display MERCEDES-BENZ E320 BLUETEC 2007 W211 Workshop Manual

191 Controls in detail
Automatic transmission

Press program mode selector switch
repeatedly until the letter of the
desired program mode appears in the
multifunction display.
SelectCfor comfort driving
(E 63 AMG: for standard driving):

The vehicle starts out in second
gear (both forward and reverse) for
gentler starts. This does not apply if
full throttle is applied or gear
range1 is selected.


Traction and driving stability are
improved on icy roads.


Upshifts occur earlier even when
you give more gas. The engine then
operates at lower rpms and the
wheels are less likely to spin.
SelectSfor standard driving
(E 63 AMG: for sporty driving):


The vehicle starts out in first gear.


Upshifts occur later.Gear selector lever one-touch
gearshifting
With the gear selector lever in drive posi-
tion D and driving in program modeC orS,
you can limit or extend the gear range.
If your vehicle is equipped with manual
shift programM, you can use the gear
selector lever to manually shift the gears.
The following instructions describe opera-
tion of the gear selector lever when driving
in the automatic program modeC orS.Limiting gear range

Briefly press the gear selector lever to
the left in theD-direction.
The transmission will shift to the next
lower gear as permitted by the shift
program. This action simultaneously
limits the gear range of the transmis-
sion (
page 189).
i
For information on using the gear selector
lever in program modeM, see “Manual shift pro-
gram E 63 AMG” (
page 194).
!
Allow engine to warm up under low load use.
Do not place full load on the engine until the
operating temperature has been reached.
Shift into reverse gearR or park positionP only
when the vehicle is stopped.
Avoid spinning of a drive wheel for an extended
period when driving off on slippery road
surfaces. This may cause serious damage to the
drivetrain which is not covered by the
Mercedes-Benz Limited Warranty.
Warning!
G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced
vehicle control. Your vehicle’s ABS will not
prevent this type of loss of control.i
To avoid overrevving the engine when down-
shifting, the transmission will not shift to a lower
gear if the engine’s max. speed would be
exceeded.

192 Controls in detailAutomatic transmissionExtending gear range
Briefly press the gear selector lever to
the right in theD+direction.
The transmission will shift to the next
higher gear as permitted by the shift
program. This action simultaneously
extends the gear range of the transmis-
sion.Canceling gear range limit

Press and hold the gear selector lever
in theD+direction until
D reappears in
the multifunction display (page 186).
The transmission will shift from the
current gear range directly to gear
rangeD.
Shifting into optimal gear range

Press and hold the gear selector lever
in theD-direction.
The transmission will automatically
select the gear range suited for optimal
acceleration and deceleration. This will
involve shifting down one or more
gears.Steering wheel gearshift control
one-touch gearshifting*
Steering wheel gearshift control is avail-
able on vehicles with AMG-Sport Package*
and E 63 AMG only.
With the gear selector lever in drive
positionD and driving in program modeC
orS, you can limit or extend the gear
range.
If your vehicle is equipped with manual
shift programM, you can use the steering
wheel gearshift control to manually shift
the gears.
i
If you press on the accelerator when the en-
gine has reached its rpm limit, the transmission
will upshift beyond any gear range limit selected.
i
For information on using the steering wheel
gearshift control in program modeM, see “Man-
ual shift program E 63 AMG” (
page 194).

194 Controls in detailAutomatic transmissionExtending gear range
Briefly pull right shift paddle2.
The transmission will shift to the next
higher gear as permitted by the shift
program. This action simultaneously
extends the gear range of the transmis-
sion.Canceling gear range limit

Pull and hold right shift paddle2
until
D reappears in the multifunction
display (page 186).
The transmission will shift from the
current gear range directly to gear
rangeD.
Shifting into optimal gear range

Pull and hold left shift paddle1.
The transmission will automatically
select the gear range suited for optimal
acceleration and deceleration. This will
involve shifting down one or more
gears.
Manual shift program E 63 AMG
In addition to the automatic shift
programC orS, your vehicle is equipped
with the manual shift programM.
In the manual program modeM,
system-controlled automatic gearshifting
is switched off and you need to change the
gears by manually upshifting or downshift-
ing using the steering wheel gearshift
paddles (
page 193) or the gear selector
lever.
i
If you press on the accelerator when the en-
gine has reached its rpm limit, the transmission
will upshift beyond any gear range limit selected.
!
Allow engine to warm up under low load use.
Do not place full load on the engine until the
operating temperature has been reached.
Shift into reverse gearR or park positionP only
when the vehicle is stopped.
Avoid spinning of a drive wheel for an extended
period when driving off on slippery road
surfaces. This may cause serious damage to the
drivetrain which is not covered by the
Mercedes-Benz Limited Warranty.

195 Controls in detail
Automatic transmission
The program mode selector switch is
located on the lower part of the center
console.Program mode selector switchM Manual For manual gear shifting
C Comfort For standard driving
S Sport For sporty driving
The selected program mode appears in the
multifunction display (
page 190).Activating manual shift program

Press program mode selector switch
repeatedly until the
M for manual pro-
gram modeM appears in the multifunc-
tion display.
The transmission switches to the
manual program modeM. Automatic
shifting is switched off. The gear range
is not limited.
You can change the gears manually when
the gear selector lever is in drive
positionD. You can upshift or downshift
through the gears in succession.Upshifting

Briefly press the gear selector lever to
the right in theD+direction.
or

Briefly pull right shift paddle2
(page 193).
The transmission shifts to the next
higher gear.
If, instead of the manual program mode
symbolM, thep symbol appears in the
multifunction display (
page 190), shift to
the next higher gear. The fuel supply will
otherwise be interrupted to prevent the
engine from overrevving.
i
For information on automatic program
modesC orS, see “Automatic shift program”
(
page 190), “Gear selector lever one-touch
gearshifting” (
page 191), and “Steering wheel
gearshift control one-touch gearshifting*”
(
page 192).
i
The manual program modeM will not be
stored. When the engine is turned off with the
manual program modeM selected, the transmis-
sion will go to the automatic program mode
(CorS) when the engine is restarted.
!
In the manual program modeM, the trans-
mission will not upshift, even if the engine has
reached its overrevving range. Shift up to the
next gear before the engine has reached its over-
revving range. Make absolutely certain that the
engine speed does not reach the red marking on
the tachometer (
page 26). Otherwise the
engine could be damaged which is not covered
by the Mercedes-Benz Limited Warranty.

196 Controls in detailAutomatic transmissionIf you have selected the AMG menu in the
control system and you are driving in the
manual program modeM, upshift
indicator2 in the multifunction display
advises you to upshift before the engine
reaches the overspeed range. Thus you
can drive at the maximum engine speed for
each gear without overrevving the engine.
1Gear indicator
2Upshift indicator
Shift to the next higher gear.
The fuel supply will otherwise be inter-
rupted to prevent the engine from over-
revving.Downshifting

Briefly press the gear selector lever to
the left in theD-direction.
or

Briefly pull left shift paddle1
(page 193).
The transmission shifts to the next
lower gear.Kickdown
Using the kickdown when driving in the
manual program modeM is not possible.
Deactivating manual shift program

Press the program mode selector
switch (
page 195) repeatedly
until
Cor
S appears in the multifunction
display.
or

Restart the engine.
The transmission will go to the
automatic program mode (C orS).
The manual program modeM is not
stored.
Warning!
G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced
vehicle control. Your vehicle’s ABS will not
prevent this type of loss of control.i
When you brake or stop, the transmission
shifts down to a gear from which you can easily
accelerate or take off.

206 Controls in detailDual-zone automatic climate controlUSA only1
Temperature control, driver’s side
2
Front defroster
3
Increasing air volume
4
Display
5
Air distribution
6
Rear window defroster
7
Temperature control, passenger side
8
MAX COOL on/off
9
AC cooling on/off
a
Climate control on/off
b
Decreasing air volume
c
Air recirculation
d
Air distribution and air volume
(automatic, manual)

207 Controls in detail
Dual-zone automatic climate control
Canada only1
Temperature control, driver’s side
2
Front defroster
3
Increasing air volume
4
Display
5
Air distribution
6
Rear window defroster
7
Temperature control, passenger side
8
Residual heat/ventilation
9
AC cooling on/off
a
Climate control on/off
b
Decreasing air volume
c
Air recirculation
d
Air distribution and air volume
(automatic, manual)

209 Controls in detail
Dual-zone automatic climate control
Deactivating the climate control system
Deactivating
Press button ´ (
page 206) or
(
page 207).
Reactivating

Make sure the ignition is switched on.

Press button ´ (
page 206) or
(
page 207) again.
The previous settings are once again in
effect.Operating the climate control system
in automatic modeActivating

Press buttonU (
page 206) or
(
page 207) while the engine is run-
ning.
The indicators for automatic air volume
and air distribution in display4
(page 206) or (
page 207) come
on. Air volume and air distribution are
automatically controlled.

Use temperature controls1 and7
(page 206) or (
page 207) to sepa-
rately adjust the air temperature on
each side of the passenger compart-
ment.
The temperature of the vehicle interior
is adjusted automatically.
Warning!
G
When the climate control is switched off, the
outside air supply and circulation are also
switched off. Only choose this setting for a
short time. Otherwise the windows could
fog up, impairing visibility and endangering
you and others.
i
To switch the system on, you can also press
another button, with the exception of 1 or
F.
i
When operating the climate control system
in automatic mode, you will only rarely need to
adjust the temperature, air volume and air distri-
bution.
In automatic mode, cooling with dehumidify is
switched on. This function can be switched off.Warning!
G
If you switch off the cooling function the
windows can fog up more quickly. Window
fogging may impair visibility and endanger
you and others.

210 Controls in detailDual-zone automatic climate controlDeactivating
Press button
or Q
(page 206) or (
page 207).
The
AUTO
indicator for air volume in the
display4 (
page 206) or
(
page 207) goes out. The automatic
function for air volume is switched off,
and air volume is controlled according
to the desired setting. Automatic air
distribution remains switched on.
or

Press air distribution button5
(page 206) or (
page 207).
The
AUTO
indicator for air distribution in
the display4 (
page 206) or
(
page 207) goes out. The automatic
function for air distribution is switched
off, and air distribution is controlled ac-
cording to the desired position. Auto-
matic air volume remains switched on.
Setting the temperature
Use temperature controls1 and7
(page 206) or (
page 207) to separate-
ly adjust the air temperature on each side
of the passenger compartment. You
should raise or lower the temperature set-
ting in small increments, preferably start-
ing at 72°F (22°C). The climate control will
adjust to the set temperature as fast as
possible.
Increasing

Turn temperature control1 and/or
7 (
page 206) or (
page 207)
slightly clockwise.
The climate control system will corre-
spondingly adjust the interior air tem-
perature.Decreasing

Turn temperature control1 and/or
7 (
page 206) or (
page 207)
slightly counterclockwise.
The climate control system will corre-
spondingly adjust the interior air tem-
perature.

211 Controls in detail
Dual-zone automatic climate control
Adjusting air distribution
Use air distribution control rocker
switch5 (
page 206) or (
page 207) to
adjust the air distribution.The following symbols are located in the
display4 (
page 206) or (
page 207):

Use air distribution control rocker
switch5 (
page 206) or
(
page 207) until the desired symbol
appears in the display4 (
page 206)
or (
page 207).
The AUTO
indicator for automatic air dis-
tribution in the display4 goes out.
The automatic function for air distribu-
tion is switched off, and air distribution
is controlled according to the desired
setting.
Opening the cockpit air vent (Canada
only) and center air vents

Turn thumbwheels1 and5
(page 204) upward.
The cockpit air vent3 and the center
air vents2 and4 are open.
Symbol
Function
b
Directs air into the entire
vehicle interior
c
Directs air to the windshield,
through the side air vents and
cockpit air vent (Canada only)
Z
Directs air to the windshield
and through the side air vents
X
Directs air to the windshield,
through the side air vents and
to the footwells
a
Directs air through the cockpit
(Canada only), center, side and
rear passenger compartment
air vents
Y
Directs air to the footwells
d
Directs air to the footwells and
through the side air vents
i
The air volume continues to be controlled
according to the indicator in the display4.