serious burns and can occur just
by opening the hood. Stay away from
the engine if you see or hear steam com-
ing from it.
Turn off the engine, get out of the vehicle
and do not stand near the vehicle until the
engine has cooled down.
!Excessive coolant temperature triggers
the coolant temperature warning lamp
(page 357) and a warning in the
multifunction display (
page 379).
The engine should not be operated with
the coolant temperature above 248°F
(120°C). Doing so may cause serious
engine damage which is not covered by
the Mercedes-Benz Limited Warranty.
iDuring severe operating conditions,
e.g. stop-and-go traffic, the coolant
temperature may rise close to 248°F
(120°C).

162 Controls in detailControl systemTime/Date submenu
Access the
Time/Date
submenu via the
Settings
menu. Use the
Time/Date
sub-
menu to change the time and date display
settings. The following functions are avail-
able:Synchronizing the time
This function can only be seen on vehicles
with COMAND and navigation module*.

Move the selection marker with the
æ or çbutton to the
Time/Date

submenu.

Press buttonj ork repeatedly
until you see
Time sync. with head
unit
in the multifunction display.
The selection marker is on the current
setting.

Press buttonæ orç to select
the desired setting.Set time (hours)
This function can only be seen when time
synchronization is switched off.

Move the selection marker with the
æ or çbutton to the
Time/Date

submenu.

Press buttonj ork repeatedly
until you see
Clock, hours
in the
multifunction display.
The selection marker is on the hour set-
ting.

Press buttonæ orç to set the
hour.

Confirm by pressing reset button
(page 24).
Function
Page
Synchronizing the time
162
Set time (hours)
162
Set time (minutes)
163
Set date (month)
163
Set date (day)
163
Set date (year)
164
iInformation on setting the time, refer to
separate COMAND instructions.

163 Controls in detail
Control system
Set time (minutes)
This function can only be seen when time
synchronization is switched off.
Move the selection marker with the
æ orçbutton to the
Time/Date

submenu.

Press buttonj ork repeatedly
until you see
Clock, minutes
in the
multifunction display.
The selection marker is on the minute
setting.

Press buttonæ orç to set the
minutes.

Confirm by pressing reset button
(page 24).Set date (month)

Move the selection marker with the
æ or çbutton to the
Time/Date

submenu.

Press buttonj ork repeatedly
until you see
Set date month
in the
multifunction display.
The selection marker is on the month
setting.

Press buttonæ orç to set the
month.Set date (day)

Move the selection marker with the
æ or çbutton to the
Time/Date

submenu.

Press buttonj ork repeatedly
until you see
Set date day
in the
multifunction display.
The selection marker is on the day
setting.

Press buttonæ orç to set the
day.