octane MERCEDES-BENZ E WAGON 2005 S211 Owner's Manual

13 Introduction
Operator’s Manual
Operating your vehicle outside the USA or Canada
If you plan to operate your vehicle in for-
eign countries, please be aware that:

service facilities or replacement parts
may not be readily available,


unleaded gasoline for vehicles with cat-
alytic converters may not be available;
the use of leaded fuels will damage the
catalysts,


gasoline may have a considerably low-
er octane rating, and improper fuel can
cause engine damage.Certain Mercedes-Benz models are avail-
able for delivery in Europe under our Euro-
pean Delivery Program. For details, consult
your authorized Mercedes-Benz Center or
write to:
In the USA:
Mercedes-Benz USA, LLC
European Delivery Department
One Mercedes Drive
Montvale, NJ 07645-0350
In Canada:
Mercedes-Benz Canada, Inc.
European Delivery Department
98 Vanderhoof Avenue
Toronto, Ontario M4G 4C9

297 Operation
At the gas station

Replace the fuel cap by turning it to the
right.
You will hear when the fuel cap is tight-
ened.

Close the fuel filler flap.
Check regularly and before a long trip
1Windshield washer and headlamp
cleaning system*
2Brake fluid
3Coolant level
iLeaving the engine running and the fuel
cap open can cause the yellow fuel
tank reserve warning lamp to flash and
the? malfunction indicator lamp
(USA only) or the ± malfunction in-
dicator lamp (Canada only) to illumi-
nate.
For more information, see “Practical
hints” (
page 357).
iOnly use premium unleaded gasoline
with a minimum Posted Octane Rating
of 91 (average of 96 RON / 86 MON).
Information on gasoline quality can
normally be found on the fuel pump.
More information on gasoline can be
found in the Factory Approved Service
Products pamphlet.
iOpening the hood, see (
page 299).

442 Technical dataEngineModel
E 320 (211.265
1)
E 320 4MATIC (211.282
1)
1The quoted data apply only to the standard vehicle. See an authorized Mercedes-Benz Center for the corresponding data of all special bodies and special equipment.
E 500
2 (211.270
1)
E 500 4MATIC (211.283
1)
2Not available in the U.S.Engine
112
113
Mode of operation
4-stroke engine, gasoline injection
4-stroke engine, gasoline injection
No. of cylinders
6
8
Bore
3.54 in (89.90 mm)
3.82 in (97.00 mm)
Stroke
3.31 in (84.00 mm)
3.31 in (84.00 mm)
Total piston displacement
195.2 cu.in. (3199 cm
3)
303.0 cu.in. (4966 cm
3)
Compression ratio
10:1
10:1
Output acc. to SAE J 1349
221 hp / 5600 rpm
3
(165 kW / 5600 rpm)
3Premium fuel required. Performance may vary with fuel octane rating.
302 hp / 5600 rpm
3
(225 kW / 5600 rpm)
Maximum torque acc. to SAE J 1349
232 lb-ft / 3000 rpm - 4800 rpm
(315 Nm / 3000 rpm - 4800 rpm)
339 lb-ft / 2700 rpm - 4250 rpm
(460 Nm / 2700 rpm - 4250 rpm)
Maximum engine speed
6000 rpm
6000 rpm
Firing order
1-4-3-6-2-5
1-5-4-2-6-3-7-8
Poly-V-belt
2390 mm
2390 mm

451 Technical data
Fuels, coolants, lubricants etc.
Model
Capacity
Fuels, coolants, lubricants etc.
Power steering
approx. 1.1 US qt (1 l)
MB Power Steering Fluid (Pentosin CHF 11S)
Front wheel hubs
approx. 3.0 oz (85 g) each
High temperature roller bearing grease
Brake system
1.1 US qt (1.05 l)
MB Brake Fluid (DOT 4+)
Cooling system
E 320 / E 320 4MATIC
10.7 US qt (10 l)
MB 325.0 Anticorrosion / Antifreeze
E 500
1/ E 500 4MATIC
1Not available in the U.S.
11.9 US qt (11.3 l)
Fuel tank
including a reserve of
21.12 US gal (80.0 l)
2.38 US gal (9.0 l)
Premium unleaded gasoline:
Minimum Posted Octane 91 (Avg. of 96
RON / 86 MON)

454 Technical dataFuels, coolants, lubricants etc.Premium unleaded gasoline
Gasoline additives
A major concern among engine manufac-
turers is carbon build-up caused by gaso-
line. Mercedes-Benz recommends only the
use of quality gasoline containing additives
that prevent the build-up of carbon depos-
its.
After an extended period of using fuels
without such additives, carbon deposits
can build up especially on the intake valves
and in the combustion area, leading to en-
gine performance problems such as:

Warm-up hesitation


Unstable idle


Knocking/pinging


Misfire


Power lossIn areas where carbon deposits may be en-
countered due to lack of availability of
gasolines which contain these additives,
Mercedes-Benz recommends the use of
additives approved by us for use on
Mercedes-Benz vehicles. Refer to Factory
Approved Service Products Pamphlet for a
listing of approved product(s). Follow di-
rections on product label.
Do not blend any specific fuel additives
with fuel. This only results in unnecessary
costs and may be harmful to the engine op-
eration.
Damage or malfunction resulting from
poor fuel quality or from blending addition-
al fuel additives other than those tested
and approved by us for use on
Mercedes-Benz vehicles listed in the Fac-
tory Approved Service Products pamphlet
are not covered by the Mercedes-Benz
Limited Warranty.
!To maintain the engine’s durability and
performance, premium unleaded gaso-
line must be used. If premium unleaded
gasoline is not available and low octane
fuel is used, follow these precautions:

Have the fuel tank only partially
filled with unleaded regular and fill
up with premium unleaded as soon
as possible


Avoid full throttle driving and abrupt
acceleration


Do not exceed an engine speed of
3000 rpm if the vehicle is loaded
with a light load such as two per-
sons and no luggage


Do not exceed
2/3 of maximum ac-
celerator pedal position if the vehi-
cle is fully loaded or operating in
mountainous terrain

455 Technical data
Fuels, coolants, lubricants etc.
Fuel requirements
Use only premium unleaded gasoline
meeting ASTM standard D 439:

The octane number (posted at the
pump) must be 91 “min”. It is an aver-
age of both the Research (R) Octane
Number and the Motor (M) Octane
Number: (R+M) / 2). This is also known
as the ANTI-KNOCK INDEX.
Unleaded gasoline containing oxygenates
such as ethanol, IPA, IBA and TBA can be
used provided the ratio of any one of these
oxygenates to gasoline does not exceed
10%; MTBE must not exceed 15%.The ratio of methanol to gasoline must not
exceed 3% plus additional cosolvents.
Using mixtures of ethanol and methanol is
not allowed. Gasohol, which contains 10%
ethanol and 90% unleaded gasoline, can be
used.
These blends must also meet all other fuel
requirements, such as resistance to spark
knock, boiling range, vapor pressure, etc.
Coolants
The engine coolant is a mixture of water
and anticorrosion / antifreeze, which pro-
vides:

Corrosion protection


Freeze protection


Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory
with a coolant providing freeze protection
to approximately -22°F (-30°C) and corro-
sion protection.
If the antifreeze mixture is effective to
-22°F (-30°C), the boiling point of the cool-
ant in the pressurized cooling system is
reached at approximately 266°F (130°C).
The coolant solution must be used
year-round to provide the necessary corro-
sion protection and increase boil-over pro-
tection. Refer to Maintenance Booklet for
replacement interval.

462 Technical termsMaintenance System (U.S. vehicles)
Maintenance service indicator in the
multifunction display that informs the
driver when the next vehicle mainte-
nance service is due. The Vehicle Main-
tenance System in your vehicle tracks
distance driven and the time elapsed
since your last maintenance service,
calculates other maintenance service
work required, and calls for the next
maintenance service accordingly.
Maximum load rating
(
page 333)
Maximum loaded vehicle weight
(page 333)
Maximum tire inflation pressure
(page 334)
Memory function*
Used to store three individual seat,
steering wheel and exterior mirror posi-
tions for each SmartKey.MON
(M
otor O
ctane N
umber)
The Motor Octane Number for gasoline
as determined by a standardized meth-
od. It is an indication of a gasoline's
ability to resist undesired detonation
(knocking). The average of both the
MON (Motor Octane Number) and
->RON (Research Octane Number) is
posted at the pump, also known as
ANTI-KNOCK INDEX.
Multifunction display
The display field in the instrument clus-
ter used to present information provid-
ed by the control system.
Multifunction steering wheel
Steering wheel with buttons for operat-
ing the control system.
Normal occupant weight
(
page 334)Overspeed range
Engine speeds within the red marking
on the tachometer dial. Avoid this en-
gine sp ee d ra nge , a s i t m ay re sul t in s e-
rious engine damage that is not
covered by the Mercedes-Benz Limited
Warranty.
Poly-V-belt drive
Drives engine-components (alternator,
AC compressor, etc.) from the engine.

463 Technical terms
Power train
Collective term designating all compo-
nents used to generate and transmit
motive power to the drive axles, includ-
ing:


Engine


Clutch/torque converter


Transmission


Transfer case*


Drive shaft


Axle shafts/axles
Production options weight
(
page 334)
PSI
(Pounds per s
quare i
nch)
(
page 334)Program mode selector switch
Used to switch the automatic transmis-
sion between standard operationS and
operationC.
E 55 AMG with steering wheel gearshift
control and manual shift program: in
addition to S and C (for sporty S or
comfortable C operation), you can use
M for manual shift program.
Restraint systems
Seat belts, belt tensioners, air bags and
child restraint systems. As indepen-
dent systems, their protective func-
tions complement one another.
Rim
(
page 334)RON
(R
esearch O
ctane N
umber)
The Research Octane Number for gaso-
line as determined by a standardized
method. It is an indication of a gaso-
line's ability to resist undesired detona-
tion (knocking). The average of both
the ->MON (Motor Octane Number)
and RON (Research Octane Number) is
posted at the pump, also known as
ANTI-KNOCK INDEX.
SBC
(S
ensotronic B
rake C
ontrol)
Electronically controlled hydraulic
braking system for increased braking
safety and comfort.
Shift lock
When the vehicle is parked, this lock
prevents the transmission selector le-
ver from being moved out of positionP
without the ignition or engine on and
brake pedal depressed.

476 IndexLow beam headlamps 51
Messages in display 387
Replacing bulbs 410, 411
Lowering
Vehicle 422
M
Main Dimensions 448
Maintenance 12
Maintenance service
Maintenance service data
information 343
Overdue 340
Resetting maintenance service
indicator 341
When due 339
Maintenance service indicator 339
Calling up 341
Clearing 340
Resetting 341
Maintenance System (U.S. vehicles) 462
Malfunction
Displaying 161
Manual headlamp mode 142
Manual operations
Fuel filler flap 405
Interior lighting control 148Sliding/pop-up roof* 407
Unlocking the driver’s door 404
Unlocking the gear selector
lever 405
Massage function 131
MAXCOOL maximum cooling 216
Maximum inflation pressure 334
Maximum load rating 333
Maximum loaded vehicle weight 333
Mechanical key 404
Memory function 138, 462
Recalling positions from
memory 139
Storing exterior rear view mirror park-
ing positions 140
Storing SmartKey dependent
settings 139
Menus 156
AUDIO 158
Distronic* 160, 235
In control system 156, 157
Settings menu 162
Standard display 158
Submenus 155
TEL* 179
Trip computer 178Vehicle status message memory 161
Miles/kilometers in speedometer
Setting 165
Minispare wheel
Mounting 421
Mirrors
Adjusting 41
Auto-dimming for rear view
mirrors 191
Auto-dimming mirror 191
Exterior rear view mirror 42
Exterior rear view mirror parking
positions 176, 192
Interior rear view mirror 42
Storing exterior mirror parking
position 140
MON 297
MON (Motor Octane Number) 462
Mph or km/h in speedometer 165
Multifunction display 153, 462
Selecting language 166
Standard display 157

480 IndexRecovery services
For stolen vehicle 277
Regular checks 297
Reinstalling the battery 427
Remote control
SmartKey with KEYLESS-GO* 107
Remote controls
Integrated 279
SmartKey 102, 107
Remote door unlock
With Tele Aid* 276
Removing
Vehicle battery 426
Wheel 421
Wiper blades 417
Removing and installing
Front seat head restraints 126
Removing and installing seat
cushions 136
Removing the storage box 256
Removing the twin roller blind 258
Replacing
Bulbs 410
Front lamp bulbs 413
Fuses 434
License plate lamp bulbs 415Rear lamp bulbs 411, 415
Side marker lamp bulb 415
Wiper blades 416
Reporting
Safety defects 18
Reprogramming
integrated remote control 282
Reset button in the instrument
cluster 162
Resetting
All functions (control system) 162
All functions of a submenu 163
Fuel consumption 178
Maintenance service indicator 341
Service indicator (FSS) 342
Trip odometer 151
Residual heat utilization 207, 219
Residual ventilation 219
REST (Residual engine heat
utilization) 219
Restraint system see Infant and child re-
straint systems 73
Rim 334
Rims and Tires 443
Roadside Assistance
Tele Aid* 269Roadside assistance 12
Rolling code programming 280
Rolling up the cargo compartment
cover 257
RON 297
RON (Research Octane Number) 463
Rubber parts
Cleaning 350
S
Safety
Occupant 62
Safety belts see Seat belts 44
Safety defects
Reporting 18
Safety systems
Driving 87
Saving current speed 229
SBC 92
SBC brake system 463
Activation 93
Deactivation 94
Driving hints 95
Messages in display 375, 376
Self-check 94
Warning lamp 92
Seat belt force limiter 72