memory MERCEDES-BENZ E500 2006 W211 Owner's Guide

260 Controls in detailDriving systems1Damping button
2Indicator lamps
Start the engine.

Press the damping button1 until the
desired suspension style is set.Vehicle level control
Your vehicle automatically adjusts its ride
height to


increase vehicle safety


reduce fuel consumption
The following vehicle chassis ride heights
can be selected:


Normal


Raised
The vehicle chassis ride height is raised or
lowered according to the selected level
setting and to the vehicle speed:


At a speed exceeding approximately
68 mph (110 km/h) with normal level
set or exceeding 75 mph (120 km/h)
with raised level set, the ride height is
reduced automatically. The table on
the next page provides an overview of
the vehicle levels.


With decreasing speed, the ride height
is again raised to the normal level.
!If you have selected the Comfort sus-
pension tuning, the vehicle lowers
slightly when you lock it within approx-
imately 60 seconds after switching off
the engine. When parking, make sure
that your vehicle cannot come into con-
tact with other objects, such as a curb,
while lowering. Your vehicle could oth-
erwise be damaged.iThe selected suspension style is stored
in memory, even after the SmartKey is
removed from the starter switch.

295 Controls in detail
Useful features
Step 2:
If you have previously programmed an
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when the indicator lamp1
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory.
If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and be-
gin directly with step 3.Step 3:

Hold the end of the hand-held remote
control5 of the device you wish to
train approximately 2 to 5 in
(5 to 12 cm) away from the signal
transmitter button (2, 3 or4) to be
programmed, while keeping the indica-
tor lamp1 in view.
Step 4:

Using both hands, simultaneously
press the hand-held remote control
button6 and the desired signal trans-
mitter button (2, 3 or4). Do not
release the buttons until step 5 is com-
pleted.
The indicator lamp1 will flash, first
slowly and then rapidly.Step 5:

After the indicator lamp1 changes
from a slow to a rapidly flashing light,
release the hand-held remote control
button and the signal transmitter but-
ton.
Step 6:

Press and hold the just-trained signal
transmitter button (2, 3 or4) and
observe the indicator lamp1.iThe indicator lamp1 flashes immedi-
ately the first time the signal transmit-
ter button is programmed. If this button
has already been programmed, the in-
dicator lamp will only start flashing af-
ter 20 seconds.


299 Controls in detail
Useful features
Erasing the integrated remote control
memory
Switch on the ignition (
page 36).

Simultaneously press and hold down
the outer signal transmitter buttons2
and 4, for approximately 20 seconds,
until the indicator lamp1 flashes rap-
idly. Do not hold for longer than
30 seconds.
The codes of all three channels are
erased.Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:


Check the frequency of the hand-held
remote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 288-399 MHz.


Put a new battery in the hand-held re-
mote control5. This will increase the
likelihood of the hand-held remote con-
trol sending a faster and more accurate
signal to the integrated remote control.


While performing step 3, hold the
hand-held remote control6 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming. Attempt varying an-
gles at the distance of 2 to 5 inches
(5 to 12 cm) away or the same angle at
varying distances.


If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.


Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.
iIf you sell your vehicle, erase the codes
of all three channels.
iCertain types of garage door openers
are incompatible with the integrated
remote control. If you should experi-
ence further difficulties with program-
ming the integrated remote control,
contact an authorized Mercedes-Benz
Center, or call Mercedes-Benz
Customer Assistance Center (in the
USA only) at 1-800-FOR-MERCedes, or
Customer Service (in Canada) at
1-800-387-0100.

386 Practical hintsWhat to do if …Vehicle status messages in the multi-function display
Warning and malfunction messages ap-
pear in the multifunction display located in
the instrument cluster.
Certain warning and malfunction messag-
es are accompanied by an audible signal.
Address these messages accordingly and
follow the additional instructions given in
this Operator’s Manual.
Selecting the vehicle status message
memory menu in the control system
(page 153) displays both cleared and
uncleared messages.
High-priority messages appear in the mul-
tifunction display in red color.Certain messages of high priority cannot
be cleared from the multifunction display
using the reset button (
page 150) or
buttonj, k, ÿ or è on the
multifunction steering wheel.
Other messages of high priority and mes-
sages of less immediate priority can be
cleared from the multifunction display us-
ing the reset button (
page 150) or
buttonj, k, ÿ or è on the
multifunction steering wheel. They are
then stored in the vehicle status message
memory (
page 162). Remember that
clearing a message will only make the mes-
sage disappear. Clearing a message will
not correct the condition that caused the
message to appear.
Warning!
G
All categories of messages contain impor-
tant information which should be taken note
of and, where a malfunction is indicated, ad-
dressed as soon as possible at an autho-
rized Mercedes-Benz Center.
Failure to repair condition noted may cause
damage not covered by the Mercedes-Benz
Limited Warranty, or result in property dam-
age or personal injury.Warning!
G
No messages will be displayed if either the
instrument cluster or the multifunction dis-
play is inoperative.
Contact the nearest authorized
Mercedes-Benz Center.

417 Practical hints
What to do if …
Display symbol
Display messages
Possible cause/consequence
Possible solution
<
Seat belt system
Drive to workshop
The seat belt system is malfunctioning.

Visit an authorized Mercedes-Benz
Center as soon as possible.
9
Service memory full
See Operator’s Manual
The maintenance service system memory
cannot save any more data.

Have the service memory checked by
an authorized Mercedes-Benz Center.
K
Close
tilt/sliding sunroof
You have opened the driver’s door with
the SmartKey removed from the starter
switch and the sliding portion of the
tilt/sliding sunroof* or tilt/sliding panel*
open.

Close the tilt/sliding sunroof*
(page 237) or tilt/sliding panel*
(page 241).
J
Close
tilt/sliding sunroof
You have opened the driver’s door with
the SmartKey removed from the starter
switch and the tilting portion of the
tilt/sliding sunroof* or tilt/sliding panel*
open.

Close the tilt/sliding sunroof*
(page 237) or tilt/sliding panel*
(page 241).

496 Technical termsMaintenance System (U.S. vehicles)
Maintenance service indicator in the
multifunction display that informs the
driver when the next vehicle mainte-
nance service is due. The
Maintenance System in your vehicle
tracks distance driven and the time
elapsed since your last maintenance
service, calculates other maintenance
service work required, and calls for the
next maintenance service accordingly.
Maximum loaded vehicle weight
(
page 354)
Maximum load rating
(page 354)
Maximum tire inflation pressure
(page 355)
Memory function*
Used to store three individual seat,
steering wheel and exterior mirror posi-
tions.MON
(M
otor O
ctane N
umber)
The Motor Octane Number for gasoline
as determined by a standardized meth-
od. It is an indication of a gasoline’s
ability to resist undesired detonation
(knocking). The average of both the
MON (Motor Octane Number) and
->RON (Research Octane Number) is
posted at the pump, also known as
ANTI-KNOCK INDEX.
Multifunction display
The display field in the instrument clus-
ter used to present information provid-
ed by the control system.
Multifunction steering wheel
Steering wheel with buttons for operat-
ing the control system.
Normal occupant weight
(
page 355)Overspeed range
Engine speeds within the red marking
on the tachometer dial. Avoid this en-
gine sp ee d ra nge , a s i t m ay re sul t in s e-
rious engine damage that is not
covered by the Mercedes-Benz Limited
Warranty.
Parktronic (Parking assist)*
System which uses visual and acoustic
signals to assist the driver during park-
ing maneuvers.
Poly-V-belt drive
Drives engine-components (alternator,
AC compressor, etc.) from the engine.

503 Index
Center console
Lower part 28
PASS AIR BAG OFF indicator
lamp 384
Upper part 27
Centigrate see Temperature display mode
Central locking
Automatic 129, 174
Locking/unlocking from inside 129
Central locking switch 129
Certification label 468
Checking
Oil level 320
Children in the vehicle 78
Air bags 68
Blocking of rear window operation 89
Indicator lamp, front passenger front
air bag
Infant and child restraint systems 78
LATCH-type child seat anchors 88
Occupant Classification System (OCS)
Cigarette lighter 282Climate control system
4-zone automatic climate
control 214
Air conditioning refrigerant 487
Air conditioning, Cooling 212, 227
Air distribution 208, 222
Air recirculation mode 210, 224
Air volume 209, 223
Automatic mode 206, 220
Control panel, Rear 213, 229
Deactivating system 206, 219
Dual-zone automatic climate
control 202
Front defroster 209, 223
Maximum cooling MAX COOL 224
Rear climate control 229
Residual engine heat (REST) 228
Clock 25, 168
Setting time 169
Cockpit 22, 493
Cockpit Management and Data System
see COMAND
Cold tire inflation pressure 354
Collapsible tire 480
Collapsible wheel chock 424
COMAND 494COMAND see separate COMAND operat-
ing instructions
Combination switch 55, 145
Control system 153, 494
Multifunction display 153
Multifunction steering wheel 154
Resetting to factory default 164
Control system menus 156, 157
AUDIO 159
Distronic* 161
NAV* 161
Settings 163
Standard display 159
TEL* 180
Trip computer 178
Vehicle status message memory 162
Control system submenus 155
Convenience 175
Instrument cluster 166
Lighting 170
Time/Date 168
Vehicle 174
Controller Area Network see CAN system
Convenience submenu
Setting parking position for exterior
rear view mirror 176

504 IndexCoolant
Anticorrosion/antifreeze mixing ratio
and quantity 491
Capacities 485
Checking coolant level 325
Messages in display 403, 404, 405
Temperature 314
Temperature indicator 151
Warning lamp 379
Cruise control 243, 494
Message in display 389
Cup holders 278
Cleaning 370
Curb weight 354
Customer Assistance Center see CAC
D
Date display, setting 169, 170
Daytime running lamp mode 142
Setting 170, 171
Deep water see Standing water
Defogging windshield 209, 224
Defrosting, Front 209, 223
Defrosting, Rear 201
Delayed shut-off
Exterior lamps 172
Interior lighting 173Department of Transportation see DOT
Diesel fuel 316
Diesel see Fuel
Difficulties
While driving 58
With starting 52
Digital clock see Clock
Digital speedometer 159
Dimensions, vehicle 482
Direction of rotation (tires) 331
Displays
Digital speedometer 159
Distronic* 249
Maintenance service indicator 360
Messages in display 398
Multifunction display 153
Outside temperature 153, 167
Symbol messages 398
Text messages 388
Vehicle status message memory 163
Vehicle system settings, Control
system 153
Distance to empty (Range), Trip
computer 178Distronic* 247, 494
Activating/deactivating 252
Cleaning system sensor 368
Control system 161
Distance warning function 256
Driving hints 257
Menu 251
Messages in display 389
Sensor cover 368
Warning and indicator lamps 250
Door
Entry lamps 148
Locking/unlocking, SmartKey 34,
108
Locking/unlocking, SmartKey with
KEYLESS-GO* 35, 114
Message in display 406
Opening from inside/outside 119
Remote door unlock (Tele Aid) 292
Unlocking, Mechanical key 426
Door control panel 32
Door handle 32
DOT 354, 494
Drinking and driving 303

510 Index
Fuel reserve 25, 378, 380
High beam headlamps 25
Instrument cluster 374, 375, 376,
377, 378, 379, 380, 381, 383
Low beam headlamps 25
Maintenance service indicator 360
Seat belt telltale 25
Seat belts 378, 380
SRS 67
Turn signals 25
Language, Setting 166
LATCH-type child seat anchors see Chil-
dren in the vehicle
License plate lamps 434
Messages in display 414
Replacing bulbs 438
Light alloy wheels, cleaning 370
Light sensor see Lamp sensor
Lighter see Cigarette lighter 282
Lighting
Daytime running lamp mode 142
Lighting, Exterior and interior 141
Limp Home Mode 196
Loading 268
Loading see Vehicle loading
Locator lighting 171Lock button
Door handle (KEYLESS-GO*) 64
Locking knob 495
Loss of Service and Warranty Information
Booklet 467
Loss of SmartKeys 110, 118
Low beam headlamps 54
Indicator lamp 25
Messages in display 414
Replacing bulbs 434
Switching on 54
Lubricants 484
Lumbar support 133
M
Maintenance 12
Calling up service indicator 362
Clearing service indicator
message 361
FSS (Canada vehicles) 360
Maintenance System (U.S.
vehicles) 360
Resetting service indicator 362
Service indicator 360
Service indicator message 360
Service term exceeded 361
Maintenance System (U.S. vehicles) 496Manual headlamp mode see Headlamps
Manual shift program E 55 AMG
Deactivating 195
Manual shift program E 55 AMG 193
Maximum load rating, Tires 354
Maximum loaded vehicle weight, Tire infla-
tion pressure 354
Maximum tire inflation pressure 355
Mechanical key 426
Memory function see Seats
Menus see Control system menus
Messages in display see Multifunction dis-
play messages
Minispare wheel see Spare wheel
Mirrors
Adjusting 45
Auto-dimming 197
Exterior rear view mirror 45
Exterior rear view mirror parking
positions 176, 198
Interior rear view mirror 45
MOExtended system* 343, 448
MOExtended tires* 479
MON 316
Motor Octane Number see MON

512 IndexOverspeed range, engine 496
Oxidation catalyst 312
P
Paintwork, Cleaning 365
Panic alarm 91
Panorama roof with power tilt/sliding
panel* 239
Messages in display 417
Opening/closing 240
Opening/closing in an
emergency 429
Stopping 241
Synchronizing 242
Panorama roof with tilt/sliding panel
Cleaning 370
Parcel net
Front passenger footwell 278
Parking 60, 306
On hills 60, 306
Over things that burn, Potential
consequences 60, 306
Parking brake 53, 61
Message in display 401
Parking lamps
Messages in display 413
Replacing bulbs 413Parking position
Exterior rear view mirrors 140, 176,
198
Gear position 50, 185
Parktronic* 496
Activating/deactivating 266
Cleaning system sensors 368
Malfunctioning 267
Minimum distance 265
Range 264
System sensors 368
Warning indicators 23, 265
Parts service 466
PASS AIR BAG OFF indicator lamp see
Front passenger front air bag off indica-
tor lamp
Passenger compartment
Interior lighting 147
Interior rear view mirror 45
Main fuse box 462
Parcel net in front passenger
footwell 278
Passenger safety see Occupant safety
Pedals 303
Phone see Telephone*
Plastic parts, cleaning 370Pliers, universal (vehicle tool kit) 424
Poly-V-belt drive 496
Layout 469
Positions (Memory function) see Seats
Power assistance 304
Power outlet 283
Power seat see Seats
Power tilt/sliding sunroof* 236
Messages in display 417
Opening/closing 236
Opening/closing in an
emergency 429
Stopping 238
Synchronizing 238
Power tilt/sliding sunroof* or panorama
roof with power tilt/sliding panel*
Emergency operations 429
Power train 497
Power washer 365
Power windows 231
Cleaning 369
Operating 231
Rear door window, Blocking
operation 89
Synchronizing 233
Practical hints 374