MMI MERCEDES-BENZ E500 2004 W211 Owner's Manual

258 Controls in detailUseful featuresStolen vehicle tracking services
In the event your vehicle was stolen:
Report the incident to the police.
The police will issue a numbered inci-
dent report.

Pass this number on to the
Mercedes-Benz Response Center along
with your password issued to you when
you subscribed to the service.
The Response Center will then attempt
to covertly contact the vehicle’s
Tele Aid system. Once the vehicle is lo-
cated, the Response Center will con-
tact the local law enforcement and you.
The vehicle’s location will only be pro-
vided to law enforcement.
Garage door opener
The built-in remote control is capable of
operating up to three separately controlled
devices, for example garage door openers,
gate openers, or other devices compatible
with HomeLink
® or some other systems.
You can program the signal transmitter
buttons.
123Signal transmitter key
4Indicator lamp
5Hand-held transmitter button
6Hand-held remote control trans-
mitter (not part of the vehicle
equipment)
Warning!
G
Before programming the integrated remote
control to a garage door opener or gate op-
erator, make sure that people and objects
are out of the way of the device to prevent
potential harm or damage.
When programming a garage door opener,
the door moves up or down. When program-
ming a gate operator, the gate opens or
closes.
Do not use the integrated remote control
with any garage door opener that lacks safe-
ty stop and reverse features as required by
U.S. federal safety standards (this includes
any garage door opener model manufac-
tured before April 1, 1982). A garage door
that cannot detect an object - signaling the
door to stop and reverse - does not meet
current U.S. federal safety standards.

259 Controls in detail
Useful features
Programming or reprogramming the in-
tegrated remote control
Step 1:
Switch on ignition.
Step 2:

If you have previously programmed an
integrated signal transmitter button
and wish to retain its programming,
proceed to step 3. Otherwise, press
and hold the two outer signal transmit-
ter buttons1 and3 and release
them only when the indicator light be-
gins to flash after approximately 20
seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory. If you later wish to program a
second and/or third hand-held trans-
mitter to the remaining two signal
transmitter buttons, do not repeat this
step and begin directly with step 3.
iCertain types of garage door openers
are incompatible with the integrated
opener. If you should experience diffi-
culties with programming the transmit-
ter, contact your authorized
Mercedes-Benz Center, or call
Mercedes-Benz Customer Assistance
Center (in the USA only) at
1-800-FOR-MERCedes, or Customer
Service (in Canada) at
1-800-387-0100.
iFor operation in the USA only:
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any inter-
ference received, including interfer-
ence that may cause undesired
operation.
Any unauthorized modification to this
device could void the user’s authority
to operate the equipment.


260 Controls in detailUseful featuresStep 3:
Hold the end of the hand-held remote
control transmitter6 of the device
you wish to train approximately 2 to
5 in (5 to12 cm) away from the surface
of the integrated remote control locat-
ed on the interior rear view mirror,
keeping the indicator lamp4 in view.
Step 4:

Using both hands, simultaneously
press the hand-held transmitter
button5 and the desired integrated
signal transmitter button (1, 2
or3). Do not release the buttons until
completing step 5.
The indicator lamp4 on the integrat-
ed remote control will flash, first slowly
and then rapidly.Step 5:

When the indicator lamp4 flashes
rapidly, release both buttons.
Step 6:

Press and hold the just-trained inte-
grated signal transmitter button and
observe the indicator lamp4.
If the indicator lamp4 stays on con-
stantly, programming is complete and
your device should activate when the
integrated signal transmitter button is
pressed and released.Step 7:

To program the remaining two buttons,
repeat the steps above starting with
step 3.
iThe indicator lamp4 flashes the first
time the signal transmitter button is
programmed. If this button has already
been programmed, the indicator lamp
will only start flashing after 20 sec-
onds.
iIf the indicator lamp4 blinks rapidly
for about two seconds and then turns
to a constant light, continue with pro-
gramming steps 8 through 12 as your
garage door opener may be equipped
with the “rolling code” feature.


261 Controls in detail
Useful features
Rolling code programming
To train a garage door opener (or other roll-
ing code devices) with the rolling code fea-
ture, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
Step 8:
Locate “training” button on the garage
door opener motor head unit.
Exact location and color of the button
m a y v a r y b y g a r a g e d o o r o p e n e r b r a n d .
Depending on manufacturer, the “train-
ing” button may also be referred to as
“learn”or “smart” button. If there is dif-
ficulty locating the transmitting button,
refer to the garage door opener opera-
tor’s manual. Step 9:

Press “training” button on the garage
door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the follow-
ing step.
Step 10:

Firmly press, hold for two seconds and
release the programmed integrated
signal transmitter button (1, 2
or3).
Step 11:

Press, hold for two seconds and re-
lease same button a second time to
complete the training process.
Some garage door openers (or other rolling
code equipped devices) may require you to
perform this procedure a third time to
complete the training.Step 12:

Confirm the garage door operation by
pressing the programmed integrated
signal transmitter button (1, 2
or3).
Step 13:

To program the remaining two buttons,
repeat the steps above starting with
step 3.

262 Controls in detailUseful featuresGate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the inte-
grated signal transmitter to pick up the sig-
nal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having dif-
ficulties programming a gate operator (re-
gardless of where you live) by using the
programming procedures, replace step 4
with the following:Step 4:

Continue to press and hold the inte-
grated signal transmitter button (1,
2 or3) while you press and re-press
(“cycle”) your hand-held remote con-
trol transmitter6 every two seconds
until the frequency signal has been
learned. Upon successful training, the
indicator lamp4 will flash slowly and
then rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete. Operation of integrated remote control

Switch on ignition.

Select and press the appropriate inte-
grated signal transmitter button (1,
2 or3) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.

263 Controls in detail
Useful features
Erasing the integrated remote control
memory
Switch on ignition.

Simultaneously hold down the signal
transmitter buttons1 and 3, for ap-
proximately 20 seconds, until the indi-
cator lamp4 blinks rapidly. Do not
hold for longer than 30 seconds.
The codes of all three channels are
erased.Reprogramming a single integrated
signal transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:

Press and hold the desired signal trans-
mitter button (1, 2 or3). Do not re-
lease the button.

The indicator lamp will begin to flash af-
ter 20 seconds. Without releasing the
integrated signal transmitter button,
proceed with programming starting
with step 3.
iIf you sell your vehicle, erase the codes
of all three channels.

425 Index
Flexible Service System (FSS) 297, 412
Fog lamp, rear 122
Fog lamps, front 122
Messages in display 337
Replacing bulbs 359
Switching on 122
Following distance in Distronic* 221
Four wheel electronic traction system
(4MATIC) with ESP 82
4MATIC 82
Front airbags 61
Front lamps 359
Messages in display 338
Replacing bulbs 361
Switching on 119
Front seat head restraints
Power seat 109
removing and installing 109
Front seats
Heater* 113
FSS (Flexible Service System) 297, 412
Fuel 279
Fuel tank reserve warning lamp 315
Premium unleaded gasoline 279Fuel consumption statistics
After start 153
Since last reset 154
Fuel filler flap 278
Locking 278
Unlocking 278
Fuel reserve tank
Message in display 335
Fuel tank
Filler flap 278
Fuels, coolants, lubricants etc. 400
Fully closing (Express-close) the slid-
ing/pop-up roof 202
Fully opening (Express-open) the slid-
ing/pop-up roof 202
Functions (control system) 133
Resetting 139
Fuse chart 385
Fuses 385
Fuse chart 385
Fuse extractor 385
Spare fuses 385G
Garage door opener 27, 258
Erasing the integrated remote
control 263
Integrated remote control 259
Rolling code programming 261
Gasoline see Fuel 279
Gear range 413
Automatic transmission 160
Limiting 160
Shifting into optimal 159
Gear range limit
Canceling 159
Gear selector lever
Position 161
Global
Locking 89
Locking with KEYLESS-GO* 94
Unlocking 89
Unlocking with KEYLESS-GO* 94
Global Positioning System (GPS) 413
Glove box 242
Closing 242
Opening 242
Good visibility 168

426 IndexGPS 413
GPS see COMAND 251
H
Hand-held transmitter
Programming integrated remote
control 259
Reprogramming integrated remote
control 263
Hazard warning flasher 123
Switching off 124
Switching on 124
Headlamps
Automatic control 120
Bi-Xenon* 411
Cleaning system* 170
Switching off 52
Switching on 47
Headlamps, tail lamps, side markers, turn
signal lenses 304
Heated seats* 113
Heated steering wheel* 248
Height adjustment
Head restraints 36
Steering wheel 37
Vehicle level 227High beam flasher 47, 123
High beam headlamps
Messages in display 338
Replacing bulbs 359
Switching on 123
Hood 281
Closing 281
Message in display 335
Opening 281
Hydroplaning 271
I
Identification labels 390
Ignition 31, 33
Switching on 44
Immobilizer 83
Activating 83
Deactivating 83
Indicator lamps see Lamps, indicator and
warning
Infant and child restraint systems 65
Installing 69
LATCH child seat anchors 71Information
About service and warranty 10
Button for Tele Aid* 255
Inside rear view mirror
Antiglare 168
Installing
Infant and child restraint systems 69
Towing eye bolt 384
Wiper blades 365
Instrument cluster 22, 126, 307, 413
Coolant temperature gauge 127
Illumination 126
Multifunction display 129
Outside temperature indicator 128
Selecting language 142
Instrument lighting 126, 127
Integrated remote control
Canadian programming 262
Erasing memory 263
Gate operator 262
Hand-held transmitter 259
Operation 262
Rolling code programming 261

433 Index
Removing
Ski sack 236
Vehicle battery 377
Wheel 372
Wiper blades 365
removing and installing
Front seat head restraints 109
Replacing
Bulbs 359
Front lamp bulbs 361
Front turn signal lamp bulb 362
Fuses 385
License plate lamp bulbs 363
Parking and standing lamp bulb 362
Rear lamp bulbs 360, 363
Side marker lamp bulb 363
Wiper blades 364
Reporting
Safety defects 18
Reprogramming
integrated remote control 263
Reset button in the instrument
cluster 138Resetting
All functions (control system) 138
All functions of a submenu 139
Fuel consumption 154
Service indicator (FSS) 298, 300,
301
Trip odometer 127
Residual heat utilization 182, 194
Residual ventilation 182, 194
REST (Residual engine heat
utilization) 194
Restraint system see Infant and child re-
straint systems 65
Rims and Tires 394
Roadside Assistance
Tele Aid* 250
Roadside assistance 12
Rolling code programming 261
RON (Research Octane Number) 279,
414
Roof rack* 233
Rotating wheels 293
Rubber parts
Cleaning 308S
Safety
Occupant 56
Safety belts see Seat belts 40
Safety defects
Reporting 18
Safety systems
Driving 74
Saving current speed 212
SBC 79
SBC brake system 415
Activation 80
Deactivation 81
Driving hints 81
Messages in display 326, 327
Self-check 81
Warning lamp 79
Sealing tires with TIREFIT 366
Seat belt force limiter 64
Seat belts 62
Cleaning 307
Fastening 40
Proper use of 42, 63
Safety guidelines 60
Warning lamp 315