Windows MERCEDES-BENZ E350 2006 W211 Owner's Guide

231 Controls in detail
Power windows
Power windows
Opening and closing the windows
The side windows are opened and closed
electrically. The switches for all of the side
windows are on the driver’s door. The
switches for the respective windows are
on the front passenger door and the rear
doors.
1Rear window override switch
(
page 89)
2Right front window
3Right rear window
4Left rear window
5Left front window
Warning!
G
When closing the windows, make sure that
there is no danger of anyone being harmed
by the closing procedure.
The closing of the door windows can be im-
mediately halted by releasing the switch or,
if switch was pulled past the resistance
point and released, by either pressing or
pulling the respective switch.
The door windows are equipped with the ex-
press-close and automatic reversal func-
tion. If the window encounters an
obstruction that blocks its path in a circum-
stance where you pulled the switch past the
resistance point and released it to close the
window, the automatic reversal function will
stop the window and open it slightly.
If the window encounters an obstruction
that blocks its path in a circumstance where
you are closing the window by pulling and
holding the switch, by pressing and holding
button ‹ on the SmartKey, by pressing
and holding the lock button (vehicles with
KEYLESS-GO*) on an outside door handle,
or by pressing and holding button, on
the climate control panel, the automatic re-
versal function will not operate.
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. Unsupervised use of vehi-
cle equipment can cause an accident
and/or serious personal injury.

232 Controls in detailPower windows

Switch on the ignition (
page 36).
Opening the windows

Press switch2 to 5 to the resistance
point.
The corresponding window will move
downwards until you release the
switch.Closing the windows

Pull switch2 to 5 to the resistance
point.
The corresponding window will move
upwards until you release the switch.
Fully opening the windows
(Express-open)

Press switch2 to 5 past the resis-
tance point and release.
The corresponding window opens com-
pletely.
iYou can also open or close the win-
dows using the SmartKey, see “Sum-
mer opening feature” (
page 234) and
“Convenience closing feature”
(
page 235).
Depending on current position, the win-
dows may also open or close when the
air recirculation button, in the
control panel of the climate control
(page 204), (
page 216) and
(
page 217) is pressed and held.
iOperating the windows from the rear is
not possible if you activate the override
switch (
page 89).
iWith the SmartKey in starter switch po-
sition 0 or removed from the starter
switch, the power windows can be op-
erated:

until you open the driver’s or front
passenger’s door


for at least 5 minutes.
Warning!
G
If you pull and hold the switch up when clos-
ing the window, and upward movement of
the window is blocked by some obstruction
including but not limited to arms, hands, fin-
gers, etc., the automatic reversal will not op-
erate.

233 Controls in detail
Power windows
Fully closing the windows
(Express-close)
Pull switch2 to 5 past the resis-
tance point and release.
The corresponding window closes com-
pletely.
Stopping windows during Express-op-
eration

Press or pull the respective power win-
dow switch again.
Synchronizing power windows
The power windows must be synchronized

after the battery has been disconnect-
ed


if the power windows cannot be fully
opened (Express-open) or closed
(Express-close)
Synchronizing

Close all doors.

Switch on the ignition (
page 36).

Pull switch2 to 5 until the side win-
dows are completely closed.

Hold on to switches2 to 5 for ap-
proximately 1 second.
The power windows are synchronized.
Warning!
G
Driver’s door only:
If within 5 seconds switch is again pulled
past the resistance point and released, the
automatic reversal will not operate.
!If the upward movement of the window
is blocked during the closing proce-
dure, the window will stop and open
slightly.
Remove the obstruction, pull the re-
spective power window switch again
past the resistance point and release.
If the window still does not close when
there is no obstruction, pull and hold
the respective power window switch.
The side window will then close without
the obstruction sensor function.

234 Controls in detailPower windowsSummer opening feature
If the weather is warm, you can ventilate
the vehicle before driving off by simulta-
neously:

opening the side windows


opening the tilt/sliding sunroof* or
tilt/sliding panel*


turning on the seat ventilation* for the
driver’s seat

Aim transmitter eye of the SmartKey or
SmartKey with KEYLESS-GO* at the
driver’s outside door handle. The
SmartKey or SmartKey with
KEYLESS-GO* must be in close proxim-
ity to the driver’s outside door handle.
Vehicles without panorama roof*

Press and hold button
Œ
until the
windows and the tilt/sliding sunroof*
have reached the desired position.

Release button
Œ
to interrupt proce-
dure.Vehicles with panorama roof*
If roller sunblinds are closed:

Press and hold button
Œ
. The win-
dows and roller blinds begin to open af-
ter approximately 1 second.

With the windows and roller blinds fully
opened, press and hold button
Œ

again. The tilt/sliding panel of the pan-
orama roof* tilts and opens.
If roller sunblinds are open:

Press and hold button
Œ
. The win-
dows move down and the tilt/sliding
panel tilts and opens after approxi-
mately 1 second.

Release button
Œ
to interrupt proce-
dure.
iThe seat ventilation* for the driver’s
seat is automatically set to the highest
level if activated via summer opening
feature.

235 Controls in detail
Power windows
Convenience closing feature
When you lock the vehicle, you can close
the windows, tilt/sliding sunroof* or
tilt/sliding panel* simultaneously.
Aim transmitter eye of the SmartKey or
SmartKey with KEYLESS-GO* at the
driver’s outside door handle
(page 234). The SmartKey or
SmartKey with KEYLESS-GO* must be
in close proximity to the driver’s out-
side door handle.

Press and hold button ‹ until the
windows, the tilt/sliding sunroof* or
tilt/sliding panel* are completely
closed.
Vehicles with panorama roof*:

Press and hold button ‹ again. The
roller sunblinds close.

Release button ‹ to interrupt pro-
cedure.Vehicles with KEYLESS-GO*:

Press and hold the lock button on an
outside door handle (
page 64) until
the windows, the tilt/sliding sunroof*
or tilt/sliding panel* are completely
closed.

Release the lock button on the outside
door handle to interrupt procedure.
Warning!
G
When closing the side windows and the
tilt/sliding sunroof* or tilt/sliding panel*,
ma ke s ur e th at th er e is no dan ge r o f an y o ne
being harmed by the closing procedure.
If potential danger exists, proceed as fol-
lows:

Release button ‹ to stop the closing
procedure. To open, press and hold
buttonŒ. To continue the closing
procedure after making sure that there
is no danger of anyone being harmed by
the closing procedure, press and hold
button‹.
Vehicles with KEYLESS-GO*:


Release the lock button (
page 64) on
the outside door handle to stop the clos-
ing procedure.


Pull on the outside door handle and hold
firmly. The side windows and the
tilt/sliding sunroof* or tilt/sliding pan-
el* will open for as long as the door han-
dle is held but the door not opened.

353 Operation
Tires and wheels
Tire ply material
1Plies in sidewall
2Plies under tread
This marking tells you about the type of
cord and number of plies in the sidewall
and under the tread.
Tire and loading terminology
Accessory weight
The combined weight (in excess of those
standard items which may be replaced) of
automatic transmission, power steering,
power brakes, power windows, power
seats, radio, and heater, to the extent that
these items are available as
factory-installed equipment (whether
installed or not).
Air pressure
The amount of air inside the tire pressing
outward on each square inch of the tire.
Air pressure is expressed in pounds per
square inch (psi), or kilopascal (kPa) or
bar.
Aspect ratio
Dimensional relationship between tire
section height and section width
expressed in percentage.
Warning!
G
The temperature grade for this tire is estab-
lished for a tire that is properly inflated and
not overloaded. Excessive speed, underin-
flation, or excessive loading, either sepa-
rately or in combination, can cause
excessive heat build-up and possible tire
failure.
iFor illustration purposes only. Actual
data on tires are specific to each vehi-
cle and may vary from data shown in
above illustration.

364 OperationVehicle careCleaning and care of vehicle
While in operation, even while parked, your
vehicle is subjected to varying external in-
fluences which, if gone unchecked, can at-
tack the paintwork as well as the vehicle
underbody and cause lasting damage.Such damage is caused not only by ex-
treme and varying climatic conditions, but
also by:


Air pollution


Road salt


Tar


Gravel and stone chipping
To avoid paint damage, you should imme-
diately remove:


Grease and oil


Fuel


Coolant


Brake fluid


Bird droppings


Insects


Tree resins etc.
Frequent washing reduces and/or elimi-
nates the aggressiveness and potency of
the above adverse influences.More frequent washings are necessary to
deal with unfavorable conditions:


near the ocean


in industrial areas (smoke, exhaust
emissions)


during winter operation
You should check your vehicle from time to
time for stone chipping or other damage.
Any damage should be repaired as soon as
possible to prevent corrosion.
In doing so, do not neglect the underbody
of the vehicle. A prerequisite for a thor-
ough check is a washing of the underbody
followed by a thorough inspection. Dam-
aged areas need to be re-undercoated.
Your vehicle has been treated at the facto-
ry with a wax-base rustproofing in the body
cavities which will last for the lifetime of
the vehicle. Post-production treatment is
neither necessary nor recommended by
Mercedes-Benz because of the possibility
of incompatibility between materials used
in the production process and others ap-
plied later.
Warning!
G
Many cleaning products can be hazardous.
Some are poisonous, others are flammable.
Always follow the instructions on the partic-
ular container. Always open your vehicle’s
doors or windows when cleaning the inside.
Never use fluids or solvents that are not de-
signed for cleaning your vehicle.
Always lock away cleaning products and
keep them out of reach of children.

369 Operation
Vehicle care
Cleaning the windows and the wiper
blades
Switch on the ignition (
page 36).

Turn combination switch to wiper
settingII (
page 56).

With wiper arms in vertical position,
switch off the ignition (
page 62).

Fold the wiper arms forward until they
snap into place.

Clean the wiper blade inserts with a
clean cloth and detergent solution.

Use a soft, clean cloth and a mild win-
dow cleaning solution on all outside
and inside glass surfaces.
An automotive glass cleaner is recom-
mended.
!The windshield wipers must be in a ver-
tical position before folding them away
from the windshield. They could other-
wise damage the hood.
Never open the hood when the wiper
arms are folded forward.
Warning!
G
For safety reasons, switch off wipers and re-
move SmartKey from starter switch (vehi-
cles with KEYLESS-GO*: Make sure the
vehicle’s on-board electronics have
status0) before cleaning the windshield the
windshield and/or the wiper blades. Other-
wise, the wiper motor could suddenly turn
on and cause injury.
!Fold the windshield wiper arms back
onto the windshield before turning the
SmartKey in the starter switch or
pressing the KEYLESS-GO start/stop
button (vehicles with KEYLESS-GO*).
Hold on to the wiper when folding the
wiper arm back. If released, the force
of the impact from the tensioning
spring could crack the windshield.!To clean the window interior, do not
use a dry cloth, abrasives, solvents or
cleaners containing solvents. Do not
touch the inside of the front, rear or
side windows with hard objects such as
an ice scraper or ring. Doing so may
damage the windows.

453 Practical hints
Batteries
Reconnecting the battery
Turn off all electrical consumers.

Remove SmartKey from starter switch.

Connect the positive lead and fasten its
cover.

Connect the negative lead.

Install the luggage box (
page 423).
Batteries contain materials that can harm
the environment if disposed of improperly.
Large 12 volt storage batteries contain
lead. Recycling of batteries is the preferred
method of disposal. Many states require
sellers of batteries to accept old batteries
for recycling.
!Never invert the terminal connections!
iThe following procedures must be car-
ried out following any interruption of
battery power (e.g. due to reconnec-
tion):

Set the clock (
page 168)
(see COMAND operator’s manual).


Resynchronize the ESP
®
(
page 391).


Resynchronize the side windows
(page 233).


Resynchronize the tilt/sliding sun-
roof* (
page 238) or the tilt/slid-
ing panel* (
page 242).

509 Index
K
Key, Mechanical 426
Key, SmartKey
Battery check lamp 106
Changing batteries 431
Factory setting 108
Locking/unlocking 34
Locking/unlocking, Global
setting 108
Locking/unlocking, Selective
setting 108
Loss of 110
Messages in display 411
Opening and closing the power
tilt/sliding sunroof* or panorama
roof with power tilt/sliding
panel* 234
Opening and closing the
windows 234
Positions in starter switch 36
Remote control 106
Starting the engine 50
Turning off engine 62Key, SmartKey with KEYLESS-GO*
Battery check lamp 111
Changing batteries 431, 432
Factory setting 114
Locking, Trunk lid 114
Locking/unlocking 35
Locking/unlocking, Selective
setting 115
Loss of 118
Messages in display 410
Opening and closing the the power
tilt/sliding sunroof* or panorama
roof with power tilt/sliding
panel* 234
Opening and closing the
windows 234
Starting the engine 51
Turning off engine 62
Unlocking, Trunk lid 118
KEYLESS-GO* 495
KEYLESS-GO* see Key, SmartKey with
KEYLESS-GO*
Kickdown 186, 495
Kilopascal 354L
Labels
Certification 468
Emission control information 468
Emission control vacuum line
routing 468
Lamp sensor
Message in display 414
Lamps, exterior
Light sensor 414
Messages in display 412, 413, 414,
415
Lamps, indicator and warning
ABS 25, 374
Battery (SmartKey) 108, 115
Brakes 376
CHECK ENGINE 377, 378
Coolant 379
Distance warning lamp* 250
Electrohydraulic brake system 97
Engine diagnostics 377, 378
Engine malfunction 25, 377, 378
ESP
®
25, 375
Fog lamps 144
Front passenger front air bag off 27,
72, 384, 385