lock MERCEDES-BENZ E-CLASS SALOON 2021 Repair Manual

4MA
4MA
TIC v
TIC v ehicles/v
ehicles/v ehicles wit
ehicles wit h aut
h automatic tr
omatic tr ans-
ans-
mission
mission #
Make sure that the front and rear axles come
to rest on the same transpor tation vehicle.
* N
NOOTE
TE Damage tothe drive train due to
incor rect positioning of theve hicle #
Do not position theve hicle abo vethe
connection point of the transport vehi-
cle. T
T
o
o wing ey
wing eye st
e st or
orag
ag e location
e location The
towing eye is located in the st owage space
under the boot 0oor. F
F
itting and r
itting and r emo
emoving t
ving t heto
he towing eye
wing eye #
Press the mark on co ver1 inwa rds and
re mo ve. #
Screw intheto wing eye clockwise as far as it
will go and tighten.
V
V ehicles wit
ehicles wit h a tr
h a trailer hitc
ailer hitc h:
h:vehicles with a trailer
hitch do not ha veare ar brac ketfo rth eto wing
ey e. Fasten theto w bar tothe trailer hitch. #
Make sure that co ver1 engages in the
bumper when youre mo vetheto wing eye.
* N
NOOTE
TE Damage totheve hicle due toincor-
re ct use of theto wing eye or trailer hitch When a
towing eye or trailer hitch is used to
re co ver a vehicle, theve hicle may be damaged
in the process. #
Only use theto wing eye or trailer hitch to
to w awa y or tow start theve hicle. #
Do not use theto wing eye or trailer hitch
to to wtheve hicle during reco very. Breakd
own assistance
391
391

R
Fuse box on the driver's side of the cockpit
(/ page 394)
R Fuse box in the front passenger foot we ll
(/ page 394)
R Fuse box in the boot on theright-hand side of
th eve hicle, when vie wed in the direction of
tr ave l (/ page 394) Opening and closing t
Opening and closing t
he fuse bo
he fuse box in t
x in the engine
he engine
com
com par
partment
tment R
R
eq
eq uir
uir ements:
ements:
R A dry clo thand a scr ewdriver are available.
Obser vethe no tes on elect rical fuses
(/ page 392).
Opening
Opening &
W
WARNING
ARNING Risk of injury from using the
windscreen wipers when the bonnet is
open
If th e windscreen wipers start moving when
th e bonnet is open, you could be trapped by
th e wiper linkage. #
Always switch o. the windscreen wipers
and theve hicle /r stifyo u need toopen
th e bonnet. #
Turn clips 2on co ver1 aqu arter-turn to
anti-clockwise. #
Pull co ver1 upwards in the direction of the
ar ro w. #
Remo veany existing moisture from the fuse
box using a dry clo th. #
Loosen scr ews4 and remo vefuse box lid 3
from theto p.
Closing
Closing #
Check whe ther the seal is positioned cor rectly
in cap 3. Breakdown assistance
393
393

#
Insert lid 3into the brac ket at there ar of the
fuse box. #
Fold down lid 3ofthe fuse box and tighten
scr ews4. #
Insert co ver1 on bo thsides. #
Turn clips 2on co ver1 aqu arter-turn
clockwise. #
Close the bonnet. Opening and closing t
Opening and closing t
he fuse bo
he fuse box in t
x in the coc
he coc kpit
kpit R
Obser vethe no tes on elect rical fuses
(/ page 392).
The fuse box is on the driver's side on the side of
th e cockpit under a co ver. #
Toopen and close it, consult a Mercedes-Benz
Service Centre. Opening and closing t
Opening and closing t
he fuse bo
he fuse box in t
x in the fr
he front
ont
passeng
passeng er f
er foo
ootw
twell
ell Obser
vethe no tes on elect rical fuses
(/ page 392). #
T
T o open:
o open: open cover1 inthe direction of the
ar ro w and remo veit. #
T To close:
o close: reinsert co ver1. Opening and closing t Opening and closing t
he fuse bo
he fuse box in t
x in the boot
he boot Obser
vethe no tes on elect rical fuses
(/ page 392). #
Fold co ver1 down in the direction of the
ar ro w.
The fuse assignment dia gram is in a recess on the
side of the fuse box. 394
394
Breakdown assistance

1
Jack
2 Wheel wrench
3 Centring pin
4 Folding chock
5 Ratchet for jack
Plug-in h
Plug-in h ybr
ybr id
id
The tyre-change tool kit is located in tool bag 1
on the boot 0oor. Pr
Pr
epar
epar ing t
ing the v
he vehicle f
ehicle f or a wheel c
or a wheel c hange
hange R
R
eq
eq uir
uir ements:
ements:
R The vehicle is not on a slope.
R The vehicle is on solid, non-slippery and le vel
gr ound.
R The requ ired tyre-change tool kit is available.
% Ifyo ur vehicle is not equipped with the tyre-
ch ange tool kit, consult a quali/ed specialist
wo rkshop to/nd out about sui table tools. #
Apply the electric parking brake manuall y. #
Movethe front wheels tothe straight-ahead
position. #
ShiT the transmission toposition 005D. #
V
Vehicles wit
ehicles wit h lev
h level contr
el contr ol syst
ol system:
em:setthe nor-
mal vehicle le vel (/ page 251). #
Switch o. theve hicle. #
Make sure that theve hicle cann otbe star ted. #
Place choc ks orother suitable items under the
front and rear of the wheel that is diagonal ly
opposite the wheel you wish tochange. #
If necessar y,remo vethe wheel trim/hub caps
(/ page 405). #
Raise theve hicle (/ page 406). R
R
emo
emo ving and
ving and /tting
/ttingt
the wheel tr
he wheel tr im/hub caps
im/hub caps R
R
eq
eq uir
uir ements:
ements:
R The vehicle is prepared for a wheel change
(/ page 405).
Plas
Plas tic hub cap
tic hub cap #
T
To r
o r emov
emov e:
e:turn the centre co ver of the hub
cap anti-clockwise and remo vethe hub cap. #
T
To
o /t:
/t: make sure that the centre co ver of the
hub cap is turned anti-clockwise. Wheels and tyres
405
405

#
Position the hub cap and turn the centre co ver
clockwise until the hub cap engages ph ysically
and audibl y.
Aluminium hub cap
Aluminium hub cap #
T
To r
o r emov
emov e:
e:position soc ket2 from the tyre-
ch ange tool kit on hub cap 1.#
Position wheel spanner 3on soc ket2. #
Using wheel spanner 3, turn hub cap1
anti-clockwise and remo veit. #
T
To
o /t:
/t: follow the inst ructions abo veinreve rse
order.
% Speci/ed
Speci/ed tight
tightening t
ening t orq
orque:ue: 25 Nm. R
R
aising t
aising t he v
he vehicle when c
ehicle when c hanging a wheel
hanging a wheel R R
eq
eq uir uir ements:
ements:
R There are no persons in theve hicle.
R The vehicle has been prepared for a wheel
ch ange (/ page 405).
R The wheel trims and hub caps ha vebeen
re mo ved (/ page 405).
Impor tant no tes on using the jack:
R Use only a vehicle-speci/c jack that has been
appr ovedby Mercedes-Benz toraise theve hi-
cle.
R The jack is only designed forra ising and hold-
ing theve hicle for a short time while a wheel
is being changed and not for maintenance
wo rkunder theve hicle.
R The jack must be placed on a /rm, 0at and
non-slip sur face. If necessar y,use a lar ge, 0at,
load-bearing, non-slip underla y.
R The foot ofthe jack must be positioned verti-
cally under the jack support point. Ru
les of conduct when theve hicle is raised:
R Never place your hands or feet under theve hi-
cle.
R Never lie under theve hicle. 406
406
Wheels and tyres

#
Position support 2of jack 4on jack sup-
port point 1. #
Turn ratchet 3clockwise until support 2
sits comple tely on jack support point 1and
th e base of the jack lies evenly on thegr ound. #
Turn ratchet 3until the tyre is raised a maxi-
mum of 3 cm from thegr ound. #
Loosen and remo vethe wheel (/ page 408). R
R
emo
emo ving a wheel
ving a wheel R R
eq eq uir
uir ements:
ements:
R The vehicle is raised (/ page 406).
* NO
NOTE
TEMercedes-AMG vehicles #
Obser vethe no tes in the Supplement.
Yo u could otherwise failto recognise
dangers. When
changing a wheel, avoid applying any force
to the brake discs, as this could impair the le vel of
comfort when braking.
* N
NOOTE
TE Damage tothre ading from dirt on
wheel bolts #
Do not place wheel bolts in sand or on a
dirty sur face. #
Unscr ewthe uppermost wheel bolt com-
ple tely. #
Screw cent ring pin 1into theth re ad ins tead
of the wheel bolt. #
Unscr ewthere maining wheel bolts com-
ple tely. #
Remo vethe wheel. F F
itting a ne
itting a ne w wheel
w wheel *
N NOOTE TE Mercedes-AMG vehicles #
Obser vethe no tes in the Supplement.
Yo u could otherwise failto recognise
dangers. 408 408
Wheels and tyres

&
W
W ARNI NG
ARNI NGRisk of accident from losing a
wheel
Oiled or greased wheel bolts can cause the
wheel bolts tocome loose, as too can dam-
aged wheel bolts or wheel hub thre ads. #
Never oil or grease theth re ads. #
Intheev ent of damage totheth re ads,
contact a quali/ed specialist workshop
immediatel y. #
Have the damaged wheel bolts or dam-
aged hub thre ads replaced. #
Do not continue driving. #
Obser vethe information on thech oice of tyres
(/ page 400).
Fo r tyres with a speci/ed direction of rotation, an
ar ro w on the side wall of the tyre indicates the
cor rect direction of rotation. Obser vethe direc-
tion of rotation when /tting. #
Slide the wheel tobe mounted onto the cen-
tring pin and push it on. &
W
WARNING
ARNING Risk of injury from tightening
wheel bolts and nuts
If yo u tighten the wheel bolts or wheel nuts
when theve hicle is raised, the jack could tip. #
Only tighten wheel bolts or wheel nuts
when theve hicle is on thegr ound. #
Be sure toobser vethe inst ructions and saf ety
no tes on "Changing a wheel" (/ page 400). #
For saf etyre asons, only use wheel bolts which
ha ve been appr oved byMercedes-Benz and
fo rth e wheel in question. #
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated until they are
/nger-tight. #
Unscr ewand remo vethe centring pin. #
Tighten the last wheel bolt until it is /n ger-
tight. #
Lowe rth eve hicle (/ page 409). Low Low
er
ering t
ing t he v
he vehicle
ehicle aTer
aTera wheel c
a wheel c hange
hange R
R
eq
eq uir
uir ements:
ements:
R The new wheel has been /tted (/ page 408). #
T
To low
o low er t
er the v
he v ehicle:
ehicle: placethera tchet onto
th e he xagon nut of the jack so that the letters
"AB" are visible and turn anti-clockwise. #
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated 1to5 with
an initial maximum forc e of 80 Nm. #
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated 1to5 with
th e speci/ed tightening torque of 150 Nm. Wheels and tyres
409
409

Displa
Displa
y messag
y messag es P
es Possible causes/conseq
ossible causes/consequences and uences and0050
0050Solutions
Solutions
Á
Key not detected (white dis-
play message) *T
hekey is cur rently unde tected. #
Change the location of theke y in theve hicle. #
Ifth eke y is still not recognised, place it in the slot for starting with theke y (/ page 168).
Á Key not detected (red dis-
play message) *T
hekey cann otbe de tected and may no longer be in theve hicle.
The key is no lon ger in theve hicle and you switch o. theve hicle:
R You can no longer start theve hicle.
R You cannot centrally lock theve hicle. #
Ensu rethat theke y is in theve hicle.
If th eke y de tection function has a malfunction due toa st rong radio signal source: #
Stop theve hicle immediately in accordance with the tra1c conditions. #
Place theke y in the slot for starting the engine with theke y (/ page 168).
Á Key being initialised Please
wait *T
hevehicle is processing in order to teach in the new key. #
Wait until processing is comple te. Display messages and
warning/indicator lamps
439
439

Displa
Displa
y messag
y messag es P
es Possible causes/conseq
ossible causes/consequences and uences and0050
0050Solutions
Solutions
ò
Acoustic presence indica-
tor inoperative *T
he sound generator (acoustic vehicle warning system) is malfunctioning. No driving noises are being produced. The
ve hicle may not be heard by otherroad users. #
Drive with particular care. #
Consult a quali/ed specialist workshop.
00E5
Charger cable connected *Y
ou cannot pull away while thech arging cable is connected. #
Disconnect thech arging cable from theve hicle.
Not possible to unlock
charging cable See Own-
er's Manual *T
hecharging cable connector cann otbe remo ved from thech arging station's soc ket. #
Press the EMERGENCY OFF switch on thech arging station.
If th ech arging cable connector cann otbe remo ved aTer that: #
Request service personnel from the operator of thech arging station via the emer gency call button attached tothe
ch arging station or the emer gency call numbers.
Vehicle not currently being
charged Charging station
fault *A
malfunction has occur red in thech arging station or the RFID card is not recognised. #
Start thech arging process at a di.erent charging station.
or #
Have the RFID card checkedto ensure it is functioning. Display messages and
warning/indicator lamps
447
447

Displa
Displa
y messag
y messag es P
es Possible causes/conseq
ossible causes/consequences and uences and0050
0050Solutions
Solutions
ï
Operation only possible in
transmission position P *T
he ball neck will not swivel because transmission position 005B,005Eor neutral 005Cis selected. #
Depress the brake pedal. #
Engage park position 005D.
ï Trailer coupling extending… *T
he ball neck is retracting/extending.
Do not attem pttospeed up, slow down or initiate the swivel mo vement using your hand, foot or other aids. During the
swivel mo vement, do not couple a trailer.
When the ball neck has reached an operational position, the display message will disappear.
ï Check trailer hitch
lock (white display message) *T
he trailer hitch is not operational during a jou rney with a trailer. &
W WARNING
ARNING Risk of an accident if the ball neck is not loc ked
The trailer may become de tach ed. #
Stop theve hicle immediately in accordance with the tra1c conditions. Do not continue driving. #
Uncouple the trailer and secure it against rolling away. #
Initiate a new swivel mo vement and do not re-couple the trailer until thewa rning/indicator lamp goes out. #
Initiate a new swivel mo vement (/ page 273). #
When the display message disappears, couple up the trailer and drive on. Display messages and
warning/indicator lamps
453
453