display MERCEDES-BENZ E-CLASS CABRIOLET 2022 User Guide

F
F
itting t
itting t he ISOFIX or i‑Size c
he ISOFIX or i‑Size c hild r
hild res
estrtraint syst
aint syst em
em
on t
on t he
heleT
leT and r
and r ight r
ight r ear seats
ear seats &
W
WARNING
ARNING Risk of accident if there ar
ben chseat, rear seat and seat backrest
are not engaged
The rear ben chseat, rear seat and seat bac k-
re st ma yfo ld forw ards, even while theve hicle
is in motion.
R As a result, theve hicle occupant will be
pressed into the seat belt with increased
fo rc e. The seat belt will not be able topro-
te ct as intended and could cause addi-
tional injur y.
R Objects or loads in the boot or load com-
partment cannot be restrained bythe seat
backrest. #
Make sure that there ar ben chseat, the
re ar seat and the seat backrest are
engaged before every trip. If
th e leT and right seat backrests are not
engaged and loc ked in place, this will be shown
on the display on the inst rument displa y. &
W
WARNI NG
ARNI NGRisk of injury or dea thifthe
permissible gross mass of thech ild and
ch ild restraint system toge ther is excee-
ded.
To o much load may be placed on the ISOFIX
or i‑Size child restraint systems and thech ild
may not be restrained co rrectly in theev ent of
an accident, forex ample. #
Ifth ech ild and thech ild restraint system
to get her weigh more than 33 kg, only
use an ISOFIX or i‑Size child restraint
system wi thwhich thech ild is secured
with theve hicle seat belt. #
Also secure thech ild restraint system
wi th th eTo pTe ther belt, if available. Alw
ays comply with the information about the
mass of thech ild restraint system:
R inthe manufacturer's installation and operat-
ing inst ructions forth ech ild restraint system
used
R on a label on thech ild restraint system, if
present Re
gula rly ch eck that the permissible gross mass
of thech ild and child restraint system is still com-
plied wi th.
When /tting a child restraint system, obse rvethe
fo llowing:
O Always obser vethe cor rect use of the seats
and consider their suitability for attaching a
ch ild restraint system.
ISOFIX child seat anchor (/ page 63)
or
i‑Size child seat anchor (/ page 64)
O Always comply with the manufacturer's
installation and operating instructions forthe
ch ild restraint system used.
O Makesure that thech ild's feet do not touch
th e front seat. If necessar y,mo vethe front
seat slightly forw ards.
® When /tting an ISOFIX child restraint sys-
te m, also obser vethefo llowing:
O When using a bab
When using a bab y car seat in w y car seat in weightgr
eight group
oup
0/0+ and a r
0/0+ and a r earw
earwar
ard-f
d-f acing c
acing c hild r
hild res
estrtraint
aint
syst
syst em in w
em in w eightgr
eight group 1 on a r
oup 1 on a r ear seat
ear seat:: Occupant saf
ety
65
65

#
Attach the ISOFIX or i‑Size child restraint sys-
te m to both mounting brac kets in theve hicle. #
ATer removing thech ild seat, reattach co vers
1 or2. F
F
ast
ast ening a T
ening a T opTet
op Tether
her &
W
W ARNING
ARNING Risk of injury or death if the
re ar seat backrests are not loc ked aTer
To pTe ther belts are /t ted
The rear seat backrests may fold forw ards
when you are driving.
As a result, child restraint systems will no lon-
ge r be able toper form their intended pr otec-
tive function. This may also cause additional
injuries. #
Always lock rear seat backrests aTer /t-
ting TopTe ther belts. #
Obser vethe lock veri/cation indicator. If
th e leT and right seat backrests are not
engaged and loc ked in place, this will be shown
on the display on the inst rument displa y. ¯
Ifth ech ild restraint system is equipped
wi th aTo pTe ther belt:
The risk of injury may be reduced byTo p
Te ther. The TopTe ther belt enables an
additional connection between thech ild
re straint system at tach ed with ISOFIX or
i‑Size and theve hicle. #
Place the ISOFIX or i‑Size child restraint sys-
te m with TopTe ther on there ar seat. It is
essential tocomply with thech ild restraint
system manufactu rer's installation inst ruc-
tions. #
Foldthere ar seat backrest forw ard
(/ page 120). #
Attach TopTe ther hook 2toTopTe ther
anchorage 1. #
Foldthere ar seat backrest back
(/ page 120). Occupant saf
ety
67
67

Fr
ont passenger airbag disabled 1, 2
U, L
W
W eight cat
eight cat egor
egory II: 15 t
y II: 15 t o 25 k
o 25 kgg
Fr ont passenger airbag enabled 1
UF, L
Fr ont passenger airbag disabled 1, 2
U, L
W
W eight cat
eight cat egor
egory III: 22 t
y III: 22 t o 36 kg
o 36 kg
Fr ont passenger airbag enabled 1
UF, L
Fr ont passenger airbag disabled 1, 2
U, L 1
Ad just the seat cushion inclination so that the front edge of the
seat cushion is in the highest position and there ar edge of the seat
cushion is in the lo west position.
2 The vehicle is equipped with automatic front passenger airbag
shuto.. The PASSENGER AIR BAG OFF indica tor lamp must be lit.
X Not suitable forch ildren in this we ight categor y.
U Sui table forch ild restraint systems of the "Universal" category in
th is we ight categor y.
L Suitable for semi-universal child restraint systems acco rding to
th eta ble in "Recommended child restraint systems", or if theve hi-
cle and the seat are listed in thech ild restraint system manufactur-
er's vehicle model list.
UF Suitable forfo rw ard-facing child restraint systems of the "Univer-
sal" category in this we ight categor y. Secur
Secur
ing t
ing t he c
he child r
hild r es
estrtraint syst
aint syst em wit
em with t
h t he seat
he seat
belt on t
belt on t he r
he rear seat
ear seat &
W
WARNING
ARNING Risk of accident if there ar
ben chseat, rear seat and seat backrest
are not engaged
The rear ben chseat, rear seat and seat bac k-
re st ma yfo ld forw ards, even while theve hicle
is in motion.
R As a result, theve hicle occupant will be
pressed into the seat belt with increased
fo rc e. The seat belt will not be able topro-
te ct as intended and could cause addi-
tional injur y.
R Objects or loads in the boot or load com-
partment cannot be restrained bythe seat
backrest. #
Make sure that there ar ben chseat, the
re ar seat and the seat backrest are
engaged before every trip. If
th e leT and right seat backrests are not
engaged and loc ked in place, this will be shown
on the display on the Instrument Displa y. Occupant saf
ety
69
69

*
N
NO
OTE
TE Damage tothe soT top due to
heavy objects Heavy, poin
ted or sharp-edged objects placed
on the soT top may damage it. #
Do not place any heavy objects on the
soT top. #
Do not sit on the soT top. Fo
r saf etyre asons, Mercedes-Benz recommends
opening or closing the soT top when theve hicle is
stationar y.
To open or close the soT top while you are driving,
do not exceed a maximum speed of 50 km/h. To
avo id inter rupting the closing process while you
are slightly exceeding this speed, do not drive at a
speed greater than 60 km/h. #
Make sure that the boot separator is closed. #
Close the boot lid. #
Switch on theve hicle. #
Keep the brake pedal depressed when the
ve hicle is stationar y. #
T To open: o open: pull and hold soT-top switch 1until
th e soT top is fully open.
The instrument display will show the opening
process of the soT top. #
T To close:
o close: press and hold soT-top switch 1
until the soT top is fully closed.
The instrument display will show the closing
process of the soT top. &
W WARNING
ARNING Risk of accident due toexces-
sive speed during the soT top opening or
closing procedure
If th eve hicle speed exceeds 60 km/h, the
soT top will stop during the opening or closing
procedure. #
Reduce theve hicle speed tobelow
60 km/h or stop theve hicle in accord-
ance with the tra1c conditions. #
Operate the soT- topswitch again to
open or close the soT top full y. The cur
rent procedure will be stopped at a speed
gr eater than 60 km/h. The message is shown on
th e inst rument displa y. #
Reduce your speed and press or pull soT top
switch 1again.
If th e soT top does not close fully because of
strong headwinds, drive more slo wlyor stop. 88
88
Opening and closing

R
R
eloc
eloc king t
king t he
hesoT
soT t
top
op &
W
WARNING
ARNING Risk of becoming trapped due
to the soT top lo wering unexpectedly
If yo u do not fully open/close the soT top, the
soT-top hydraulics will depressurise aTer a
short time. #
Always fully open or close the soT top. If
th e soT top has not been comple tely loc ked, the
inst rument display will show the message Open/
close soft top completely . In addition,you will
hear a warning tone for up to te n seconds while
driving. #
Stop theve hicle immediately in accordance
with the tra1c conditions. #
Make sure that theve hicle is switched on. #
Fully close the soT top using the soT- top
switch. Opening or closing t
Opening or closing t
he boo
he boot separ
t separ at
ator
or R R
eq
eq uir uir ements:
ements:
R Toopen the soT top: the manual boot separa-
to r must be closed.
% Invehicles with an automatic boot separator,
th is will automatically close when the soT top
is opened.
The boot separator co vers luggage or loads in the
boot.
Depending on the equipment, theve hicle may be
equipped with a manual or automatic boot separa-
to r.
* NO
NO TE TEDama getothe soT top or loads due
to long objects The soT
top or the load may be damaged
when the soT top is open. #
Do not place objects that are too long in
or behind the side luggage nets when the
boot separator partition is open. #
Make sure that the load does not push
th e boot separator upwards. #
V Vehicles wit ehicles wit h a manual boo
h a manual boo t separ
t separat
ator:
or: to
open, push boot separator 2inthe opposite
direction tothe ar row and into its upper end
position using the handle. #
V
Vehicles wit
ehicles wit h a manual boo
h a manual boo t separ
t separat
ator:
or: to
close, pull boot separator 2inthe direction
of the ar row by the handle until it rests on the
sides of the boot. Opening and closing
89
89

#
T
To f
o f old f
old f orw
orwar
ard:
d: pull seat release handle 1
and fold the seat backrest forw ards as far as it
will go.
The seat will automatically mo vetothefo re-
most position. #
T To f
o f old bac
old bac k:
k:swing the seat backrest back
horizontall y.
If th e seat backrest is not engaged, this will be
shown on the multifunction display on the
inst rument clus ter. A wa rning tone will also
sound.
The seat will automatically mo vetothe stored
position. F F
olding t
olding t he fr
he front seat bac
ont seat bac kr
kres
est f t forw
orw ar
ards/bac k-
ds/bac k-
w
w ar
ar ds (v
ds (v ehicles wit
ehicles wit hout memor
hout memor y function)
y function) F F
olding f olding f orw
orwar
ards
ds #
If necessar y,release the head restraint and
push it down. #
Pull seat release handle 1and fold the seat
backrest forw ards until the seat backrest
engages. #
Push the seat as farfo rw ards as it will go.
F
F olding back
olding back #
Push the seat back horizontally bythe seat
backrest until it reaches the seat position that
wa s pr eviously set. #
Foldthe seat backrest back until it engages.
Do so as smoo thly as possible.
If th e seat backrest is not engaged, this will be
shown on the multifunction display on the
inst rument cluster. A warning tone will also
sound. #
ATer the seat backrest has been folded bac k,
ch eck the position of the head restraint and
set it tothe cor rect position.
If th e set seat position can no longer be reached,
e.g. because of lug gage inthere ar foot we ll or
because occupants ha veentered there ar of the
ve hicle: #
Pull seat release handle 1again and return
th e seat backrest toan upright position.
The seat will lock in the new fore -and-aT posi-
tion. Seats and st
owing
109
109

&
W
WARNI NG
ARNI NGRisk of entrapment when
adjusting the seat with the memory func-
tion
When the memory function adjusts the seat,
yo u and other vehicle occupants – particular ly
ch ildren – could become trapped. #
During the adjustment process of the
memory function, make sure that no one
has any body parts in the sweep of the
seat. #
If someone becomes trapped, press a
preset position button or seat adjust-
ment switch immediatel y.&
W WARNI NG
ARNI NGRisk of entrapment if the mem-
ory function is activated bychildren
Children could become trapped if they acti-
va te the memory function, particular lywhen
unat tended. #
Never lea vechildren unattended in the
ve hicle. #
When leaving theve hicle, alw aysta ke the
ke y with you and lock theve hicle. Yo
u can use the memory function when theve hi-
cle is switched o..
Seat adjustments for up tothre e people can be
stored and called up using the memory function.
Yo u can sa vesettings forth efo llowing systems:
R Seat, backrest and head restraint
R Steering wheel
R Outside mir rors
R Head-up display Oper Oper
ating t
ating t he memor
he memor y function
y function S
S
t
tor
or ing
ing #
Set the desired position for all systems. #
Brie0y press theV memory button and
th en press preset position button 4,T
or U within thre e seconds.
An acoustic signal sounds. The settings are
stored. 116 116
Seats and st
owing

automatically
return tothe most recent origi-
nal position. #
Foldthe cor responding seat backrest 1back
until it engages.
If th e seat backrest is not engaged and
loc ked, this will be shown on the multifunction
display on the inst rument cluster. Ov Ov
er
ervie
vie w of t
w of t he tie-do
he tie-do wney
wn eyes
es Obser
vethe no tes on loading theve hicle
(/ page 117). 1
Tie-down eyes
Ve hicles with a draught stop: there is an addi-
tional tie-down eye behind there ar ben chseat
backrests. Toaccess this, the seat backrests
must be folded down (/ page 120). Ov
Ov
er
er vie
vie w of bag hooks
w of bag hooks &
W
WARNING
ARNING Risk of injury when using bag
hooks with heavy objects
The bag hooks cannot restrain he avy objects
or items of lug gage.
Objects or items of luggage may be 0ung
around and hit vehicle occupants. #
Only hang light objects on the bag
hooks. #
Never hang hard, sharp-edged or fragile
objects on the bag hooks. Subject
the bag hooks toa maximum load of 1 kg
and do not attach any goods tothem. Seats and st
owing
121 121

Char
Char
ging a mobile phone wir
ging a mobile phone wir elessly
elesslyR R
eq eq uir
uir ements:
ements:
R The mobile phone is suitable for wireless
ch arging (Qi-compatible mobile phone).
A list of Qi-compatible mobile phones can be
fo und at: https://www.mercedes-benz-
mobile.com. #
Place the mobile phone as close tothe centre
of mat 1as possible with the display facing
upwards.
When thech arging symbol is shown in the
multimedia system, the mobile phone is being
ch arge d. Malfunctions during
thech arging process are
shown in the central displa y.
% The mat can be remo vedfo r cleaning, e.g.
using clean, luk ewarmwater.
R R adio eq
adio eq uipment appr ov
uipment appr oval number
al number s f
s f or Br
or Br azil
azil
This device operates on a secondary basis, that is
to say it has no pr otection against harmful inter-
fe re nce, not even from the same type of stations,
and must not cause inter fere nce with systems
ope rating on a prima rybasis.
This product is permitted in accordance with the
procedure de/ned in Directive 242/2000 bythe
Brazilian telecommunications agency ANATEL and
meets the applicable tech nical requ irements.
Fu rther information is available on the ANATEL
we bsite. www.anatel.go v.br #
Further information on the declaration of con-
fo rm ity forve hicle components which receive
and/or transmit radio waves. F
F
itting and r
itting and r emo
emoving t
ving t he
he0oor
0oor mats
mats &
W
WARNING
ARNING Risk of accident due toobjects
in the driver's foot we ll
Objects in the driver's foot we ll may impede
pedal tr avel or block a depressed pedal.
This jeopardises the operating and road saf ety
of theve hicle. #
Stow all objects in theve hicle securely
so that they cann otget into the driver's
fo ot we ll. #
Always /t the 0oor mats securely and as
prescribed in order toensure that there
is alw ays su1cient room forth e pedals. #
Do not use loose 0oor mats and do not
place 0oor mats on top of one ano ther. Seats and st
owing
125 125

The high beam will switch o. automatically in
the
fo llowing cases:
R Atspeeds below 25 km/h
R Ifot her road users are de tected
R If st reet lighting is su1cient
% The system's optical sensor is located behind
th e windscreen near theove rhead control
panel.
Switc
Switc hing A
hing A dap
daptiv
tive Highbeam Assis
e Highbeam Assist ton/o.
on/o.
Switc
Switc hing on
hing on #
Turn the light switch totheà position. #
Switch on the high beam using the combina-
tion switch.
If Ad aptive Highbeam Assist is activated,
th e_ indicator lamp will light up on the
cent ral display section of the inst rument dis-
pla y.
Switc Switc hing
hingo.
o. #
Switch o. the high beam using the combina-
tion switch. A
A
dap
dap tiv
tive Highbeam Assis
e Highbeam Assist Plus t Plus A
A
dap
dap tiv
tive Highbeam Assis
e Highbeam Assist Plus function t Plus function &
W
WARNING
ARNING Risk of accident despite Adap-
tive Highbeam Assist Plus
Ad aptive Highbeam Assist Plus does not react
to:
R road users without lights, e.g. pedestrians
R road users with poor lighting, e.g. cyclists
R road users whose lighting is obstructed,
e.g. bya bar rier
On very rare occasions, Adaptive Highbeam
Assist Plus may failto recognise other road
users with their own lighting, or may recognise
th em too late.
In these, or in similar situations, the automatic
high beam will not be deactivated or will be
activated despite the presence of other road
users. #
Always obser vethero ad and tra1c con-
ditions carefully and switch o. the high
beam in good time. Ad
aptive Highbeam Assist Plus cann ottake into
account road, weather or tra1c conditions.
De tection may be restric ted in thefo llowing
cases:
R In poor visibility, e.g. fog, heavy rain or snow
R Ifth ere is dirt on the sensors or the sensors
are obscured
Ad aptive Highbeam Assist Plus is only an aid. Yo u
are responsible for adjusting theve hicle's lighting
to the pr evailing light, visibility and tra1c condi-
tions. Light and sight
133 133