remote control MERCEDES-BENZ E63AMG WAGON 2007 S211 User Guide

299 Controls in detail
Useful features
Remote door unlock
In case you have locked your vehicle unin-
tentionally (e.g. SmartKey inside vehicle),
and the reserve SmartKey is not handy:
Contact the Mercedes-Benz Response
Center at 1-800-756-9018 (in the USA)
or 1-888-923-8367 (in Canada).
You will be asked to provide your pass-
word which you provided when you
completed the subscriber agreement.

Then return to your vehicle and pull the
tailgate recessed handle for a minimum
of 20 seconds until the SOS button is
flashing.
The message
Call connected
appears
in the multifunction display.
As an alternative, you may unlock the vehi-
cle via Internet using the ID and password
sent to you shortly after the completion of
your acquaintance call.
The Response Center will then unlock your
vehicle with the remote door unlocking
feature.Stolen Vehicle Recovery services
In the event your vehicle was stolen:

Report the incident to the police.
The police will issue a numbered inci-
dent report.

Pass this number on to the
Mercedes-Benz Response Center along
with your password issued to you when
you subscribed to the service.
The Response Center will then attempt
to covertly contact the vehicle’s
Tele Aid system. Once the vehicle is lo-
cated, the Response Center will con-
tact the local law enforcement and you.
The vehicle’s location will only be pro-
vided to law enforcement.
i
The remote door unlock feature is available
if the relevant cellular phone network is avail-
able.
The SOS button will flash and the message
Call connected
will appear in the multifunc-
tion display to indicate receipt of the door unlock
command.
Once the vehicle is unlocked, a Response Center
specialist will attempt to establish voice contact
with the vehicle occupants.
If the tailgate recessed handle was pulled for
more than 20 seconds before door unlock autho-
rization was received by the Response Center,
you must wait 15 minutes before pulling the tail-
gate recessed handle again.
i
When the anti-theft alarm stays on for more
than 30 seconds, a call is initiated automatically
to the Response Center. See anti-theft alarm
system (
page 106).

300 Controls in detailUseful featuresGarage door opener
The integrated remote control is capable of
operating up to three separately controlled
devices. It provides a convenient way to re-
place up to three hand-held remote con-
trols used to operate devices such as
garage door openers, gate openers, or oth-
er devices compatible with HomeLink
® or
some other systems.
Before the integrated remote control can
be used, it must be programmed to the ga-
rage door opener, gate operator or other
device you wish to operate. See the follow-
ing instructions for programming informa-
tion.
Interior rear view mirror with integrated re-
mote control1Indicator lamp
2 3 4Signal transmitter button
Needed for programming (not part of vehi-
cle equipment):
5Hand-held remote control of ga-
rage door opener, gate operator
or other device
6Hand-held remote control but-
ton
Warning!
G
Before programming the integrated remote
control to a garage door opener or gate
operator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage. When programming
a garage door opener, the door moves up or
down. When programming a gate operator,
the gate opens or closes.
Do not use the integrated remote control
with any garage door opener that lacks
safety stop and reverse features as required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982).
A garage door that cannot detect an object
- signaling the door to stop and reverse -
does not meet current U.S. federal safety
standards.

301 Controls in detail
Useful features
Programming the integrated remote
control
Step 1:
Switch on the ignition (
page 37).Step 2:

If you have previously programmed a
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when the indicator lamp1
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory.
If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and be-
gin directly with step 3.Step 3:

Hold the end of hand-held remote
control5 of the device you wish to
train approximately 2 to 5 in
(5 to12 cm) away from the signal trans-
mitter button (2, 3 or4) to be pro-
grammed, while keeping the indicator
lamp1 in view.
Step 4:

Using both hands, simultaneously
press hand-held remote control
button6 and the desired signal trans-
mitter button (2, 3 or4). Do not
release the buttons until step 5 is com-
pleted.
Indicator lamp1 will flash, first slowly
and then rapidly.
When programming a garage door opener,
park vehicle outside the garage.
Do not run the engine while programming
the integrated remote control. Inhalation of
exhaust gas is hazardous to your health. All
exhaust gas contains carbon
monoxide (CO), and inhaling it can cause
unconsciousness and possible death.
i
The indicator lamp
1
flashes immediately
the first time the signal transmitter button is pro-
grammed. If this button has already been pro-
grammed, the indicator lamp will only start
flashing after 20 seconds.


302 Controls in detailUseful featuresStep 5:
After indicator lamp1 changes from a
slow to a rapidly flashing light, release
the hand-held remote control button
and the signal transmitter button.
Step 6:

Press and hold the just-trained signal
transmitter button (2, 3 or4) and
observe the indicator lamp1.
If indicator lamp1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button (2, 3 or4) is pressed and re-
leased.
Step 7:

To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.Rolling code programming
To train a garage door opener (or other
rolling code devices) with the rolling code
feature, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
Step 8:

Locate “training” button on the garage
door opener motor head unit.
Exact location and color of the button
may vary by garage door opener brand.
Depending on manufacturer, the
“training” button may also be referred
to as “learn”or “smart” button. If there
is difficulty locating the transmitting
button, refer to the garage door opener
Operator’s Manual. Step 9:

Press the “training” button on the ga-
rage door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the follow-
ing two steps.
Step 10:

Return to the vehicle and firmly press,
hold for 2 seconds and release the pro-
grammed signal transmitter button
(2, 3 or4).
Step 11:

Press, hold for 2 seconds and release
same signal transmitter button a sec-
ond time to complete the training pro-
cess.
i
If indicator lamp1 flashes rapidly for about
2 seconds and then turns to a constant light,
continue with programming steps 8 through 12
as your garage door opener may be equipped
with the “rolling code” feature.
i
Some garage door openers (or other rolling
code equipped devices) may require you to
press, hold for 2 seconds and release the same
signal transmitter button a third time to com-
plete the training process.


303 Controls in detail
Useful features
Step 12:
Confirm the garage door operation by
pressing the programmed signal trans-
mitter button (2, 3 or4).
Step 13:

To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the
integrated signal transmitter to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:Step 4:

Press and hold the signal transmitter
button (2, 3 or4). Do not release
this button until it has been successful-
ly trained.

While still holding down the signal
transmitter button (2, 3 or4),
“cycle” your hand-held remote control
button6 as follows: Press and hold
button6 for 2 seconds, then release
it for 2 seconds, and again press and
hold it for 2 seconds. Repeat this se-
quence on the hand-held remote con-
trol until the frequency signal has been
learned. Upon successful training, indi-
cator lamp1 will flash slowly and then
rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete.Reprogramming a single signal trans-
mitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:

Switch on the ignition (
page 37).

Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.

Indicator lamp1 will begin to flash af-
ter 20 seconds. Without releasing the
signal transmitter button, proceed with
programming starting with step 3.
i
Upon completion of programming the inte-
grated remote control, make sure you retain the
hand-held remote control that came with the ga-
rage door opener, gate operator or other device.
You may need it for use in other vehicles, for fu-
ture programming of an integrated remote con-
trol, or simply for continued use as a hand-held
remote control to operate the respective device
in other situations.

304 Controls in detailUseful featuresOperation of integrated remote control
Switch on the ignition (
page 37).

Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing the integrated remote control
memory

Switch on the ignition (
page 37).

Simultaneously press and hold outer
signal transmitter buttons2 and 4,
for approximately 20 seconds, until
indicator lamp1 flashes rapidly. Do
not hold for longer than 30 seconds.
The codes of all three channels are
erased.Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:


Check the frequency of hand-held re-
mote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 280-390 MHz.


Put a new battery in hand-held remote
control5. This will increase the likeli-
hood of the hand-held remote control
sending a faster and more accurate sig-
nal to the integrated remote control.


While performing step 3, hold
hand-held remote control5 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming. Attempt varying an-
gles at the distance of 2 to 5 inches
(5 to 12 cm) away or the same angle at
varying distances.


If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.


Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.
i
If you sell your vehicle, erase the codes of all
three channels.
i
Certain types of garage door openers are in-
compatible with the integrated remote control. If
you should experience further difficulties with
programming the integrated remote control,
contact an authorized Mercedes-Benz Center, or
call Mercedes-Benz Customer Assistance Cen-
ter (in the USA only) at 1-800-FOR-MERCedes, or
Customer Service (in Canada) at
1-800-387-0100.

321 Operation
At the gas station
At the gas station
Refueling
The fuel filler flap is located on the
right-hand side of the vehicle towards the
rear. Locking/unlocking the vehicle with
the remote control automatically
locks/unlocks the fuel filler flap.

Turn the engine off

by turning the SmartKey to
position0.


by pressing the KEYLESS-GO*
start/stop button. Open the driv-
er’s door (with the driver’s door
open, starter switch is now in
position0, same as SmartKey re-
moved from starter switch).

Remove the SmartKey from the starter
switch.

Open the fuel filler flap by pushing at
the point indicated by the arrow.
The fuel filler flap springs open.

Turn the fuel cap to the left and hold on
to it until possible pressure is released.

Take off the cap and set it in the recess
on the fuel filler flap.
To prevent fuel vapors from escaping
into open air, fully insert filler nozzle
unit.

Only fill your tank until the filler nozzle
unit cuts out – do not top off or over-
fill.
Warning!
G
Gasoline is highly flammable and poisonous.
It burns violently and can cause serious
injury.
Never allow sparks, flame or smoking mate-
rials near gasoline!
Turn off the engine before refueling.
Whenever you are around gasoline, avoid in-
haling fumes and skin or clothing contact,
extinguish all smoking materials.
Direct skin contact with fuels and the inha-
lation of fuel vapors can damage your
health.
i
In case that the central locking system does
not release the fuel filler flap, or the opening
mechanism is clamping, notify Roadside Assis-
tance or an authorized Mercedes-Benz Center.
Warning!
G
Overfilling of the fuel tank may create pres-
sure in the system which could cause a gas
discharge. This could cause the gas to spray
back out when removing the fuel pump noz-
zle, which could cause personal injury.


499 Index
Distronic* 249
Activating/deactivating 255
Cleaning system sensor 372
Control system 167
Distance warning function 258
Driving hints 259
Menu 253
Messages in display 397
Sensor cover 372
Warning and indicator lamps 252
Door
Entry lamps 151
Locking/unlocking, SmartKey 36,
112
Locking/unlocking, SmartKey with
KEYLESS-GO* 37, 117
Message in display 428
Opening from inside/outside 120
Remote door unlock (Tele Aid) 299
Unlocking, Mechanical key 435
Door control panel 34
Door handle 34
DOT 359
Drinking and driving 309Driving
Abroad 317
Hydroplaning 314
In winter 316
Instructions 49, 309
Problems 60
Safety systems 97
Through standing water 317
With Distronic* 259
Driving safety systems
4MATIC 104
ABS 97
BAS 99
EBP 100
ESP
®
100
Driving systems
Airmatic DC (Dual Control) 261
Cruise control 246
Distronic* 249
Driving tips 191
Accelerator position 191
Kickdown 191E
Easy-entry/exit feature 46, 181
EBP 100
Electrical fuses see Fuses
Electrical system, Technical data 484
Electronic Stability Program see
ESP
®
100
Emergency calls
Tele Aid calls 294
Emergency operation (Limp-Home
Mode) 199
Emergency operations
Gear selector lever, Unlocking 437
Locking/unlocking the vehicle 435
Remote door unlock 299
Tilt/sliding sunroof, Manual
operation 438
Emergency Tensioning Device see ETD

503 Index
Inflation pressure see Tires, Inflation pres-
sure
Inside door handle 120
Instrument cluster 26, 152
Illumination brightness 152
Lamps 378
Multifunction display 155
Instrument lighting see Instrument cluster,
Illumination brightness
Instrument panel see Instrument cluster
Instruments and controls see Cockpit
Interior lighting
Delayed shut-off 179
Interior rear view mirror 47
Auto-dimming mirrors 200
Interior storage spaces see Storage com-
partments
J
Jack 433
Jump starting 466
K
Key, Mechanical 435
Loss of 119Key, SmartKey
Battery check lamp 110
Checking batteries 119
Factory setting 112
Global locking 112, 113
Global unlocking 112, 113
Locking/unlocking 36, 65, 110
Loss of 119
Messages in the multifunction
display 418, 419
Opening and closing the power
tilt/sliding sunroof 241
Opening and closing the
windows 241
Opening, Tailgate 121
Positions in starter switch 37
Remote control 110
Replacing batteries 440
Restoring to factory setting 113
Selective setting 112
Starting the engine 52
Turning off the engine 63Key, SmartKey with KEYLESS-GO*
Battery check lamp 114
Checking batteries 119
Factory setting 116
Global locking 117, 118
Global unlocking 117, 118
Locking/unlocking 37, 65, 113
Loss of 119
Messages in the multifunction
display 418, 419
Opening and closing the power
tilt/sliding sunroof 241
Opening and closing the
windows 241
Opening, Tailgate 121
Replacing batteries 440
Restoring to factory setting 118
Selective setting 117
Starting the engine 53
Turning off the engine 64
KEYLESS-GO* see Key, SmartKey with
KEYLESS-GO*
Kickdown 191
Kilopascal 359

507 Index
PRE-SAFE
®
Messages in display 396, 405
Problems
While driving 60
With vehicle 17
Product information 9
Production options weight 359
Program mode see Automatic transmis-
sion, Automatic shift program
Program mode selector switch
Automatic shift program 193
PSI 360
Push-start see Tow-start
R
Radio
Selecting stations 165
Selecting stations (satellite*) 165
Radio transmitters 318
Reading lamp, front 150
Reading lamp, rear 151
Rear bench seat, foldable 266
Rear door ashtray see Ashtray
Rear door window
Blocking operation 95
Rear fog lamp see Fog lamps 145
Rear lamps see Tail lampsRear seat head restraints see Head re-
straints
Rear view mirrors see Mirrors
Rear window defroster 204
Rear window wiper/washer 59
Recommended inflation pressure 360
Recovery services, Stolen vehicle
(Tele Aid) 299
Refrigerant, Air conditioning 489
Refueling 321
Regular checks 322
Reminder, Seat belt see Seat belts,
Telltale 386
Remote control see Key, SmartKey
Remote door unlock (Tele Aid) 299
Replacing bulbs
Additional turn signals 446
Brake lamps 444
Headlamps 444
High beam headlamps 443
High mounted brake lamp 443
License plate lamps 443, 447
Low beam headlamps 442, 444
Parking lamps 443, 446
Side marker lamps 442
Side marker lamps, front 446Tail lamps 443, 447
Turn signal lamps 442, 446
Reporting safety defects 18
Research Octane Number see RON
Reserve fuel
Message in display 417
Reset button, In instrument cluster 152,
170
Reset tool
Depository 439
Restraint system see Children in the vehi-
cle
Reverse gear position, Automatic
transmission 187, 189
Rims 360, 480
Roadside Assistance 12
Roller sunblind* 204
RON 322
Rubber parts, cleaning 373
Run Flat Indicator 342
S
Safety
Driving safety systems 97
Occupant 68
Reporting defects 18
Safety belts see Seat belts 49