wheel MERCEDES-BENZ E-CLASS COUPE 2009 Manual Online
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2009, Model line: E-CLASS COUPE, Model: MERCEDES-BENZ E-CLASS COUPE 2009Pages: 313, PDF Size: 7.76 MB
Page 266 of 313
Replacing the wiper blades
G
Ris
kofa ccident
The windscreen will not longer be wiped prop-
erl yift he wiper blades are worn. Thi scould
prevent yo ufrom observing the traffic condi-
tions ,thereby causing an accident. Replace
the wiper blades twice ayear, ideall yinspring
and autumn. G
Ris
kofa ccident
The wiper arm scould star tmoving and cause
an injury if yo uleave the windscreen wipers
switched on.
Remove the key from the ignition lock before
replacing the wiper blades.
! To avoid damaging the windscreen wiper
blades, make sure that yo utouch only the
wiper arm of the windscreen wiper. To remove
X Remove the key from the ignition lock or
turn the key to position 0(KEYLESS-GO).
X Fol dthe wiper arm away from the wind-
screen unti litengages.
X Set the wiper blad eatright angle stothe
wiper arm. X
Remove the wiper blad efrom the retainer
on the wiper arm in the direction of the
arrow. Fitting
X Slide the new wiper blad einto the retainer
on the wiper arm in the opposite direction
to the arrow.
X Turn the wiper blad eparalle ltot he wiper
arm.
X Fol dthe wiper arm back onto the wind-
screen. Flat tyre
Flat tyre equipmen
tvariants
Your vehicl emay be equipped with:
R aT IREFIT kit (Y page 207)
R a" Minispare" emergency spare wheel*
(Y page 208)
R the MOExtended run-flat sys-
tem* (Y page 272) Preparing the vehicle
i Vehicl epreparation is not necessary on
vehicles with MOE tyres*.
X Stop the vehicl easfar away as possible
from traffic on solid ,non-slipper yand level
ground.
X Switch on the hazard warning lamps.
X Firmly depres sthe parking brake.
X Vehicles with manual transmission:
engage firs torreverse gear.
X Vehicles with automati ctransmis-
sion*: move the selector lever to P.
X All occupants mus tget ou tofthe vehicle.
Make sure that they are not endangered as
they get ou tofthe vehicle.
X Make sure that no one is nea rthe danger
are aw hilst awheel is being changed .Any-
one wh oisnot directl yassisting in the
wheel change should, for example, stand
behind the barrier.
X Switch off the engine. Flat tyre
263Practical advice
*optional
207_AKB; 2; 3, en-GB
mkalafa
,V ersion: 2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 263 Z
Page 267 of 313
X
Vehicles withou tKEYLESS GO*:remove
the key from the ignition lock.
X Vehicles with KEYLES SGO*: openthe
driver' sdoor.
The on-board electronics have status 0,
which is the same as the key having been
removed.
X Ge toutof the vehicle.
X Close the driver' sdoor.
X Place the warning triangl e(Ypage 206) at
as uitabl edistance. Observe lega lrequire-
ments. Usin
gthe TIREFI Tkit
Yo uc an us ethe TIREFIT kit to sea lsmall
punctures, particularly thos einthe tyre tread.
Yo uc an us eTIREFIT at outsid etemperatures
dow nto- 20†. G
Risk of accident
In the following case syoursafety is especially
endangered, as tyre sealant is insufficient if:
R there are cuts or puncture sinthe tyre
greater than 4mm.
R the wheel rim is damaged.
R youh aved riven at very low tyre pressures
or on aflatt yre.
Do not drive any further. Consul taqualified
specialist worksho pwhich ha sthe necessary
specialist knowledg eand tool stocarryo ut
the work required.
Mercedes-Benz recommend sthat yo uuse a
Mercedes-Benz Service Centre for this pur-
pose. In particular, work relevant to safety or
on safety-related systems mus tbec arrie dout
at aq uali fied specialist workshop.
X Do not remove any foreign objects which
have penetrated the tyre ,e.g. screw sor
nails.
X Remove the TIREFIT kit, the accompanying
"max. 80 km/h "sticke rand the electri cair
pump from the stowag ewellu nderneath the luggage compartment floor
(Y
page 207). X
Affix part 0046of the sticke rwithin the driv-
er's field of vision.
X Affix part 0047of the sticke rnearthe valve
on the wheel with the defectiv etyre. G
Risk of injury
TIREFIT mus tnot come into contact with your
skin, eyes or clothing.
R If TIREFIT come sinto contact with your
eyes or skin, immediatel yrinse thoroughly
with clean water.
R Change ou tofclothing which ha scome into
contact with TIREFIT immediately.
R If an allergi creaction occurs, consult adoc-
tor immediately.
Kee pTIREFIT away from children.
R If TIREFIT is swallowed, immediatel yrinse
your mouth ou tthoroughly and drink plenty
of water.
R Do not induce vomiting. Consul tadoctor
immediately.
R Do not inhale TIREFIT fumes.
i If TIREFIT leaks out, allow it to dry .Itcan
then be removed like alayer of film.
If yo uget TIREFIT on your clothing, have it
cleane dassoona spossible with perchloro-
ethylene. 264
Flat tyrePractical advice
*o
ptional
207_AKB
;2;3,en-GB
mkalafa ,V ersion: 2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 264
Page 269 of 313
If
ap ressure of 1. 8bar is not reached
after fiv eminutes:
X Switch off and disconnect th eelectric air
pump and driv ethe vehicle forwards or
backwards approximately 10 m.
This distributes th eTIREFI Tmoree venly.
X Pump up th etyrea gain. G
Ris
kofa ccident
If ap ressur eof1.8bar is no tachieve dafter
fiv em inutes, th etyreist oobadly damaged.
Do no tdrivea ny further. Consult aqualified
specialist worksho pwhichh as th enecessary
specialist knowledge and tools to carry out
th ew ork required .Mercedes-Ben zrecom-
mends that you use aMercedes-Ben zService
Centr efor this purpose. In particular, work
relevan ttosafety or on safety-related sys-
tems must be carried out at aqualified spe-
cialist workshop.
When atyrep ressure of at leas t1.8bar
is reached:
X Press on/off switch 0088on th eelectric air
pump to 0.
The electric air pump is switched off.
X Remove th eTIREFI Tkit from th ewheel.
! Afte ruse, exces sTIREFI Tmay run out of
th ef ille rhose. This may caus estains.
Therefore, plac ethe fille rhoseint heplastic
whic hcontai nedt he TIREFI Tkit.
X Stow away th eTIREFI Tkit,t he electric air
pump and th ewarning triangle.
X Pul lawa yimm ediately.
X Stop after driving for approximately ten
minute sand check th etyrep ressur ewith
th ee lectric air pump. G
Ris
kofa ccident
If th etyrep ressur eisnowlower than 1. 3bar,
th et yreist oobadly damaged. Do no tdrive
any further. Consult aqualified specialist
worksho pwhichh as th enecessary specialist
knowledge and tools to carry out th ework required
.Mercedes-Ben zrecommends that
you use aMercedes-Ben zServic eCentr efor
this purpose. In particular, work relevan tto
safety or on safety-related systems must be
carried out at aqualified specialist workshop.
X If th etyrep ressur eisstill at least 1. 3bar,
correct it (see fuel fille rflap for values).
To increase th etyrep ressure: switch on
th ee lectric air pump.
To reduce th etyrep ressure: open pres-
sure release screw 0071on pressure
gauge 0072.
X Drive to th eneares tworksho pand have the
tyr ec hanged there.
X Hav ethe TIREFI Tkit replace dassoonas
possible at aqualified specialist workshop,
e.g. at aMercedes-Ben zServic eCentre. G
Ris
kofa ccident
Do no texcee dt he maximum spee dof
80 km/h.
The "max .80km/h" label must be affixe din
th ed river' sfieldofv ision.
The vehicle's handlin gcharacteristic smay be
affected. H
Environmental note
Hav ethe used TIREFI Tkit disposed of profes-
sionally, e.g. at aMercedes-Ben zService
Centre.
X Hav ethe TIREFI Tkit replace devery four
years at aqualified specialist workshop,
e.g. aMercedes-Ben zServic eCentre. 266
Flat tyrePractical advice
207_AKB
;2;3,en-GB
mkalafa ,V ersion: 2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 266
Page 271 of 313
When
atyre pressure of at leas t1.8 bar
is reached:
X Press on/off switch 008Aon the electric air
pump to 0.
The electric air pump is switched off.
X Remove the TIREFIT kit from the wheel.
! After use,e xcess TIREFIT may run out of
the filler hose. This may caus estains.
Therefore, place the filler hose in the plastic
which contained the TIREFIT kit.
X Stow away the TIREFIT kit, the electric air
pump and the warning triangle.
X Pull away immediately.
X Stop after driving for approximately ten
minutes and check the tyre pressure with
the electric air pump. G
Risk of accident
If the tyre pressure is now lower than 1.3 bar,
the tyre is too badly damaged. Do not drive
any further. Consult aqualified specialist
worksho pwhich has the necessary specialist
knowledge and tools to carry out the work
required .Mercedes-Benz recommends that
you use aMercedes-Benz Service Centre for
this purpose. In particular, work relevant to
safety or on safety-related systems must be
carrie dout at aqualified specialist workshop. X
If the tyre pressure is still at least 1.3 bar,
correct it (see fuel filler flap for values).
To increase the tyre pressure: switch on
the electric air pump. To reduce the tyre pressure:
press pres-
sure release button 0070next to pressure
gauge 0071.
X Drive to the neares tworksho pand have the
tyre changed there.
X Have the TIREFIT kit replaced as soon as
possible at aqualified specialist workshop,
e.g. at aMercedes-Benz Service Centre. G
Risk of accident
Do not exceed the maximu mspee dof
80 km/h.
The "max. 80 km/h" label must be affixe din
the driver's fiel dofvision.
The vehicle's handling characteristics may be
affected. H
Environmental note
Have the use dTIREFIT kit disposed of profes-
sionally ,e.g. at aMercedes-Benz Service
Centre.
X Have the TIREFIT kit replaced every four
years at aqualified specialist workshop,
e.g. aMercedes-Benz Service Centre. Changing
awheel and fitting the
spare wheel* G
Risk of accident
The whee ldimensions and tyre size of the
"Minispare" emergency spare wheel* may dif-
fer from those of the damaged wheel.
You rvehicle's handling characteristics will
change when a"Minispare" emergency spare
wheel* is fitted. Adapt you rstyle of driving
accordingly.
The "Minispare" emergency spare wheel*
may only be use dfor as hort time. Do not
exceed the maximu mspee dof80k m/h and
do not deactivate ESP ®
.
Never drive the vehicl ewith more than one
"Minispare" emergency spare wheel* fitted. 268
Flat tyrePractical advice
*o
ptional
207_AKB; 2; 3, en-GB
mkalafa,
Version: 2.11.8.1 2009-07-23T10:23:49+02:00-Seite 268
Page 272 of 313
G
Risk of accident
Have the collapsible emergency spare
wheel *replaced with anew wheel as soon as
possible at aqualified specialist workshop
which has the necessary specialist knowledge
and tools to carry out the work required.
Mercedes-Benz recommends that you use a
Mercedes-Benz Service Centr efor this pur-
pose. In particular, work relevant to safety or
on safety-related systems must be carried out
at aq ualified specialist workshop.
Preparing the vehicle i
Vehicles without aspare wheel* are not
equipped with wheel-changing tools at the
factory. For more information on which
tools are required to perform awheel
change on your vehicle, e.g. wheel chock,
centring pin or wheel wrench, consult a
Mercedes-Benz Service Centre.
X Prepare the vehicle as described
(Y page 263).
X Ifat railer is coupled to the vehicle, uncou-
ple it.
X Brin gthe wheels into the straight-ahead
position.
X Remove the following items from the stow-
age well under the boot floor:
R
the "Minispare" emergency spare
wheel*
R the vehicle tool kit
R the folding wheel chock
R the jack
Use the folding wheel choc ktopreventthe
vehicle from rolling away. X
Fold both plates 0046upwards.
X Fold out lower plate 0047.
X Guide the lugs on the lower plate fully into
opening sinbase plate 008A. Securin
gthe vehicle on level ground
X On level ground: place the folding wheel
choc kora similar item under the wheel that
is diagonally opposite to the wheel you wish
to change. Securin
gthe vehicle on slight downhill gradients Flat tyre
269Practical advice
*optional
207_AKB
;2;3,en-GB
mkalafa, Version:2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 269 Z
Page 273 of 313
X
On downhill gradients: place the folding
wheel choc korasimilar item behind the
wheels of the fron tand rear axle. X
Using wheel wrench 0088,loosen the bolts on
the wheel you wish to change by about one
full turn .Donot unscrew the wheel bolts
completely.
Raising the vehicle G
Risk of injury
The jack is designed only to raise the vehicle
for ashort time while awheel is being
changed.
The vehicle must be placed on stands if you
inten dtow ork under it.
Make sure that the jack is placed on afirm,
non-slip, level surface. Do not use wooden
blocks or similar objects as ajack underlay.
The vehicle could otherwise slip off the jack
and seriously injure you.
Do not start the engine at any time while the
wheel is being changed.
Do not lie under the vehicle when it is being
supported by the jack .Ifyou do not raise the
vehicle as described, it could slip off the jack
(e.g. if the engine is started or adoor or the
boot lid is opened or closed) and seriously
injure you. G
Risk of accident
If you fail to position the jack correctly, the
vehicle may: R
slip off the jack
R injure you or others
R be damaged.
Thus, it is important to make sure that the jack
is positioned correctly in the respective jack-
ing points .Befor epositioning the jack,
remove any dirt that may have collected in the
jacking points.
The jacking point sfor the jack are located
behind the wheel housings of the fron twheels
and in fron tofthe wheel housings of the rear
wheels (arrows). Vehicles with AMG equipment:
the vehicle
has cover sfitted to protec tthe vehicle body
nexttot he jacking point sonthe outer sills. Vehicles with AMG equipment*
0046
Cover
X Vehicles with AMG equipment*: fold
cover 0046upwards. 270
Flat tyrePractical advice
*o
ptional
207_AKB; 2; 3, en-GB
mkalafa,
Version:2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 270
Page 274 of 313
X
Position jack 008Aat jacking point 0047. X
Make sure that the base of the jack is posi-
tioned directly under jacking point 0047.
X Turn crank 0088until the tyre is raised amax-
imum of 3cmfrom the ground. X
Unscrew the uppermost wheel bolt com-
pletely.
X In place of the wheel bolt, screw centring
pin 0086from the vehicle tool kit into the
thread.
X Unscrew the remaining wheel bolts fully. !
Do not place wheel bolts in sand or dirt.
The threads of the wheel bolts and wheel
hubs could otherwise be damaged when
the bolts are tightened.
X Remove the wheel.
Fitting anew wheel G
Risk of accident
Replace damaged or corroded wheel bolts.
Never oil or grease wheel bolts. This could
cause the bolts to loosen in the wheel hub. G
Risk of accident
If aw heel hub thread is damaged, you must
not drive the vehicle any further .Consult a
qualified specialist workshop which has the
necessary specialist knowledge and tools to
carry out the work required. Mercedes-Benz
recommends that you use aMercedes-Benz
Servic eCentre or Servic e24h for this pur-
pose. In particular, work relevant to safety or
on safety-related systems must be carried out
at aq ualified specialist workshop. G
Risk of accident
Only use wheel bolts that have been designed
for the wheel and the vehicle. For safety rea-
sons, Mercedes-Benz recommends that you
only use wheel bolts which have been
approved for Mercedes-Benz vehicles and the
respective wheel. Other wheel bolts could
work loose or damage the brake system.
Do not tighten the wheel bolts completely
while the vehicle is still jacked up. The vehicle
could topple off the jack.
X Clean the wheel and wheel hub contact
surfaces. Flat tyre
271Practical advice
207_AKB; 2; 3, en-GB
mkalafa, Version: 2.11.8.1 2009-07-23T10:23:49+02:00-Seite 271 Z
Page 275 of 313
X
Place the emergenc yspare wheel ontot he
centring pin and push it on. X
Tighten the wheel bolts until they are fin-
ger-tight.
X Unscrew the centring pin.
X Tighten the last wheel bolt until it is finger-
tight.
Lowering the vehicle X
Lower the vehicle. To do this, turn the crank
of the jack anti-clockwise until the vehicle
is once again standin gfirmly on the ground.
X Place the jack to one side. X
Tighten the wheel bolts evenly in across-
wise patter ninthe sequence indica-
ted (0046 to0086). The tightening torque is
130 Nm. G
Risk of accident
Have the tightening torque checked immedi-
ately after awheel is changed. The wheels
could work loose if they are not tightened to
at orque of 130 Nm.
X Turn the jack back to its initial position and
store it together with the rest of the vehicle
tool kit in the stowage well under the boot
floor.
Vehicles with the "Minispare" emergency
spare wheel*:
X Transport the faulty wheel in the boot.
i When you are driving with the "Minispare"
emergenc yspare wheel* fitted, the tyre
pressure loss warning system* cannot
function reliably. MOExtended run-flat system*
The MOExtended run-flat system may only be
used in conjunction with the activated tyre
pressure loss warning system.
! The maximum permissible distanc ewhich
can be driven in run-flat mode depends on
the load in the vehicle. It is 80 km if the
vehicle is partially laden and 30 km if fully
laden. 272
Flat tyrePractical advice
*o
ptional
207_AKB; 2; 3, en-GB
mkalafa,
Version: 2.11.8.1 2009-07-23T10:23:49+02:00-Seite 272
Page 276 of 313
The maximum permissible distanc
ewhich
can be driven in run-flat mode is counted
from the moment the tyre pressure loss
warning appears in the multifunction dis-
play.
You must not exceed amaximum speed of
80 km/h. G
Risk of accident
The handling characteristics of your vehicle
deteriorate in run-flat mode, for example:
R when cornering
R when braking
R when acceleratin grapidly
Adapt your driving style accordingly and avoid
sudden changes in direction and sudden
acceleration ,aswell as driving over obstacles
(i.e. kerbs, potholes), and driving off-road.
This is particularly the case when the vehicle
is heavily laden.
The maximum permissible distanc ethat can
be driven in run-flat mode depends to alarge
exten tonthe loads placed on the vehicle. It
can be shorter due to high speeds, aheavy
load, sudden acceleration and/or manoeu-
vring, the road surface condition, outside tem-
perature, etc.,orf urther,ifyou drive carefully
and conservatively.
Do not continue to drive in run-flat mode if:
R you hear banging noises.
R the vehicle start stoshake.
R you see smoke and smell rubber.
R ESP ®
is intervening constantly.
R there are tears in the sidewalls of the tyre.
After driving in run-flat mode, you must have
the wheel(s) checked for damage at aquali-
fied specialist workshop which has the nec-
essary specialist knowledge and tools to carry
out the work required. The faulty tyre must be
replaced in every case.
Mercedes-Benz recommends that you use a
Mercedes-Benz Servic eCentre for this pur-
pose. In particular, work relevant to safety or on safety-related systems must be carried out
at
aq ualified specialist workshop.
Vehicles with MOExtended tyres*: when
replacing one or all tyres, make sure that you
only use tyres marked MOExtended and of
the specified size for the vehicle. Battery
Notes on the vehicle battery
In order for the battery to achieve the maxi-
mum possible service life, it must alway sbe
sufficiently charged.
Have the battery charge checked more fre-
quently if you use the vehicle mainly for short
trips or if you leave it standin gidle for a
lengthy period.
To prevent damage from corrosion, only
replace the battery with one that has acentral
ventilation cover.
Consult aMercedes-Benz Servic eCentre if
you wish to leave your vehicle parked up for
al ong period of time. G
Risk of injury
Comply with safety precautions and take pro-
tective measures when handling batteries. Risk of explosion
Fire, naked flames and
smokin
gare prohibited
when handling the battery.
Avoid creatin gsparks. Battery acid is caustic.
Avoid contact with the skin,
eyes or clothing.
Wear suitable protective
clothing, in particular
gloves, an apron and
aface
mask.
Immediately rinse acid
splashes off with clean Battery
273Practical advice
*optional
207_AKB; 2; 3, en-GB
mkalafa,
Version: 2.11.8.1 2009-07-23T10:23:49+02:00-Seite 273 Z
Page 282 of 313
Fitting th
etowing eye
Vehicles with atraile rtow hitch*: if you
inten dtou se thevehicl efor towing, fol dout
th eb all couplin gand connec tthe towbar
(Y page 193) to this.
Opening th ecovers The mounting
sfor th eremovable towin geyes
are locate dinthebumpers .They are located
at th efront and rear behind covers. Coupé (example)
X
Press cover 0046inwards on th emarkin gin
th ed irection of th earrow.
X Tak ecover 0046 off th eopening but do not
remove it.
Securing th etowing eye X
Tak ethe towin geye and th ewheel wrench
from th evehicl etoolkit (Y page 207).
X Screw in th etow inge ye clockwise to the
stop.
X Inser tthe wheel wrench handle int othe
towin geye and tighten it. Towing th
evehicle
! You may to wthe vehicl efor am aximum
of 50 km .Atowings pee dof50k m/hm ust
no tbee xceeded.
Fo rtow ingd istances ove r50km,thee ntire
vehicl emust be lifted up and transported.
! The engin emust be switched off (key in
ignition loc kinposition 0or position 1)if
th ev ehicl eisb eingtow ed wit hthe front
axle raised or if th eparking brak eisbeing
tested on adynamometer. Otherwise,
intervention by ESP ®
could damag ethe
brak esystem.
Vehicles with manua ltra nsmission X
Turn th ekeyto position 2(Y page 65 )in
th ei gnition lock.
X Fully depress th eclutch pedal.
X Shift to neutral.
Vehicles with automatic transmission* X
Turn th ekeyto position 2(Y page 65 )in
th ei gnition lock.
X Shift th etransmission to position N. Tow-starting (emergency engine
starting)
Pleas enote:
R Vehicles wit hanautomatic transmission*
must no tbetow-started.
R The battery must be connected.
R The engin eand catalyti cconverter must be
cold.
R Avoid repeated and lengthy starting
attempts.
Vehicles with manua ltra nsmission X
Turn th ekeyto position 2(Y page 65 )in
th ei gnition lock.
X Fully depress th eclutch pedal. Towin
gand tow-starting
279Practical advice
*optional
207_AKB
;2;3,en-GB
mkalafa, Version:2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 279 Z