MERCEDES-BENZ E-Class 2005 W211 Comand Manual

90 Telephone*Telephone operation
ROAMING
= telephone is logged into a cel-
lular phone network outside your home
network,

NO SERV.
= no network available,

= telephone signal strength,

= call active (
page 96).
Other messages could also appear:

If the message Please insert phone
, Phone not installed
or
Please insert SIM card
appears, see chap-
ter “Switching the phone ON / OFF”
(
page 85)

If the message Please Enter PIN:
appears, see “Entering
the PIN” (
page 87)

If the message Enter unlock code:
appears, see “Enter-
ing unlock code” (page 88)Selectable soft keys and options

soft key
Opens the phone book (
page 98),

Recvd.#
soft key
Opens the accepted and missed calls
list (page 93),

Dialed #
soft key
Opens dialed calls list (
page 94),

SMS
soft key
Provides access to the SMS menu
(page 101),

Entry of a phone number (
page 91).The ringing tone is audible in the event of
an incoming call. The call screen pops up
on the current display.
If the multifunction display in the instru-
ment cluster is set to telephone mode, the
call screen also appears in the multifunc-
tion display.
iIf a list is empty, the corresponding soft
key is without function. This is indicat-
ed by the corresponding soft key dis-
play being shaded out.
Answering an incoming call

91 Telephone*
Telephone operation
Answering calls
On the COMAND control unit
Press.On the multifunction steering wheel

Presss
.
In both cases the call is active. Commu-
nication is conducted via the hands-free
system. The call volume can be adjusted
(
page 30).
For other user functions, see
“Active call” (
page 96).
Ending or refusing a call
On the COMAND control unit

Press.
On the multifunction steering wheel

Presst
.The desired phone number has to be en-
tered when placing an outgoing call.
The following options are available:

entering a phone number directly
(page 92)

initiating redial (
page 92)

selecting an entry in the accepted and
missed calls list (
page 93)

selecting an entry in the dialed calls list
(page 94)

using speed dial (
page 95)

opening the phone book and selecting
an entry (
page 99)
iThe caller’s number appears only if it is
transmitted.
The caller’s name only appears if, in ad-
dition, the number and the name are
stored in the phone book (
page 98).
iIt is also possible to accept, refuse or
end a call from the cellular phone
(Telephone Operation Guide).
Placing an outgoing call

92 Telephone*Telephone operationEntering a phone number 
Open the Telephone main menu
(page 89).

Use -  to enter the phone num-
ber.
In case of erroneous entry, you can de-
lete the last or more digits.
Press the
Delete
soft key as often as
required.

After entering the phone number,
press.
The telephone dials the entered num-
ber. The call is activated the moment
the other party answers the call. Com-
munication is conducted via the hands-
free system. The volume can be adjust-
ed (
page 30).
For other user functions, see
“Active call” (
page 96).Initiating redial
On the COMAND control unit
Immediate re-dialing of the number dialed
last can be initiated:

Press in the Telephone main
menu twice.
The telephone establishes the connec-
tion with the number dialed last.
On the multifunction steering wheel

Switch the multifunction display in the
instrument cluster to the Telephone
main display (
page 25).

Presss twice.
The telephone establishes the connec-
tion with the number dialed last.In both cases the telephone initiates the
call. The call is activated the moment the
other party answers the call. Communica-
tion is conducted via the hands-free sys-
tem. The volume can be adjusted
(
page 30).
For other user functions, see
“Active call” (
page 96).
After switching to telephone operation,
COMAND can display the number of
missed calls in the status bar.
iWhen pressings only once, the di-
aled calls list appears in the multifunc-
tion display (
page 94).
Accepted and missed calls

93 Telephone*
Telephone operation
COMAND automatically creates a list of
accepted and missed calls. This list can
contain 10 entries max.
The accepted and missed calls list can be
opened, an entry can be selected, and the
call can be returned.Selecting an entry from the list of ac-
cepted and missed calls.
Opening of list

Press the
Recvd.#
soft key in the Tele-
phone main menu (
page 89).
The list appears with the last call high-
lighted.
The list is sorted chronologically, the
last accepted or missed call is dis-
played at the top of the list.
iIf no calls have been received yet the Recvd.#
soft key is shaded out and with-
out function.
iThe list shows up to ten calls you re-
ceived last. It is a combined listing of
both accepted and missed calls. The
list does not show or specify which
calls were accepted and which ones
were missed.

94 Telephone*Telephone operationSwitching between number and names 
Press the
123
soft key.
This switches the list to number dis-
play.
or

Press the
ABC
soft key.
This switches the list to name display.
The number in the phone book that be-
longs to the highlighted name is shown
in the status bar.
Selecting a list entry and establishing
the connection

Use or  to select the desired
entry.

Press.
The telephone initiates the call to the
selected number.Selecting an entry from the list of di-
aled calls
COMAND automatically creates a list of di-
aled calls. This list can contain 10 entries
max. The list is sorted chronologically, the
last dialed call is displayed at the top of the
list.
On the COMAND control unit
Opening the list:

Press the
Dialed #
soft key in the Tele-
phone main menu (page 89).
The list appears.Switching between number and names:

Press the
123
soft key.
This switches the list to number dis-
play.
Dialed callsiIf no calls have been placed yet the Dialed #
soft is shaded out and without
function.

95 Telephone*
Telephone operation
If a name in the phonebook is stored
with the number of the highlighted call
it is shown in the status bar.

Press the
ABC
soft key.
This switches the list to name display.
The number in the phone book that be-
longs to the highlighted name is shown
in the status bar.
Selecting a list entry and establishing the
connection:

Use or  to select the desired
entry.

Press.
The telephone initiates the call to the
selected number.On the multifunction steering wheel
Opening the list:

Switch the multifunction display in the
instrument cluster to the Telephone
main display (
page 25).

Presss once.
The last dialed call is displayed on the
multifunction display.
Selecting a list entry and establishing the
connection:

Pressj or k repeatedly until
the desired entry is shown on the mul-
tifunction display.

Presss
.
The telephone initiates the call to the
selected number.
On the cellular phone, telephone numbers
can be stored in a speed dial memory
(
Telephone Operation Guide).
You can retrieve the entries of the speed
dial memory via COMAND.

Open the Telephone main menu
(page 89).

Press a number key between
and
 and hold it for more than approx.
2 seconds.
The telephone establishes the connec-
tion with the stored number.
iIf you presss twice, the telephone
will immediately establish a connection
with the phone number dialed last.
Speed dial

96 Telephone*Telephone operationThe call is activated the moment the other
party answers the call. The call display ap-
pears. The duration of the call is displayed
in the status bar.
On the multifunction steering wheel a call
screen is displayed if the multifunction dis-
play in the instrument cluster is switched
to Telephone main display (
page 26).The following functions are available dur-
ing a call:

Ending the active call (
page 96)

Switching the hands-free microphone
ON/OFF (
page 96)

Transmitting number sequences
(page 97)
Ending the active call
On the COMAND control unit

Press.On the multifunction steering wheel

Presst
.
Switching the hands-free microphone
ON/OFF
The soft key
Mic Off
shows the status of the
microphone.
Microphone OFF: soft key =
Microphone ON: soft key =

Press the
Mic Off
soft key.
This switches the microphone OFF or
ON. The display of the soft key changes
accordingly.
The other party cannot hear you if the
microphone is switched OFF; however,
you can hear the other party.
Active call

97 Telephone*
Telephone operation
Transmitting number sequences
Answering machines or other devices
could possibly be controlled through num-
ber sequences (e.g. remote query func-
tions). 
With an open connection, press one of
the appropriate number keys-
for each digit.
You can also transmit the
characters and # (#).

98 Telephone*Phone bookThe phone book contains all entries of the
cellular phone memory. On the COMAND control unit
Press the soft key in the Telephone
main menu (
page 89).
The Phone Book menu appears on the
display. The first list entry is highlighted
automatically.On the multifunction steering wheel

Switch the multifunction display in the
instrument cluster to the Telephone
main display (
page 26).

Pressj or k.
A phone book entry appears on the
multifunction display; scroll up or down
as required.
Phone Book menu An example for the Phone Book menu is
shown above. It shows a list of the phone
book entries whose names start with the
letter
B. Displayed in the status bar is the
number of the highlighted name, in this ex-
ample 18005551212
.
iIf a GSM phone is used, the phone book
contains all entries of the telephone
phone book.Opening the phone bookiIf no numbers are stored in the phone
book, the soft key is shaded out
and without function.
iVarious icons may be assigned to the
phone numbers, depending on the en-
try made on the telephone:
Home number
Work number
Fax number
Main number
Mobile number
Pager number
In the instrument cluster the name of
the category assigned to the phone
number, e.g.
Home
, appears in the multi-
function display.

99 Telephone*
Phone book
The following options are now available:
Switching between number and
name(
page 99).

Selecting a phone book entry and est-
sablishing a connection(
page 99).

Adding spoken names to a phone book
entry (
page 100). This option is only
available for vehicles with voice control
system*.

Deleting a phone book entry
(page 100).
Switching between number and name

Open the phone book from COMAND
(page 98).

Press the
123
soft key.
This switches the display to number
display. The name of the highlighted
entry is shown in the status bar;
or

Press the
ABC
soft key.
This switches the display to name dis-
play. The number of the highlighted en-
try is shown in the status bar.
On the COMAND control unit

Open the phone book (
page 98).
A list of phone book entries appears,
beginning with a specific first letter (ini-
tial).
Changing initials

Press or  once or repeatedly.
Each time you press the button, the
display changes to the next letter up or
down. At the end of the list of letters is the
category
Other
. This category combines
all entries without a name, or entries
whose names start with a special char-
acter (e.g.
* or
#).
Selecting an entry

If necessary, change the initial letter
(page 99).

Select an entry using  or .
If you press and hold either one of the
buttons, the scrolling up or down accel-
erates.
Establishing a connection

Press.
The telephone initiates the connection
with the appropriate number.
Selecting a phone book entry and es-
tablishing a connection