engine coolant MERCEDES-BENZ E550 4MATIC 2007 W211 Owner's Guide
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2007, Model line: E550 4MATIC, Model: MERCEDES-BENZ E550 4MATIC 2007 W211Pages: 522
Page 474 of 522
473 Technical data
Parts service
Warranty coverage
Identification labels
Layout of poly-V-belt drive
Engine
Rims and tires
Electrical system
Main dimensions and weights
Fuels, coolants, lubricants etc.
Page 492 of 522
491 Technical data
Fuels, coolants, lubricants etc.
Fuels, coolants, lubricants etc.
Capacities
Vehicle components and their respective
lubricants must match. Therefore only use
products tested and approved by
Mercedes-Benz.
Please refer to the Factory Approved
Service Products pamphlet (USA only), or
inquire at an authorized Mercedes-Benz
Center.
Warning!
G
Comply with all valid regulations with
respect to handling, storing and disposing of
service fluids. Otherwise you could
endanger persons or the environment.
Keep service fluids out of the reach of
children.
For health reasons, you should prevent
service fluids from coming into direct
contact with your skin or clothing.
If a service fluid is swallowed, contact a
physician immediately.
Model
Capacity
Fuels, coolants, lubricants etc.
Engine with oil filter
E 350
E 350 4MATIC
8.5 US qt (8.0 l)
Approved engine oils
E 320 BLUETEC
E 550
E 550 4MATIC
9.0 US qt (8.5 l)
Engine with oil filter
including oil cooler
E63AMG
9.3 US qt (8.8 l)
Approved engine oils
Page 495 of 522
494 Technical dataFuels, coolants, lubricants etc.
Model
Capacity
Fuels, coolants, lubricants etc.
Fuel tank
21.12 US gal (80.0 l)
Gasoline engine:
Premium unleaded gasoline
Minimum Posted Octane 91
(Avg. of 96 RON/86 MON)
Diesel engine:
ULTRA-LOW SULFUR DIESEL FUEL
(15 ppm SULFUR MAXIMUM)
including a reserve of
all except
E63AMG
2.38 US gal (9.0 l)
including a reserve of
E63AMG
3.7 US gal (14.0 l)
Air conditioning system
R-134a refrigerant and special PAG lubricant
oil (never R-12)
Windshield washer system
4.8 US qt (4.5 l)
MB Windshield Washer Concentrate
1
1Use MB Windshield Washer Concentrate “MB SummerFit” and water for temperatures above freezing or MB Windshield Washer Concentrate “MB SummerFit” and
commercially available premixed windshield washer solvent/antifreeze for temperatures below freezing point. Follow suggested mixing ratios (page 500).Windshield washer system and
headlamp cleaning system*
6.9 US qt (6.5 l)
MB Windshield Washer Concentrate
1
Page 496 of 522
495 Technical data
Fuels, coolants, lubricants etc.
Engine oils
Engine oils are specifically tested for their
suitability in our engines and durability for
our service intervals. Therefore, only use
approved engine oils and oil filters
required for vehicles with Maintenance
System (U.S. vehicles) or FSS PLUS
(Canada vehicles). For a listing of approved
engine oils and oil filters, refer to the
Factory Approved Service Products
pamphlet (USA only), or contact an
authorized Mercedes-Benz Center.
Engine oil additives
Do not blend oil additives with engine oil.
They may damage the engine.
Damage or malfunctions resulting from
blending oil additives are not covered by
the Mercedes-Benz Limited Warranty.Air conditioning refrigerant
R-134a (HFC) refrigerant and special PAG
lubricating oil are used in the air
conditioning system.
Never use R-12 (CFC) or mineral-based
lubricating oil. Otherwise damage to the
system will occur.
Brake fluid
Only brake fluid approved by
Mercedes-Benz is recommended. Your au-
thorized Mercedes-Benz Center will pro-
vide you with additional information.
!
Using engine oils and oil filters of specifica-
tion other than those expressly required for the
Maintenance System (U.S. vehicles) or
FSS PLUS (Canada vehicles), or changing of oil
and oil filter at change intervals longer than
those called for by the Maintenance System
(U.S. vehicles) or FSS PLUS (Canada vehicles)
will result in engine or emission control system
damage not covered by the Mercedes-Benz
Limited Warranty.Please follow Maintenance System (U.S. vehi-
cles) or FSS PLUS (Canada vehicles) recommen-
dations for scheduled oil changes. Failure to do
so will result in engine or emission control sys-
tem damage not covered by the Mercedes-Benz
Limited Warranty.
Warning!
G
During vehicle operation, the boiling point of
the brake fluid is continuously reduced
through the absorption of moisture from the
atmosphere. Under extremely strenuous
operating conditions, this moisture content
can lead to the formation of bubbles in the
system, thus reducing the system’s
efficiency.
Therefore, the brake fluid must be replaced
regularly. Refer to your vehicle’s
Maintenance Booklet for replacement
interval.
Page 497 of 522
496 Technical dataFuels, coolants, lubricants etc.Premium unleaded gasoline (gasoline engine)
Fuel requirements
Gasoline engine
Only use premium unleaded fuel:
The octane number (posted at the
pump) must be 91 min. It is an average
of both the Research Octane Number
(RON) and the Motor Octane Number
(MON): (RON+MON)/2. This is also
known as the ANTI-KNOCK INDEX.
Unleaded gasoline containing oxygenates
such as ethanol, IPA, IBA and TBA can be
used provided the ratio of any one of these
oxygenates to gasoline does not
exceed 10%; MTBE must not exceed 15%.
The ratio of methanol to gasoline must not
exceed 3% plus additional cosolvents.
Using mixtures of ethanol and methanol is
not allowed. Gasohol, which contains
10% ethanol and 90% unleaded gasoline,
can be used.
Warning!
G
Gasoline is highly flammable and poisonous.
It burns violently and can cause serious
personal injury.
Never allow sparks, flame or smoking mate-
rials near gasoline!
Turn off the engine before refueling.
Whenever you are around gasoline, avoid in-
haling fumes and skin or clothing contact,
extinguish all smoking materials.
Direct skin contact with fuels and the inha-
lation of fuel vapors can damage your
health.
!
To maintain the engine’s durability and per-
formance, premium unleaded gasoline must be
used. If premium unleaded gasoline is not avail-
able and low octane fuel is used, follow these
precautions:
Have the fuel tank only partially filled with
unleaded regular gasoline and fill up with
premium unleaded gasoline as soon as
possible.
Avoid full throttle driving and abrupt
acceleration.
Do not exceed an engine speed of 3 000 rpm
if the vehicle is loaded with a light load such
as two persons and no luggage.
Do not exceed
2/3 of maximum accelerator
pedal position if the vehicle is fully loaded or
operating in mountainous terrain.
Page 498 of 522
497 Technical data
Fuels, coolants, lubricants etc.
These blends must also meet all other fuel
requirements, such as resistance to spark
knock, boiling range, vapor pressure, etc.
Diesel engine
Only use commercially available vehicular
ULTRA-LOW SULFUR DIESEL FUEL
(15 ppm SULFUR MAXIMUM).
To prevent malfunctions, diesel fuel with
improved cold flow characteristics is of-
fered in the winter months. Check with
your fuel retailer.
Gasoline additives (gasoline engine)
A major concern among engine
manufacturers is carbon build-up caused
by gasoline. Mercedes-Benz recommends
only the use of quality gasoline containing
additives that prevent the build-up of
carbon deposits.
After an extended period of using fuels
without such additives, carbon deposits
can build up, especially on the intake
valves and in the combustion area, leading
to engine performance problems such as:
Warm-up hesitation
Unstable idle
Knocking/pinging
Misfire
Power lossIn areas where carbon deposits may be
encountered due to lack of availability of
gasolines which contain these additives,
Mercedes-Benz recommends the use of
additives approved by us for use on
Mercedes-Benz vehicles. Refer to Factory
Approved Service Products pamphlet
(USA only) or contact an authorized
Mercedes-Benz Center for a listing of
approved product(s). Follow directions on
product label.
Do not blend other fuel additives with fuel.
This only results in unnecessary cost and
may be harmful to the engine operation.
!
Do not fill the tank with gasoline. Do not
blend diesel fuel with gasoline or kerosene. The
fuel system and engine will otherwise be
damaged, which is not covered by the
Mercedes-Benz Limited Warranty.
!
Damage or malfunction resulting from poor
fuel quality or from blending additional fuel
additives other than those tested and approved
by us for use on Mercedes-Benz vehicles are not
covered by the Mercedes-Benz Limited
Warranty.
For a listing of approved products, refer to the
Factory Approved Service Products pamphlet
(USA only) or contact an authorized
Mercedes-Benz Center.
Page 499 of 522
498 Technical dataFuels, coolants, lubricants etc.Coolants
The engine coolant is a mixture of water
and anticorrosion/antifreeze, which pro-
vides:
Corrosion protection
Freeze protection
Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory
with a coolant providing freeze protection
to approximately -35°F (-37°C) and corro-
sion protection.
If the antifreeze mixture is effective to
-35°F (-37°C), the boiling point of the cool-
ant in the pressurized cooling system is
reached at approximately 266°F (130°C).The coolant solution must be used year
round to provide the necessary corrosion
protection and increase boil-over protec-
tion. Refer to Maintenance Booklet for re-
placement interval.
Coolant system design and coolant used
determine the replacement interval. The
replacement interval published in the
Maintenance Booklet is only applicable if
MB 325.0 Anticorrosion/Antifreeze solu-
tion or other Mercedes-Benz approved
products of equal specification are used to
renew the coolant concentration or bring it
back up to the proper level.
For information on other Mercedes-Benz
approved products of equal specification,
refer to the Factory Approved Service
Products pamphlet (USA only) or contact
an authorized Mercedes-Benz Center.
To provide important corrosion protection,
the solution must be at least 50% anticor-
rosion/antifreeze (equivalent to freeze
protection to approximately -35°F
[-37°C]). If you use a solution that is more than 55%
anticorrosion/antifreeze (freeze protec-
tion to approximately -49°F [-45°C]), the
engine temperature will increase due to
the lower heat transfer capability of the so-
lution. Therefore, do not use more than
this amount of anticorrosion/antifreeze.
If the coolant level is low, water and
MB 325.0 Anticorrosion/Antifreeze
should be used to bring it up to the proper
level (have cooling system checked for
signs of leakage). Please make sure the
mixture is in accordance with label instruc-
tions.
The water in the cooling system must meet
minimum requirements, which are usually
satisfied by normal drinking water. If you
are not sure about the water quality, con-
sult an authorized Mercedes-Benz Center.
!
Add premixed coolant solution only. Adding
water and MB 325.0 Anticorrosion/Antifreeze
separately from each other, could cause engine
damage not covered by the Mercedes-Benz
Limited Warranty.
Page 500 of 522
499 Technical data
Fuels, coolants, lubricants etc.
Anticorrosion/antifreeze
Your vehicle contains a number of
aluminum parts. The use of aluminum
components in motor vehicle engines
necessitates that anticorrosion/antifreeze
coolant used in such engines be
specifically formulated to protect the aluminum parts. Failure to use such
anticorrosion/antifreeze coolant will
result in a significantly shortened service
life.
Therefore, the following product is strongly
recommended for use in your vehicle:
MB 325.0 Anticorrosion/Antifreeze agent.Before the start of the winter season (or
once a year in hot southern regions), you
should have the anticorrosion/antifreeze
concentration checked. The coolant is also
regularly checked each time you bring your
vehicle to an authorized Mercedes-Benz
Center for service.
Anticorrosion/antifreeze quantityModel
Approx. freeze protection-35°F (-37°C)
-49°F (-45°C)
E 320 BLUETEC
6.9 US qt (6.5 l)
7.6 US qt (7.2 l)
E 350/E 350 4MATIC
5.3 US qt (5.0 l)
5.9 US qt (5.5 l)
E 550/E 550 4MATIC
6.0 US qt (5.7 l)
6.6 US qt (6.2 l)
E63AMG
6.2 US qt (5.9 l)
6.9 US qt (6.5 l)
Page 501 of 522
500 Technical dataFuels, coolants, lubricants etc.Windshield washer system and head-lamp cleaning system*
Both the windshield washer system and
headlamp cleaning system* are supplied
from the windshield washer reservoir.
The windshield washer reservoir has a ca-
pacity of approximately:
6.9 US qt (6.5 l) in vehicles with a
headlamp cleaning system*
4.8 US qt (4.5 l) in vehicles without a
headlamp cleaning system*
Refill the reservoir with MB Windshield
Washer Concentrate and water (or con-
centrate and commercially available
premixed windshield washer sol-
vent/antifreeze, depending on ambient
temperatures).Windshield and headlamp washer fluid
mixing ratio
For temperatures above freezing point, use
MB Windshield Washer Concentrate
“MB SummerFit” and water:
1 part “MB SummerFit” to 100 parts
water
(1.34 fl oz [40 ml] “MB SummerFit” to
1 gal [4.0 l] water).
For temperatures below freezing point use
MB Windshield Washer Concentrate
“MB SummerFit” and commercially avail-
able premixed windshield washer
solvent/antifreeze:
1 part “MB SummerFit” to 100 parts
solvent
(1.34 fl oz [40 ml] “MB SummerFit” to
1 gal [4.0 l] solvent).
Warning!
G
Washer solvent/antifreeze is highly flamma-
ble. Do not spill washer solvent/antifreeze
on hot engine parts, because it may ignite
and burn. You could be seriously burned.
Page 507 of 522
506 IndexEngine
Belt layout 478
Block heater* (Canada only) 365
Brake-in recommendations 308
Cleaning 371
Compartment 325
Malfunction indicator lamp 384, 385,
414
Maximum engine speed 479
Message in the display 384, 385,
414
Number 477
Starting 52
Starting with KEYLESS-GO* 53
Starting with the SmartKey 53
Tachometer 27
Technical data 479
Turning off with KEYLESS-GO* 64
Turning off with the SmartKey 63
Engine compartment
Hood 325
Engine coolant see Coolant
Engine malfunction indicator lamp 27,
385, 414Engine oil
Adding 329
Additives 495
Changing 329
Checking level 328
Consumption 327
Filler neck 329
Messages in display 418
Oil dipstick 328
Recommended engine oils and oil
filter 495
Engine oil level 324
ESP
®
100
Four wheel electronic traction system
with ESP
®
105
Messages in display 398, 413
Warning lamp 381, 382
ETD
Safety guidelines 72
Exterior lamp switch 137
Exterior rear view mirrors 47
Parking position 200
Exterior view 22F
Filler neck, Engine oil 329
First aid kit 432
Flat tire 452
Lowering the vehicle 458
Mounting the spare wheel 452, 455
Preparing the vehicle 452
Spare wheel 452
Flexible Service System see FSS
Floormats 290
Fluids
Automatic transmission fluid 492
Brake fluid 493
Capacities 491
Engine coolant 493
Engine oil 491
Power steering fluid 493
Windshield washer and headlamp
cleaning system 494
Fog lamps 140
Messages in display 422, 423, 424,
425
Replacing bulbs 445
Four wheel electronic traction system with
ESP
® see 4MATIC
4MATIC 105