lock MERCEDES-BENZ E WAGON 2005 S211 Manual Online

247 Controls in detail
Loading
Loading
Split rear bench seat
To expand the cargo compartment, you
can fold down the left and right rear seat
backrests.
The two sections can be folded down sep-
arately to enlarge the cargo compartment.Folding the backrest forward
1Release catch
2Seat cushion

Pull release catch1 and use it to pull
seat cushion2 up.1Release catch
2Seat backrest

Pull release catch1 up.
The seat backrest is released and the
head restraints fold back.

Fold the seat backrest2 forward.
Warning!
G
When expanding the cargo compartment, al-
ways fold the seat cushions fully forward.
Unless you are transporting cargo, the back-
rests must remain properly locked in the up-
right position.
In an accident, during hard braking or sud-
den maneuvers, loose items will be thrown
around inside the vehicle, and cause injury
to vehicle occupants unless the items are
securely fastened in the vehicle.
Always use the cargo tie down rings
(page 251).
!You must always release the seat cush-
ion and fold it up before folding the seat
backrests forward. The upholstery on
the backrest may otherwise be dam-
aged.
iIf tall persons have occupied the
driver’s and front passenger seats, it
may be necessary to move these seats
forward slightly in order to fold the rear
seat backrests forward.

248 Controls in detailLoadingReturning seat backrest to original po-
sition
1Seat cushion
2Seat backrest
Swing seat backrest2 to the rear until
it engages.

Swing seat cushion1 to the rear and
press down from the rear of the cush-
ion until it audibly engages.

Swing the head restraint forward by
hand until it engages.
iIf the rear center seat is to be occupied
while driving, it may be necessary to
fold the seat belt buckle up again.
Warning!
G
Always lock backrest in its upright position
when rear seat bench is occupied, or the ex-
tended cargo compartment is not in use.
Check for secure locking by pushing and
pulling on the backrest.
In an accident, during hard braking or sud-
den maneuvers, loose items will be thrown
around inside the vehicle, and cause injury
to vehicle occupants unless the items are
securely fastened in the vehicle.
To help avoid personal injury during a colli-
sion or sudden maneuver, exercise care
when transporting cargo.

253 Controls in detail
Loading

Turn mounting element 2 toL.

Insert mounting element 2 in cargo
rail 1.

Turn mounting element 2 until it en-
gages in the‹ position.
You should be able to feel the mounting
element engage in the cargo rail.Inserting the cargo tie-down ring in the
mounting element
1Cargo tie-down ring
2Mounting element

Turn mounting element 2 in the cargo
rail toN.

Insert cargo tie-down ring 1 into
mounting element 2.

Turn mounting element 2 until it en-
gages in the‹ position.
Y o u s h o u l d b e a b l e t o f e e l t h e m o u n t i n g
element engage in the cargo rail.
iYou can turn the mounting element in
the cargo rail to four positions:
‹To lock the mounting element.
NTo insert or remove the cargo
tie-down ring, the belt reel or
the telescoping rod.
LTo insert or remove the mount-
ing element.
STo move the mounting element
to the next engaging point.
Warning!
G
The cargo tie-down rings should be subject
to equal loads. Make sure to comply with
the information provided in the loading in-
structions (
page 250).

254 Controls in detailLoadingBelt reel
1Belt reel
2Mounting element
3Locking button

Insert two mounting elements 2 into a
cargo rail.

Turn mounting element 2 in the cargo
rail toN.

Insert belt reel 1 into mounting ele-
ment 2.

Turn mounting element 2 in the cargo
rail until it engages in the‹ posi-
tion.
You should be able to feel the mounting
element engage in the cargo rail.

Press locking button 3 on the belt reel
and pull cargo net out in direction of ar-
row.

Place load between the cargo net and
the side wall of the cargo compart-
ment.

Press locking button 3 on belt reel.
With the other hand, slowly pull net
over load until it is taut.Telescoping rod
1Telescoping rod
2Mounting element
iThe belt reel can be used to tighten
light-weight loads against the side wall
of the cargo compartment, thus secur-
ing them from slipping.
iThe telescoping rod can be used to
tighten the load against the rear seats
so as to secure it from slipping.

255 Controls in detail
Loading

Insert one mounting element 2 into
each cargo rail.

Turn mounting element 2 in cargo rail
toN.

Insert telescoping rod 1 into mount-
ing element 2.

Turn mounting element 2 in cargo rail
until it engages in the‹ position.
You should be able to feel the mounting
element engage in the cargo rail.Storage box in cargo compartment
(Canada only)
1Storage boxWarning!
G
When you are using the storage box in the
cargo compartment, the backrests of the
seats in front of it must be completely en-
gaged to the rear, and the twin roller blind
must be installed.
Do not exceed the storage box’s maximum
load of 44 lbs (20 kg), as it could otherwise
become detached during an accident or
sharp braking maneuvers, and could injure
you or other passengers.
When leaving the vehicle, always remove the
SmartKey or the SmartKey with
KEYLESS-GO* from the starter switch, take
it with you, and lock the vehicle. Do not
leave children unattended in the vehicle, or
with access to an unlocked vehicle. Unsu-
pervised use of vehicle equipment may
cause an accident and/or serious personal
injury.

256 Controls in detailLoadingInstalling the storage box
Fold rear seat backrests forward
(page 247).

Insert storage box from behind into
cargo compartment with the opening
pointing in the direction of travel.

Press locking hooks of storage box into
the space between the rear seat back-
rest and the cargo compartment.

Fold rear seat backrest to the rear
(page 248).
Loading the storage box

Fold rear seat backrests forward
(page 247).

Fill storage box with cargo through the
opening on the front side.

Fold rear seat backrest to the rear
(page 248).
Removing the storage box

Fold rear seat backrests forward
(page 247).

Slide locking hooks of storage box for-
ward out of the retainers.

Pull storage box to the rear and remove
it from cargo compartment.

Fold rear seat backrest to the rear
(page 248).
Twin roller blind
The twin roller blind contains a cargo net
and a luggage cargo compartment.
It is located on the seat backrest of the
rear bench seat.
Cargo net
iThe storage box is additionally held in
place from above by the twin roller
blind.
iThe storage box in the cargo compart-
ment is covered by the rear bench seat
and can hold a maximum of 44 lbs
(20 kg) cargo.
Warning!
G
The cargo net cannot hold back heavy loads.
The transported load should therefore al-
ways be tied down.
Objects which are insufficiently secured
could otherwise injure you if they are thrown
around in the event of an accident, during
hard braking or steering maneuvers.

257 Controls in detail
Loading
1Cargo net
2Mountings for cargo net
Pull cargo net 1 up and hook it onto
mountings 2.Cargo compartment cover
The cargo compartment cover unlocks
automatically while the tailgate is open-
ing/closing and is automatically raised/
lowered.
It is therefore unnecessary to roll up the
cargo compartment cover before loading
and unloading. 1Cargo compartment cover
Rolling up the cargo compartment cover

Unhook cargo compartment cover
from its anchorages on the left and
right sides.

Slowly guide cargo compartment cover
back until it stops.
iYou can use the cargo net even when
the rear seat backrest is folded for-
ward. The cargo net should then be
hooked onto the front mountings.
!When loading the vehicle, make sure
not to load the cargo compartment
over the lower edge of the side win-
dows.
The twin roller blind could otherwise be
damaged when the tailgate is being
closed.

264 Controls in detailUseful featuresRemoving cup holder
1Cup holder
2Locking pins
Move both locking pins2 in direction
of arrow.

Take cup holder out upward.Reinstalling cup holder
3Locking pins

Insert cup holder.

Move both locking pins3 in direction
of arrow.Rear cup holder

Briefly press the front of the armrest.
The cup holder extends automatically.

266 Controls in detailUseful featuresCigarette lighter
The cigarette lighter is located in the
center console compartment in front of the
center armrest (
page 28).
1Cigarette lighter

Switch on the ignition.

Push in cigarette lighter1.
The lighter will pop out automatically
when hot.
12-V socket*
The socket is located in the rear of the cen-
ter console storage compartment.
The socket can be used for accessories up
to a maximum of 180 W.
Warning!
G
Never touch the heating element or sides of
the lighter; they are extremely hot. Hold the
knob only.
When leaving the vehicle, always remove the
SmartKey or the SmartKey with
KEYLESS-GO* from the starter switch, take
it with you, and lock the vehicle. Do not
leave children unattended in the vehicle, or
with access to an unlocked vehicle. Unsu-
pervised use of vehicle equipment may
cause an accident and / or serious personal
injury.iThe lighter socket can be used to ac-
commodate electrical accessories up
to a maximum 85 W.
iAn additional socket is located on the
left side in the cargo compartment.

270 Controls in detailUseful featuresThe Tele Aid system
(Tele
matic A
larm I
dentification on D
e-
mand)
The Tele Aid system consists of three
types of response:


automatic and manual emergency


Roadside Assistance and


information
The Tele Aid system is operational provid-
ing that the vehicle’s battery is charged,
properly connected, not damaged and cel-
lular and GPS coverage is available.
The speaker volume of a Tele Aid call can
be adjusted when using the volume control
on the multifunction steering wheel. To
raise, press buttonæ and to lower,
press buttonçor use the volume knob
on your COMAND headunit.

To activate, press the SOS button, the
Roadside Assistance button• or
the Information button¡, depend-
ing on the type of response required.
Shortly after the completion of your ac-
quaintance call, you will receive a user ID
and password via first call mail. By visiting
www.mbusa.com and selecting “Tele Aid”
(USA only), you will have access to account
information, remote door unlock and
more.System self-check
Initially, after switching on ignition, mal-
functions are detected and indicated (the
indicator lamps in the SOS button, the
Roadside Assistance button• and the
Information button¡ stay on longer
than ten seconds or do not come on). The
message
TELE AID malfunction – Drive
to workshop
appears for approximately
ten seconds in the multifunction display.
iThe SOS button is located above the in-
terior rear view mirror.
The Roadside Assistance button•
and the Information button¡ are
located below the center armrest cov-
er.
iThe Tele Aid system utilizes the cellular
network for communication and the
GPS (Global Positioning System) satel-
lites for vehicle location. If either of
these signals are unavailable, the
Tele Aid system may not function and if
this occurs, assistance must be sum-
moned by other means.