buttons MERCEDES-BENZ E63AMG 2007 W211 Owner's Guide

304 Controls in detailUseful featuresStep 9:
Press the “training” button on the ga-
rage door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the follow-
ing two steps.
Step 10:

Return to the vehicle and firmly press,
hold for 2 seconds and release the pro-
grammed signal transmitter button
(2, 3 or4).
Step 11:

Press, hold for 2 seconds and release
same signal transmitter button a sec-
ond time to complete the training pro-
cess.Step 12:

Confirm the garage door operation by
pressing the programmed signal trans-
mitter button (2, 3 or4).
Step 13:

To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the
integrated signal transmitter to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:Step 4:

Press and hold the signal transmitter
button (2, 3 or4). Do not release
this button until it has been successful-
ly trained.

While still holding down the signal
transmitter button (2, 3 or4),
“cycle” your hand-held remote control
button6 as follows: Press and hold
button6 for 2 seconds, then release
it for 2 seconds, and again press and
hold it for 2 seconds. Repeat this se-
quence on the hand-held remote con-
trol until the frequency signal has been
learned. Upon successful training, indi-
cator lamp1 will flash slowly and then
rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete.
i
Some garage door openers (or other rolling
code equipped devices) may require you to
press, hold for 2 seconds and release the same
signal transmitter button a third time to com-
plete the training process.


305 Controls in detail
Useful features
Reprogramming a single signal trans-
mitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:
Switch on the ignition (
page 37).

Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.

Indicator lamp1 will begin to flash af-
ter 20 seconds. Without releasing the
signal transmitter button, proceed with
programming starting with step 3.Operation of integrated remote control

Switch on the ignition (
page 37).

Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing the integrated remote control
memory

Switch on the ignition (
page 37).

Simultaneously press and hold outer
signal transmitter buttons2 and 4,
for approximately 20 seconds, until
indicator lamp1 flashes rapidly. Do
not hold for longer than 30 seconds.
The codes of all three channels are
erased.Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:


Check the frequency of hand-held re-
mote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 280-390 MHz.


Put a new battery in hand-held remote
control5. This will increase the likeli-
hood of the hand-held remote control
sending a faster and more accurate sig-
nal to the integrated remote control.


While performing step 3, hold
hand-held remote control5 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming. Attempt varying an-
gles at the distance of 2 to 5 inches
(5 to 12 cm) away or the same angle at
varying distances.
i
Upon completion of programming the inte-
grated remote control, make sure you retain the
hand-held remote control that came with the ga-
rage door opener, gate operator or other device.
You may need it for use in other vehicles, for fu-
ture programming of an integrated remote con-
trol, or simply for continued use as a hand-held
remote control to operate the respective device
in other situations.
i
If you sell your vehicle, erase the codes of all
three channels.

515 Index
Shifting, Automatic transmission 184
Side impact air bags 75
Side marker lamps
Cleaning lenses 372
Side windows see Power windows
Sidewall 361
Ski bag* (Canada only) 274
SmartKey see Key, SmartKey 110
SmartKey with KEYLESS-GO* see Key,
SmartKey with KEYLESS-GO* 113
Snow chains 365
Snow tires 364
Spare fuses 469
Spare wheel 432
Mounting 452
Speed settings
Cruise control 251
Distronic* 259
Speedometer 27, 255
SRS 68
Indicator lamp 27, 390
Message in display 429
Standing water, Driving through 317
Starter switch 37
Positions 37
Starting difficulties, Engine 54Starting, Engine 52
Steering column 45
Steering wheel 45
Buttons 28
Steering wheel gearshift control one-touch
gearshifting*
Automatic transmission 192
Steering wheel, Cleaning 376
Stolen Vehicle Recovery services 301
Storage compartments 32
Cup holder 285
Glove box 282
Parcel net in front passenger
footwell 282
Rear armrest 283
Rear center console 282
Ruffled storage bags 283
Storing
Tires 335
Submenus
In control system
Submenus see Control system menus and
submenus
Sun visors 201
Sunroof see Power tilt/sliding sunroof
Sunshade* 202Suspension tuning
For comfortable driving style 265
For sporty driving style 265
Suspension tuning see Airmatic DC (Dual
Control)
Symbols used in this operator’s
manual 15
T
Tachometer 27, 149
Overspeed range 149
Tail lamps 448
Cleaning lenses 372
Messages in display 425
Replacing bulbs 448
Taillamps
Messages in display 425
Tar stains 370