fuse MERCEDES-BENZ E63AMG 2007 W211 Owner's Manual

ContentsReplacing bulbs ................................. 443
Bulbs ............................................ 443
Replacing bulbs for front lamps.... 446
Replacing bulbs for rear lamps ..... 448
Replacing wiper blades ...................... 450
Placing wiper arms in vertical
position ........................................ 450
Removing wiper blades ................ 451
Installing wiper blades.................. 451
Flat tire .............................................. 452
Preparing the vehicle.................... 452
Mounting the spare wheel ............ 452
Bleeding the fuel system
(diesel engine only) ............................ 459
Battery ............................................... 460
Disconnecting the battery ............ 461
Removing the battery ................... 462
Charging and reinstalling the
battery.......................................... 462
Reconnecting the battery ............. 463
Jump starting ..................................... 464
Towing the vehicle ............................. 466
Installing towing eye bolt.............. 468Fuses ................................................. 469
Fuse box in passenger
compartment ............................... 470
Fuse box in trunk ......................... 470
Technical data................................. 473
Parts service ...................................... 474
Warranty coverage............................. 475
Loss of Service and Warranty
Information Booklet ..................... 475
Identification labels ........................... 476
Layout of poly-V-belt drive ................. 478
E 320 BLUETEC ............................ 478
E 350 / E 550 ............................... 478
E 63 AMG ..................................... 478
Engine................................................ 479
Rims and tires.................................... 481
Same size tires ............................. 482
Mixed size tires ............................ 485
Spare wheel ................................. 487
Electrical system ............................... 488
Main dimensions and weights............ 489
Main dimensions .......................... 489
Weights ........................................ 490Fuels, coolants, lubricants etc. .......... 491
Capacities .................................... 491
Engine oils ................................... 495
Engine oil additives ...................... 495
Air conditioning refrigerant .......... 495
Brake fluid.................................... 495
Premium unleaded gasoline
(gasoline engine).......................... 496
Fuel requirements ........................ 496
Gasoline additives
(gasoline engine).......................... 497
Coolants ...................................... 498
Windshield washer system and
headlamp cleaning system*......... 500
Index................................................. 501

244 Controls in detailPower tilt/sliding sunroofStopping the power tilt/sliding sunroof
during Express-operation
Move the sunroof switch in any direc-
tion.Synchronizing the power tilt/sliding
sunroof
The tilt/sliding sunroof must be synchro-
nized

after the battery has been
disconnected or discharged


after the tilt/sliding sunroof has been
closed manually (
page 439)


after a malfunction


if the tilt/sliding sunroof does not open
smoothly

Remove the respective fuse from the
main fuse box (
page 470).

Reinsert the fuse in the main fuse box.

Switch on the ignition (
page 37).

Move and hold the sunroof switch in di-
rection of arrow3 until the tilt/sliding
sunroof is fully raised at the rear.
Keep holding the sunroof switch in di-
rection of arrow3 for approximately
1 second.

Check the Express-open feature
(page 243).
If the tilt/sliding sunroof opens com-
pletely, the roof is synchronized. Other-
wise repeat the above steps.
i
If the movement of the tilt/sliding sunroof is
blocked during the Express-close procedure, the
tilt/sliding sunroof will stop and reopen slightly.

248 Controls in detailPanorama roof with power tilt/sliding panel*Opening and closing the panorama roof
with power tilt/sliding panel
To open, close, raise, or lower the
tilt/sliding panel, move the roof panel
switch to resistance point in the re-
quired direction of arrows1 to4.
Release the roof panel switch when the
tilt/sliding panel has reached the de-
sired position.
Fully opening (Express-open) the pan-
orama roof with power tilt/sliding pan-
el

Move the roof panel switch past the re-
sistance point in direction of arrow1
and release.
The tilt/sliding panel opens
completely.
Stopping the panorama roof with power
tilt/sliding panel during Express-open

Move the roof panel switch in any di-
rection.Synchronizing the panorama roof with
power tilt/sliding panel
The tilt/sliding panel must be
synchronized

after the battery has been
disconnected or discharged


after the tilt/sliding panel has been
closed manually (
page 439)


after a malfunction


if the tilt/sliding panel does not open
smoothly

Remove the fuse from the main fuse
box (
page 469).

Reinsert the fuse in the main fuse box.

Switch on the ignition (
page 37).

Move and hold the roof panel switch in
direction of arrow2 until the roller
sunblinds are fully closed.

Keep holding the roof panel switch in
direction of arrow2 for approximately
1 second.

Move and hold the roof panel switch in
direction of arrow1 until the roller
sunblinds are fully opened.

Keep holding the roof panel switch in
direction of arrow1 for approximately
1 second.

Move and hold the roof panel switch in
direction of arrow3 until the tilt/slid-
ing panel is fully raised.

Keep holding the roof panel switch in
direction of arrow3 for approximately
1 second.

Move and hold the roof panel switch in
direction of arrow2 until the tilt/slid-
ing panel is fully closed.

Keep holding the roof panel switch in
direction of arrow2 for approximately
1 second.

Check the Express-open feature of the
tilt/sliding panel (
page 248).
If the tilt/sliding panel opens com-
pletely, the roof is synchronized. Other-
wise repeat the above steps.

368 OperationMaintenanceCalling up the maintenance service indicator display
You can call up the maintenance service
indicator display at any time to check
when the next maintenance service is due.
Switch on the ignition (
page 37).

Press button è or ÿ on the mul-
tifunction steering wheel repeatedly
until the standard display appears in
the multifunction display (
page 151).

Press button k or j until the
maintenance service indicator display
with the service symbol 9 and the
service deadline appears in the multi-
function display.Resetting the maintenance service
indicator
In the event that the maintenance service
on your vehicle is not carried out by an au-
thorized Mercedes-Benz Center, you can
have the maintenance service indicator re-
set. The automotive maintenance facility
carrying out the maintenance service will
find the information for resetting the main-
tenance service indicator in the mainte-
nance-relevant information for your
vehicle. Such information is available from
either your authorized Mercedes-Benz
Center or directly from Mercedes-Benz.
i
If the battery is disconnected, the days of
disconnection will not be included in the count
shown by the maintenance service indicator. To
arrive at the true maintenance service deadline,
you will need to subtract these days from the
days shown in the maintenance service indicator
message or maintenance service indicator dis-
play.
Do not confuse the maintenance service indica-
tor with the engine oil level indicator :.
i
If the maintenance service indicator was in-
advertently reset, have an authorized
Mercedes-Benz Center correct it.
Only reset if the proper maintenance service has
been performed. Resetting the system without
performing the proper service as called for by
the maintenance service indicator will result in
engine damage and/or other vehicle damage not
covered by the Mercedes-Benz Limited
Warranty.

371 Operation
Vehicle care
Engine cleaning
Prior to cleaning the engine compartment,
make sure to protect electrical compo-
nents and connectors from contact with
water and cleaning agents.
Corrosion protection, such as MB Anticor-
rosion Wax should be applied to the engine
compartment after every engine cleaning.
Before applying, all control linkage bush-
ings and joints should be lubricated. The
poly-V-belt and all pulleys should be pro-
tected from any wax.
Vehicle washing
In the winter, thoroughly remove all traces
of road salt as soon as possible.
When washing the vehicle underbody, do
not forget to clean the inner sides of the
wheels.Hand-wash
Do not use hot water or wash your vehicle
in direct sunlight.

Only use a mild car wash detergent,
such as Mercedes-Benz approved Car
Shampoo.

Thoroughly spray the vehicle with a dif-
fused jet of water.
Direct only a very weak spray towards
the ventilation intake.

Use plenty of water and rinse the
sponge and chamois frequently.

Rinse with clean water and thoroughly
dry with a chamois.
Do not allow cleaning agents to dry on
the finish.Automatic car wash
You can have your car washed in an auto-
matic car wash from the start. Automatic
car washes without brushes are prefera-
ble.

To protect the filter system, switch the
automatic climate control to air recir-
culation mode (
page 214) or
(
page 231).
If the vehicle is very dirty, prewash it be-
fore running it through the automatic car
wash.
i
Vehicles with KEYLESS-GO*:
If a door handle is hit by a strong jet of water, and
a SmartKey with KEYLESS-GO* is in close prox-
imity, i.e. within approximately 3 ft (approxi-
mately 1 m), the vehicle could be inadvertently
locked or unlocked.
!
Do not use scouring agents on these parts.
Never apply strong force and only use a soft,
non-scratching cloth when cleaning the vehicle.
Do not attempt to wipe the surface with a dry
cloth or sponge.
Otherwise you may scratch or damage the paint.
!
Do not clean your vehicle in an automatic
touchless car wash which uses caustic spray.
Otherwise the caustic spray will damage the
paint or ornamental moldings.

379 Practical hints
What to do if …
Where will I find ...?
Unlocking/locking in an emergency
Opening/closing in an emergency
Resetting activated head restraints
Replacing SmartKey batteries
Replacing bulbs
Replacing wiper blades
Flat tire
Bleeding the fuel system
(diesel engine only)
Battery
Jump starting
Towing the vehicle
Fuses

434 Practical hintsWhere will I find ...?Vehicle tool kit
The vehicle tool kit is stored in the com-
partment underneath the trunk floor
(page 432).
The vehicle tool kit includes:


One pair of universal pliers


One towing eye bolt


One wheel wrench


One alignment bolt


One fuse extractor


Spare fuses


Collapsible wheel chock


A pair of gloves
Setting up the collapsible wheel chock
The collapsible wheel chock serves to
additionally secure the vehicle, e.g. while
changing the wheel.1Tilt the plates upward
2Fold the lower plate outward
3Insert the plate

Tilt both plates upward1.

Fold the lower plate outward2.

Guide the tabs of the lower plate all the
way into the openings of the base
plate3.
Vehicle jackWarning!
G
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into both sides of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always
firmly set parking brake and block wheels
before raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use,
especially on hills. Always try to use the jack
on level surface. Make sure the jack arm is
fully seated in the jack take-up bracket.
Always lower the vehicle onto sufficient
capacity jackstands before working under
the vehicle.

469 Practical hintsFuses
Fuses
The electrical fuses in your vehicle serve to
switch off malfunctioning power circuits.
If a fuse is blown, the components and sys-
tems secured by that fuse will stop operat-
ing.If a newly inserted fuse blows again, have
the cause determined and rectified by an
authorized Mercedes-Benz Center.
The following aids are available to help you
replace fuses.


Fuse chart
The fuse chart is located in the fuse box
in the passenger compartment
(page 470). The fuse chart explains
the fuse allocation and fuse amperag-
es.


Spare fuses
Spare fuses are located in the vehicle
tool kit in the trunk (
page 434).


Fuse extractor
The fuse extractor is located in the ve-
hicle tool kit in the trunk (
page 434).The electrical fuses are located in different
fuse boxes:


in the passenger compartment on the
driver’s side (
page 470)


in the trunk (
page 470)
Before replacing fuses:

Apply the parking brake (
page 62).

Make sure the gear selector lever is set
to position P (
page 184).

Turn off all electrical consumers.

Turn off the engine (
page 63).

Remove the SmartKey from the starter
switch.
Vehicles with KEYLESS-GO*:
Open the driver’s door.
Warning!
G
Only use fuses approved by Mercedes-Benz
with the specified amperage for the system
in question and do not attempt to repair or
bridge a blown fuse. Using other than ap-
proved fuses or using repaired or bridged
fuses may cause an overload leading to a
fire, and/or cause damage to electrical
components and/or systems. Have the
cause determined and remedied by an
authorized Mercedes-Benz Center.i
A blown fuse must be replaced by an appro-
priate spare fuse (recognizable by its color or the
fuse rating given on the fuse) of the amperage
recommended in the fuse chart.
Any Mercedes-Benz Center will be glad to advise
you on this subject.

470 Practical hintsFusesFuse box in passenger compartment
The fuse box is located behind a cover in
the dashboard on the driver’s side.
1Cover
2Recess in the coverOpening

Open the driver’s door.

Insert flat, blunt object as a lever in
recess2 on the edge of cover1.

Loosen cover1 from the dashboard
using lever.

Using your hands, pull cover1 in di-
rection of arrow and remove.
Closing

Hook cover1 into the opening at the
front.

Press cover1 back on until it engag-
es.
Fuse box in trunk
The fuse box is located behind the
left-hand trim panel in the trunk.
Fuse box cover design may vary depending
on vehicle equipment. Cover with turn catches shown1Catches
2Cover
Opening cover (with turn catches)
Turn catches1 counter-clockwise.
and remove cover2.
!
Do not use sharp objects such as a screw
driver to open the fuse box cover1 in the dash-
board, as this could damage it.
!
The cover1 must be properly positioned
as described to prevent moisture or dirt from en-
tering the fuse box and possibly impairing fuse
operation.

471 Practical hintsFuses
Closing cover (with turn catches)
Install cover2 (
page 470).

Turn catches1 (
page 470) clock-
wise.
Opening cover (without turn catches)

Hold cover at recess, press cover
slightly together to release tabs from
behind trim panel and then pull off cov-
er.Closing cover (without turn catches)

Install cover with tabs on one side of
trim panel, then press cover slightly to-
gether to install cover on other side of
trim panel.