Page 22 MERCEDES-BENZ E-Class 2007 W211 Comand Manual

28 At a glance
Menu system
Right side:
General status information is displayed, re-
gardless of the selected operating mode.
In this example:
ROAMING = telephone* is logged into a
mobile communications network out-
side your home network.
 = telephone* signal strength
Menu functions and submenus
Using the soft keys, you can switch func-
tions ON or OFF, or open submenus.
Example: Radio main menu:
The Scan soft key switches the scan
search ON or OFF.
The Autost. soft key opens the submenu
for the Autostore settings.
In some situations, soft keys may not have
any function and thus not be available.
Should a soft key not be available, it will
appear shaded out, its characters will ap-
pear white.
Example:
Presets, Scan and Autost. soft key.Exiting from submenus
You can exit the current submenu by
pressing the
Back soft key. The display
switches to the next higher menu level.
The system does not accept setting modi-
fications which have not been stored.
There are exceptions where pressing the
Back soft key will also store new settings.
These exceptions, whenever applicable,
are referenced on the following pages.
i
This information is also displayed in
Navigation* mode (only in map dis-
plays).

30 At a glance
Quick reference COMAND
Setting the volume
Turn the rotary control* located on
the COMAND control unit,
or
Pressæ or ç on the multifunc-
tion steering wheel
The volume changes up or down, de-
pending on the direction of rotation or
which button was pressed.
The system stores the volume settings
when the device is switched OFF.
After switching the system back on again,
the volume may be lower than at the time
when the system was switched OFF.
This could be the case if:
the system was switched OFF for more
than 15 minutes, and
the volume had been set t o a value in a
certain range at the time the device
was switched OFF.
Automatic volume control
The automatic volume control adjusts the
volume depending on
the vehicle’s speed (only in vehicles
without Sound-system*),
or on
the interior ambient noises of the vehi-
cle (only in vehicles with Sound-sys-
tem*)
other parameters (e.g. windows open
or closed)A common balance and fader setting ap-
plies to the following operating modes:
Radio
Single CD
MP3
CD changer*
AUX
Satellite radio*
When adjusting the balance or the fader,
the system automatically stores the set-
ting for the currently active operating
mode.
Balance and fader
i
For Navigation* a different balance/
fader setting is possible. You find the
description under “Adjusting the
acoustics for navigation announce-
ments” (
page 109).

31 At a glance
Quick reference COMAND
Setting balance/fader
Open the main menu of the appropriate
operating mode (
page 27).
Press the Bal/Fad soft key.
The Balance/Fader menu is displayed.
Now you can set the balance and the
fader (
page 31).
A cross-hair cursor appears. The verti-
cal line indicates the balance setting.
The horizontal line indicates the fader
setting.
Press# or $:
The cursor moves horizontally, adjust-
ing the desired balance,
or
Press% or &:
The cursor moves vertically, adjusting
the fader.
Storing new settings:
Press' or the Back soft key,
or
wait until the display changes.For the following operating modes, differ-
ent settings for bass and treble can be se-
lected:
Radio (FM waveband)
Radio (AM waveband)
Radio (Weather Band)
Single CD
MP3
CD changer*
AUX
Satellite radio*
Navigation*
Bass and treble settings for navigation an-
nouncements are found under “Adjusting
the acoustics for navigation announce-
ments” (
page 109).
i
Using 7 and 8, the cursor can be
moved simultaneously in vertical and
horizontal direction (diagonally).
Bass and treble

32 At a glance
Quick reference COMAND
When adjusting bass or treble, the system
automatically stores the setting for the
currently active operating mode.
Setting bass and treble
Open the main menu of the appropriate
operating mode (
page 27).
Press the Bass or Treble soft key.
The Bass or Treble menu appears.
Press# or $.
The cursor moves horizontally, adjust-
ing bass or treble accordingly.Storing new settings
Press' or the Back soft key,
or
wait until the display changes.
If the vehicle is equipped with a sound sys-
tem*, the sound functions are available for
the following operating modes:
Radio
Single CD
MP3
CD changer*
AUX
Satellite radio*The following sound functions are avail-
able:
Default Settings:
Resets the sound functions to the fac-
tory setting.
Standard:
Normal stereo playback.
Speech:
Playback optimized for speech compre-
hension.
LOGIC7 Surround:
7-channel-surround playback (not for
mono-sources like AM waveband or
Weather Band in radio mode).
Different sound functions can be activated
for each one of the operating modes listed
above.
Sound functions*

33 At a glance
Quick reference COMAND
Example:
For CD mode: the
LOGIC7 Surround function,
for Satellite radio* mode: the
Speech func-
tion.
Switching sound functions
Open the main menu of the appropriate
operating mode (
page 27).
Press the Sound soft key.
The Sound menu appears.
Use% or & to select the desired
function.
Press'.
The system switches to the selected
function.
i
Your harman/kardon® audio system
features the innovative LOGIC7® multi-
channel surround sound technology
developed for the professional record-
ing industry.
By selecting the “LOGIC7 Surround”
function, LOGIC7
® will be activated.
LOGIC7
® converts any 2-channel ma-
terial into breathtaking multi-channel
surround sound and that without the
unnatural interpretation of many of to-
day’s surround sound techniques.
i
LOGIC7® is not an artificial “effects”
button. It automatically adapts itself to
the incoming source material, adjust-
ing the seven outputs based on the
original acoustic intent of the studio
master.
harman/kardon LOGIC7
® creates a
true 360-degree “enveloping” sound-
field with a maximum “audio sweet-
spot” for all passengers.
harman/kardon LOGIC7
® sets a new
benchmark in musical clarity and sepa-
ration, giving the listener the impres-
sion of actually “being there”.
LOGIC7
® playback works with all con-
ventional stereo audio sources (e.g.
stereo CD or stereo radio).
If the radio reception is poor, the sys-
tem should be switched back to Stan-
dard stereo playback. Switching back
to Standard stereo playback may im-
prove reception quality.

36 Audio
Audio main menu
Press-.
The Audio main menu appears.
If one of the Audio submenus appears:
Press the Back soft key as often as
necessary until the Audio main
menu appears,
or
Press- again.
Various audio sources can be selected in
the Audio main menu.
Radio soft key
Station settings for WB, FM, and AM
wavebands appear (
page 37)
CD soft key or MP3 soft key
The Single CD main menu (
page 46)
or the MP3 main menu (
page 55) ap-
pears
CDC soft key
The CD changer main menu appears
(
page 66)
AUX soft key
Facilitates operation of an external au-
dio source (
page 72)Switching the mute function ON:
Press (.
The system is switched to mute.
Switching the mute function OFF:
Press (0again,
or
Turn the rotary control* located on
the COMAND control unit,
or
Pressæ or ç on the multifunc-
tion steering wheel.
The audio source heard is the one se-
lected before the mute function was
activated.
Opening the Audio main menuSelectable soft keys
i
The Satellite Radio menu is accessed
by pressing; (
page 75).
Mute function
i
The mute function is still activated if
the system is switched off and then on
again.

37 Audio
Radio operation

Radio operation
Open the Audio main menu
(
page 36).
Press the Radio soft key.
The Ra dio m ain menu a ppears. The st a-
tion last tuned to will begin to play. In this example:
Weather Band
Channel 1 = current station
Press the FM/AM soft key in the Radio
main menu.
Alternatingly the Radio main menu for
the FM or AM wavebands appears. The
station last tuned to will begin to play.The waveband is indicated in the center
of the status bar.
In this example:
FM = FM waveband
1 = selected station is stored on
preset 1
Safety Instructions
WarningG
In order to avoid distraction which could
lead to an accident, the driver should enter
system settings with the vehicle at a stand-
still and operate the audio system only when
road, weather and traffic conditions permit.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approximate-
ly 14 m) every second.
Switching to radio modeSwitching wavebands

38 Audio
Radio operation
The following options are available:
Tuning via station search (page 38).
Tuning via station presets (page 39).
Tuning via Autostore presets
(
page 40).
Tuning via scan search (page 40).
Manual tuning (page 41).
Tuning via direct frequency input
(
page 41).
Tuning via station search
On COMAND control unit
Switch to the desired FM or AM wave-
band (
page 37).
Press+ or %:
The next receivable ascending frequen-
cy is tuned in and begins to play,
or
Press, or &:
The next receivable descending fre-
quency is tuned in and begins to play.
On multifunction steering wheel
Switch the multifunction display in the
instrument cluster to the Radio display
(
page 25).
Pressj:
The next receivable ascending frequen-
cy is tuned in and begins to play,
or
i
The wavebands cover different fre-
quency ranges.
FM broadcast band:
FM (VHF = very high frequency)
87.7 - 107.9 MHz
Tuning increments 0.2 MHz
AM broadcast band:
MW (medium wave)
530 - 1710 kHz
Tuning increments 10 kHz
WB waveband:
WB (Weather Band)
162.400 - 162.550 MHz
Tuning increments = 1 channel
Tuning to a FM/AM station
i
Audio search function Freq. must be
set in the multifunction display
(
page 26).

39 Audio
Radio operation
Pressk:
The next receivable descending fre-
quency is tuned in and begins to play.
Tuning via station presets
Ten presets each are available for FM and
AM.
On COMAND control unit
The presets are accessed using the num-
ber keypad, or via the Presets menu.
Accessing via number keypad:
Switch to the desired waveband
(
page 37).
Press one of the number keys
! - ":
The system tunes to the station stored
under this number.
Accessing via Presets menu:
Switch to the desired waveband
(
page 37).
Press the Presets soft key.
The Presets menu appears.
Use $, #, % or & to choose a
preset and press',
or
Press one of the number keys
! - ".
The system tunes to the station stored
under this number.On multifunction steering wheel
Switch the multifunction display in the
instrument cluster to the Radio display
(
page 25).
Pressj.
The system tunes to the next station
stored in the station presets;
or
Pressk.
The system tunes to the previous sta-
tion stored in the station presets.
i
Audio search function Memory must be
set in the multifunction display
(
page 26).

40 Audio
Radio operation
Tuning via Autostore presets
The Autostore function allows placing of
stations into the presets sorted by recep-
tion quality (
page 43).
The system will store the station with the
strongest signal in preset 1.
Ten presets each are available for FM and
AM.
Switch to the desired waveband
(
page 37).
Press the Autost. soft key.
The Autostore preset list appears. It
can take several seconds until all fre-
quencies are displayed.
Use $, #, % or & to choose a
preset and press'.
or
Press one of the number keys
! - ".
The system tunes to the station stored
under this number.Tuning via scan search
Scan search is characterized as follows:
Scan search performs two runs.
During the first run, stations with ex-
tremely good reception are played.
During the second run, stations with
weaker reception are played.
Scan search plays each receivable sta-
tion for approx. 8 seconds.
Scan search can be ended manually.
Scan search automatically stops at the
station listened to before the scan
search was started.
Starting scan search
Switch to the desired waveband
(
page 37).
Press the Scan soft key.
Scanning begins.