system MERCEDES-BENZ E-Class 2005 W211 Comand Manual

29 At a glance
Menu system
Exiting from submenus
You can exit the current submenu by
pressing the
Back
soft key. The display
switches to the next higher menu level.
The system does not accept setting modi-
fications which have not been stored.
There are exceptions where pressing the
Back
soft key will also store new settings.
These exceptions, whenever applicable,
are referenced on the following pages.

30 At a glanceQuick reference COMANDSwitching ON 
Turn the key in the steering lock to po-
sition 1 or 2,
or

Press .
COMAND switches on the last active
system and displays the corresponding
menu.
Switching OFF

Turn the key in the steering lock to po-
sition 0 and remove it,
or

Press .Different volume settings are possible for
Navigation*, Telephone*, or Voice con-
trol*.
A common volume setting is provided for
Radio, Single CD, MP3, CD changer*, AUX
and Satellite radio* operating modes.
When setting the volume, the system auto-
matically stores the setting for the current-
ly active operating mode. The volume of
navigation announcements can be
changed only during an actual announce-
ment.
iThe system can be operated as follows:
from COMAND itself, or

from the multifunction steering
wheel
This operating manual describes oper-
ation from COMAND and from the mul-
tifunction steering wheel.
Unless otherwise specified, the de-
scriptions and the displays illustrated
relate to the COMAND control unit.
Switching ON/OFF
iWithout the key in position 1 or 2 of the
steering lock, the system automatically
switches OFF again after approx. 30
minutes of inactivity.
iIf a telephone call is in progress (hands-
free) you cannot switch the COMAND
OFF, is disabled.Volume

31 At a glance
Quick reference COMAND
Setting the volume 
Turn the rotary control
located on
the COMAND control unit,
or

Pressæ or ç on the multifunc-
tion steering wheel
The volume changes up or down, de-
pending on the direction of rotation or
which button was pressed.The system stores the volume settings
when the device is switched OFF.
After switching the system back on again,
the volume may be lower than at the time
when the system was switched OFF.
This could be the case if:
the system was switched OFF for more
than 15 minutes, and

the volume had been set to a value in a
certain range at the time the device
was switched OFF.
Automatic volume control
The automatic volume control adjusts the
volume depending on

the vehicle’s speed (only in vehicles
without Sound-system*),
or on
the interior ambient noises of the vehi-
cle (only in vehicles with Sound-sys-
tem*)

other parameters (e.g. windows open
or closed)A common balance and fader setting ap-
plies to the following operating modes:

Radio

Single CD

MP3

CD changer*

AUX

Satellite radio*
When adjusting the balance or the fader,
the system automatically stores the set-
ting for the currently active operating
mode.Balance and faderiFor Navigation* a different balance/
fader setting is possible. You find the
description under “Adjusting the
acoustics for navigation announce-
ments” (
page 111).

33 At a glance
Quick reference COMAND
When adjusting bass or treble, the system
automatically stores the setting for the
currently active operating mode.
Setting bass and treble
Open the main menu of the appropriate
operating mode (
page 27).

Press the
Bass
or
Treble
soft key.
The Bass or Treble menu appears.

Press or .
The cursor moves horizontally, adjust-
ing bass or treble accordingly.Storing new settings

Press or the
Back
soft key,
or

wait until the display changes.
If the vehicle is equipped with a sound sys-
tem*, the sound functions are available for
the following operating modes:

Radio

Single CD

MP3

CD changer*

AUX

Satellite radio*The following sound functions are avail-
able:

Default Settings
:
Resets the sound functions to the fac-
tory setting.

Standard
:
Normal stereo playback.

Speech
:
Playback optimized for speech compre-
hension.

LOGIC7 Surround
:
7-channel-surround playback (not for
mono-sources like AM waveband or
Weather Band in radio mode).
Different sound functions can be activated
for each one of the operating modes listed
above.
Sound functions*

34 At a glanceQuick reference COMANDExample:
For CD mode: the
LOGIC7 Surround
function,
for Satellite radio* mode: the
Speech
func-
tion.
Switching sound functions

Open the main menu of the appropriate
operating mode (
page 27).

Press the
Sound
soft key.
The Sound menu appears.

Use or  to select the desired
function.

Press.
The system switches to the selected
function.iYour harman/kardon® audio system
features the innovative LOGIC7®
multi-channel surround sound technol-
ogy developed for the professional re-
cording industry.
By selecting the “LOGIC7 Surround”
function, LOGIC7® will be activated.
LOGIC7® converts any 2-channel ma-
terial into breathtaking multi-channel
surround sound and that without the
unnatural interpretation of many of to-
day’s surround sound techniques.
iLOGIC7® is not an artificial “effects”
button. It automatically adapts itself to
the incoming source material, adjust-
ing the seven outputs based on the
original acoustic intent of the studio
master.
harman/kardon LOGIC7® creates a
true 360-degree “enveloping” sound-
field with a maximum “audio sweet-
spot” for all passengers.
harman/kardon LOGIC7® sets a new
benchmark in musical clarity and sepa-
ration, giving the listener the impres-
sion of actually “being there”.
LOGIC7® playback works with all con-
ventional stereo audio sources (e.g.
stereo CD or stereo radio).
If the radio reception is poor, the sys-
tem should be switched back to Stan-
dard stereo playback. Switching back
to Standard stereo playback may im-
prove reception quality.

36 AudioAudio main menu
Press
.
The Audio main menu appears.
If one of the Audio submenus appears: 
Press the
Back
soft key as often as
necessary until the Audio main
menu appears,
or

Press
again.
Various audio sources can be selected in
the Audio main menu.

Radio
soft key
Station settings for WB, FM, and AM
wavebands appear (
page 37)

CD soft key or
MP3
soft key
The Single CD main menu (
page 46)
or the MP3 main menu (
page 53) ap-
pears

CDC
soft key
The CD changer main menu appears
(page 66)

AUX
soft key
Facilitates operation of an external au-
dio source (
page 72)Switching the mute function ON:

Press .
The system is switched to mute.
Switching the mute function OFF:

Press again,
or

Turn the rotary control
located on
the COMAND control unit,
or

Pressæ or ç on the multifunc-
tion steering wheel.
The audio source heard is the one se-
lected before the mute function was
activated.
Opening the Audio main menu
Selectable soft keysiThe Satellite Radio menu is accessed
by pressing (
page 75).
Mute functioniThe mute function is still activated if
the system is switched off and then on
again.

37 Audio
Radio operation

Radio operation

Open the Audio main menu
(page 36).

Press the
Radio
soft key.
The Radio main menu appears. The sta-
tion last tuned to will begin to play. In this example:

Weather Band


Channel 1
= current station

Press the
FM/AM
soft key in the Radio
main menu.
Alternatingly the Radio main menu for
the FM or AM wavebands appears. The
station last tuned to will begin to play.The waveband is indicated in the center
of the status bar.
In this example:

FM = FM waveband

1 = selected station is stored on
preset 1
Safety InstructionsWarning
G
In order to avoid distraction which could
lead to an accident, the driver should enter
system settings with the vehicle at a stand-
still and operate the audio system only when
road, weather and traffic conditions permit.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approximate-
ly 14 m) every second.Switching to radio mode
Switching wavebands

39 Audio
Radio operation

Pressk:
The next receivable descending fre-
quency is tuned in and begins to play.
Tuning via station presets
Ten presets each are available for FM and
AM. The presets are accessed using the
number keypad, or via the Presets menu.
Accessing via number keypad:

Switch to the desired waveband
(page 37).

Press one of the number keys

- :
The system tunes to the station stored
under this number.
Accessing via Presets menu:

Switch to the desired waveband
(page 37).

Press the
Presets
soft key.
The Presets menu appears.

Use , ,  or  to choose a
preset and press,
or

Press one of the number keys

- .
The system tunes to the station stored
under this number.
Tuning via Autostore presets
The Autostore function allows placing of
stations into the presets sorted by recep-
tion quality (
page 43). The system will store the station with the
strongest signal in preset 1.
Ten presets each are available for FM and
AM.

Switch to the desired waveband
(page 37).

Press the
Autost.
soft key.
The Autostore preset list appears. It
can take several seconds until all fre-
quencies are displayed.


40 AudioRadio operation
Use , ,  or  to choose a
preset and press.
or

Press one of the number keys

- .
The system tunes to the station stored
under this number.
Tuning via scan search
Scan search is characterized as follows:

Scan search performs two runs.
During the first run, stations with ex-
tremely good reception are played.
During the second run, stations with
weaker reception are played.

Scan search plays each receivable sta-
tion for approx. 8 seconds.

Scan search can be ended manually.

Scan search automatically stops at the
station listened to before the scan
search was started.
Starting scan search

Switch to the desired waveband
(page 37).

Press the
Scan
soft key.
Scanning begins.
Ending Scan search manually

Press the
Scan
soft key again.Manual tuning

Switch to the desired waveband
(page 37).

Press and hold or  for at
least 2 seconds to tune up or down.
Manual tuning is activated.

Keep the button pressed or release it
and keep tapping or  in
quick succession.
The frequency will change by the tuning
increments for the respective wave-
band each time one of the buttons is
pressed or for as long as a button is
pressed and held.
Manual tuning is deactivated if no but-
ton is pressed for approx. 3 seconds.

41 Audio
Radio operation
Tuning via direct frequency input
Entry example:
98.5 MHz in FM waveband
Switch to the FM waveband
(page 37).

Press.The frequency input display appears.
The frequency range of the FM wave-
band is shown.

Press the number buttons in
succession:, , and .
Each number entered appears in the
display.
The system tunes to the frequency en-
tered (in this example: 98.5 Mhz) and
switches back to the FM menu.Tuning via station search
Seven channels are available on the
Weather Band.
On COMAND control unit

Switch to the WB waveband by press-
ing the
WB soft key in the Radio main
menu (page 37).
iManual tuning is also possible in all
wavebands by pressing or .
The frequency will change by the tuning
increments for the respective wave-
band each time one of the buttons is
pressed.
Frequency increments for manual
tuning:
FM 0.2 MHz

AM 10 kHz
iEntries outside the frequency range are
not possible.
Within the AM waveband, the input is
restricted to frequencies within the re-
spective frequency increment, which
is10 kHz.
The system will select the nearest valid
frequency if a frequency outside the
frequency increment is entered.Tuning to a station on Weather Band