oil MERCEDES-BENZ E500 2004 W211 Owner's Guide

373 Practical hints
Flat tire
Mounting the Minispare wheel
Clean contact surfaces of wheel and
wheel hub.

Guide the spare wheel onto the align-
ment bolt and push it on.

Insert wheel bolts and tighten them
slightly.

Unscrew the alignment bolt, install last
wheel bolt and tighten slightly.
!To avoid paint damage, place wheel flat
against hub and hold it there while in-
stalling first wheel bolt.
Warning!
G
Always replace wheel bolts that are dam-
aged or rusted.
Never apply oil or grease to wheel bolts.
Damaged wheel hub threads should be re-
paired immediately. Do not continue to drive
under these circumstances! Contact an au-
thorized Mercedes-Benz Center or call
Roadside Assistance.
Incorrect wheel bolts or improperly tight-
ened wheel bolts can cause the wheel to
come off. This could cause an accident. Be
sure to use the correct wheel bolts.
Warning!
G
Use only genuine equipment
Mercedes-Benz wheel bolts. They are identi-
fied by the Mercedes star. Other wheel bolts
may come loose.
Do not tighten the wheel bolts when the ve-
hicle is raised. Otherwise the vehicle could
tip over.

400 Technical dataFuels, coolants, lubricants etc.
Fuels, coolants, lubricants etc.CapacitiesVehicle components and their respective
lubricants must match. Therefore use only
brands tested and approved by us.Please refer to the Factory Approved Ser-
vice Products Pamphlet, or inquire at your
authorized Mercedes-Benz Center.
Model
Capacity
Fuels, coolants, lubricants etc.
Engine with oil filter
E 320 / E 320 4MATIC
8.5 US qt (8.0 l)
Approved engine oils
E 500 / E 500 4MATIC
8.0 US qt (7.5 l)
E55AMG
9.0 US qt (8.5 l)
Automatic transmission
8.0 US qt (7.5 l)
MB Automatic Transmission Oil
Front axle
E3204MATIC /
E5004MATIC
0.63 US qt (0.6 l)
Hypoid gear oil SAE 85 W 90
Rear axle
E 320 / E 320 4MATIC
1.06 US qt (1 l)
Hypoid gear oil SAE 85 W 90
E 500 / E 500 4MATIC/
E55AMG
1.37 US qt (1.3 l)
Transfer case
E3204MATIC /
E5004MATIC
0.62 US qt (0.585 l)
MB Transfer Case Fluid

402 Technical dataFuels, coolants, lubricants etc.
Model
Capacity
Fuels, coolants, lubricants etc.
Air conditioning system
R-134a refrigerant and special PAG lu-
bricant oil (never R-12)
Windshield washer
4.8 US qt (4.5 l)
MB Windshield Washer Concentrate
1
1Use MB Windshield Washer Concentrate “S” and water for temperatures above freezing or MB Windshield Washer Concentrate “S” and commercially available pre-
mixed windshield washer solvent / antifreeze for temperatures below freezing point. Follow suggested mixing ratios (page 407).Windshield washer and headlamp cleaning
system
7.4 US qt (7.0 l)
MB Windshield Washer Concentrate
1

403 Technical data
Fuels, coolants, lubricants etc.
Engine oils
Engine oils are specifically tested for their
suitability in our engines. Therefore, use
only engine oils recommended by
Mercedes-Benz. Information on recom-
mended brands is available in the Factory
Approved Service Products Pamphlet, or at
your authorized Mercedes-Benz Center.Please follow FSS recommendations for
scheduled oil changes. Failure to do so
could result in engine damage not covered
by the Mercedes-Benz Limited Warranty.
Engine oil additives
Do not blend oil additives with engine oil.
They may damage the engine.
Damage or malfunctions resulting from
blending oil additives are not covered by
the Mercedes-Benz Limited Warranty.Air conditioning refrigerant
R-134a (HFC) refrigerant and special PAG
lubricating oil is used in the air condition-
ing system.Never use R-12 (CFC) or mineral-based lu-
bricating oil. Otherwise damage to the
system will occur.
Brake fluid
During vehicle operation, the boiling point
of the brake fluid is continuously reduced
through the absorption of moisture from
the atmosphere. Under extremely strenu-
ous operating conditions, this moisture
content can lead to the formation of bub-
bles in the system, thus reducing the sys-
tem’s efficiency.
Therefore, the brake fluid must be re-
placed every two years, preferably in the
spring.
Only brake fluid approved by
Mercedes-Benz is recommended. Your au-
thorized Mercedes-Benz Center will pro-
vide you with additional information.
!Always check the oil filler cap
(page 285) for important information
pertaining to the engine oil needing to
meet a specific Mercedes-Benz specifi-
cation (e.g. MB 229.5). If such informa-
tion is printed on the oil filler cap, only
use an engine oil from the list of ap-
proved engine oils in the Factory Ap-
proved Service Products pamphlet that
meets the specification indicated on
the oil filler cap.
Using engine oils of other specification
may cause the FSS to incorrectly deter-
mine the next service interval and will
result in engine damage not covered by
the Mercedes-Benz Limited Warranty.

404 Technical dataFuels, coolants, lubricants etc.Premium unleaded gasoline
Fuel requirements
Use only premium unleaded gasoline
meeting ASTM standard D 439:

The octane number (posted at the
pu mp ) m ust b e 91 m i n. It is an a ve ra ge
of both the Research (R) Octane Num-
ber and the Motor (M) Octane Number:
(R+M) / 2). This is also known as the
ANTI-KNOCK INDEX.
Unleaded gasoline containing oxygenates
such as ethanol, IPA, IBA and TBA can be
used provided the ratio of any one of these
oxygenates to gasoline does not exceed
10%; MTBE must not exceed 15%.
The ratio of methanol to gasoline must not
exceed 3% plus additional cosolvents.
Using mixtures of ethanol and methanol is
not allowed. Gasohol, which contains 10%
ethanol and 90% unleaded gasoline, can be
used.
These blends must also meet all other fuel
requirements, such as resistance to spark
knock, boiling range, vapor pressure, etc.
Gasoline additives
A major concern among engine manufac-
turers is carbon build-up caused by gaso-
line. Mercedes-Benz recommends only the
use of quality gasoline containing additives
that prevent the build-up of carbon depos-
its.
After an extended period of using fuels
without such additives, carbon deposits
can build up especially on the intake valves
and in the combustion area, leading to en-
gine performance problems such as:

Warm-up hesitation


Unstable idle


Knocking / pinging


Misfire


Power loss
Do not blend any specific fuel additives
with fuel. This only results in unnecessary
costs and may be harmful to the engine op-
eration.
!To maintain the engine’s durability and
performance, premium unleaded gaso-
line must be used. If premium unleaded
gasoline is not available and low octane
fuel is used, follow these precautions:

Have the fuel tank only partially
filled with unleaded regular and fill
up with premium unleaded as soon
as possible


Avoid full throttle driving and abrupt
acceleration


Do not exceed an engine speed of
3000 rpm if the vehicle is loaded
with a light load such as two per-
sons and no luggage


D o n o t e x c e e d 2 / 3 o f m a x i m u m a c -
celerator pedal position if the vehi-
cle is fully loaded or operating in
mountainous terrain

405 Technical data
Fuels, coolants, lubricants etc.
Damage or malfunctions resulting from
poor fuel quality or from blending specific
fuel additives are not covered by the
Mercedes-Benz Limited Warranty.Coolants
The engine coolant is a mixture of water
and anticorrosion / antifreeze, which pro-
vides:

Corrosion protection


Freeze protection


Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory
with a coolant providing freeze protection
to approximately -22°F (-30°C) and corro-
sion protection.If the antifreeze mixture is effective to
-22°F (-30°C), the boiling point of the cool-
ant in the pressurized cooling system is
reached at approximately 266°F (130°C).
The coolant solution must be used
year-round to provide the necessary corro-
sion protection and increase boil-over pro-
tection. Refer to Service Booklet for
replacement interval
Coolant system design and coolant used
stipulate the replacement interval. The re-
placement interval published in the Ser-
vice Booklet is only applicable if MB 325.0
anticorrosion/antifreeze solution or other
Mercedes-Benz approved products of
equal specification (see Factory Approved
Service Products pamphlet) are used to re-
new the coolant concentration or bring it
back up to the proper level. To provide important corrosion protection,
the solution must be at least 45%
anticorrosion / antifreeze [equivalent to
freeze protection to approximately - 22°F
(-30°C)]. If you use a solution that is more
than 55% anticorrosion / antifreeze [freeze
protection to approximately - 49°F
(-45°C)], the engine temperature will in-
crease due to the lower heat transfer capa-
bility of the solution. Therefore, do not use
more than this amount of
anticorrosion / antifreeze.

412 Technical termsCOMAND
(C
ockpit M
anagement and D
ata Sys-
tem)
Information and operating center for
vehicle sound and communications
systems, including the radio and navi-
gation system, as well as other optional
equipment (CD changer, telephone,
etc.).
Control system
The control system is used to call up
vehicle information and to change
component settings. Information and
messages appear in the multifunction
display. The driver uses the buttons on
the multifunction steering wheel to
navigate through the system and to ad-
just settings.
Cruise control
Driving convenience system for auto-
matically maintaining the vehicle speed
set by the driver.Distronic*
A driving convenience cruise control
system which helps the driver maintain
a pre-selected speed:


If there is no vehicle directly ahead,
the system operates in the same
way as conventional ->cruise con-
trol.


If a slower moving vehicle is ahead,
Distronic will reduce your vehicle
speed to the extent permitted by re-
duced throttle and up to 20% brak-
ing power to maintain the preset
minimum following distance.
DTR
(->Distronic*)
Engine number
The number set by the manufacturer
and placed on the cylinder block to
uniquely identify each engine pro-
duced.Engine oil viscosity
Measurement for the inner friction (vis-
cosity) of the oil at different tempera-
tures. The higher the temperature an
oil can tolerate without becoming thin,
or the lower the temperature it can tol-
erate without becoming viscous, the
better the viscosity.
ESP
(E
lectronic S
tability Pr
ogram)
Improves vehicle handling and direc-
tional stability.
ETD
(E
mergency T
ensioning D
evice)
Device which deploys in certain frontal
and rear collisions exceeding the sys-
tem's threshold to tighten the seat
belts.
->SRS
FSS PLUS
(F
lexible S
ervice S
ystem PLUS)
Service indicator in the multifunction
display that informs the driver when
the next vehicle maintenance service is
due.

417 Index
A
ABS 74, 411
ABS control 75
Malfunction indicator lamp 310
Messages in display 319
Warning lamp 310
Accelerator position, automatic
transmission 164
Accident
In case of 50
Activating
Air conditioning (cooling) 182, 194
Air recirculation mode 180, 191
Anti-theft alarm system 84
Automatic climate control 186
Central locking (control system) 149
Charcoal filter 192
Climate control 176
Defrosting 179
Distance warning function* 223
Distronic* 219
Easy-entry/exit feature* 150
ESP 79
Exterior headlamps 47
Exterior lamps 120Front fog lamps 122
Hazard warning flasher 124
Headlamps 47
High beams 123
Ignition 31
Ignition with KEYLESS-GO* 33
Immobilizer 53, 83
Rear fog lamp 121, 122
Rear window defroster 173
Residual heat 182, 194
Seat heater* 113
Tow-away alarm 85
Windshield wipers 48
Adding
Engine oil 284
Additional turn signal 359
Adjustable air vents, rear passenger
compartment 195
Adjusting 34
Air distribution 178, 189
Air volume 178, 179, 190
Backrest tilt 36
Exterior rear view mirror 38
Head restraint height 36
Head restraint tilt 36Instrument cluster illumination 126
Interior rear view mirror 38
Mirrors 38
Multicontour seat* 111
Seat cushion depth 111
Seat cushion tilt 36
Seat fore and aft adjustment 35
Seat height 36
Seats 34
Steering column height 37
Steering wheel 37
Adjusting steering column in or out 37
Adjusting steering column up or down 37
Adjusting the dynamic seat 153
Air conditioning (cooling)
Turning off 182, 194
Turning on 182, 194
Air distribution
Adjusting 178, 189
Air pressure see Tire inflation
pressure 290
Air recirculation mode 180, 191
Activating 180, 191
Deactivating 181, 192

420 IndexC
CAC (Customer Assistance Center) 411
Calling up
Distronic* settings 136
Range (distance to empty) 154
Service indicator 298
CAN system 411
Cargo tie-down rings 241
CD player
Operating 135
Center console
Lower part 26
PASSENGER AIRBAG OFF indicator
lamp 317
Upper part 25
Centigrade
Setting temperature units 141
Central locking
Automatic 106
From inside 107
Switch 107
Switching on/off (control
system) 149
Unlocking from inside 107Central locking switch 107
Changing
Batteries (SmartKey with
KEYLESS-GO*) 355, 356
Batteries (SmartKey) 355, 356
Smartkey setting 150
Vehicle level 228
Charcoal filter 192
Activating 192
Deactivating 193
Charging
Vehicle batteries 377
CHECK ENGINE malfunction indicator
lamp 313
Checking
Coolant level 285
Oil level 279, 282
Tire inflation pressure 279
Vehicle lighting 279
Child safety 65
Airbags 58
Infant and child restraint systems 62,
65
LATCH child seat anchors 71Child safety switch see Blocking of rear
window operation 72
Cigarette lighter 247
Cleaning
Headlamps 170
Light alloy wheels 305
Parktronic* system sensor 305
Windshield 49
Wood trims 308
Climate control 174
Adjusting 178
Defrosting 179
Setting the temperature 178
Clock 144
Closing
Glove box 242
Panorama sliding/pop-up roof 206
Panorama sliding/pop-up roof with
KEYLESS-GO* 209
Panorama sliding/pop-up roof* with
KEYLESS-GO* 200
Roller sunblinds 205
Side windows 198

424 IndexElectronic Stability Program see ESP 76,
412
Emergency call system* 250
Emergency calls
Initiating an emergency call 253
With Tele Aid* 252
Emergency operation (Limp Home
Mode) 167
Opening/closing Sliding/pop-up roof*
or panorama sliding/pop-up
roof* 358
Releasing trunk lid from inside 104
Emergency operations
Remote door unlock 257
Unlocking the trunk lid 354
Unlocking the vehicle 353
Emergency tensioning device see
ETD 64, 412
Emission control 276
Ending
A call (telephone) 156Engine 392
Compartment 281
Message in the display 313
Starting 43
Starting with KEYLESS-GO* 44
Starting with the SmartKey 44
Turning off with the key 53
Engine compartment
Hood 281
Engine malfunction indicator lamp 313
Engine number 412
Engine oil
Adding 284
Additives 403
Checking level 282
Consumption 282
Display messages 333
Filler neck 285
Messages in display 283
Viscosity 412
Entry position
Messages in the display 347ESP 76, 412
Four wheel electronic traction system
with ESP 82
Switching off 78
Switching on 79
Synchronizing 323
Warning lamp 311
ETD 412
Safety guidelines 60
Exterior lamp switch 119
Exterior rear view mirrors
Adjusting 38
Parking position for 152
F
Fahrenheit
Setting temperature units 141
Fastening the seat belts 40
Fine adjustment
Cruise control 213
First aid kit 350
Flat tire 366
Mounting the spare wheel 370
Spare wheel 370
Flexible 297