warning MERCEDES-BENZ EQA SUV 2021 Owners Manual

#
Take care toonly connect battery term i-
nals of identical polarity when receiving
starting assistance. #
Obser vethe sequence described for
connecting and disconnecting the jump
leads when receiving starting assistance. #
Do not connect or disconnect the bat-
te ry term inals while the engine is run-
ning. &
W
WARNI NG
ARNI NGRisk of explosion due toexplo-
sive mixture of gases
An explosive mixture of gases can escape
from the battery during charging and starting
assis tance. #
Fire , naked 0ames, smoking and creating
spar ksmust be avoided. #
Make sure there is adequate ventilation. #
Do not stand overth e batter y. &
W
WARNI NG
ARNI NGRisk of explosion from a frozen
battery
A dischar ged battery may freeze at temp era-
tures slightly abo veor below freezing point.
During starting assistance or battery charging,
battery gas can be released. #
Always allow a battery tothaw before
ch arging it or per form ing starting assis-
ta nce. If
th e indicator/warning lamps in the instrument
cluster do not light up at low temp eratures, it is
ve ry likely that the dischar ged battery has frozen.
In this case you may neither jump-start theve hi-
cle nor charge the batter y.
The service life of a bat tery that has been thawed
may be dramatically shor tened. The starting char-
acteristics may be impaired, especially at low
te mp eratures.
It is recommended that you ha veath awe d battery
ch ecked at a quali/ed specialist workshop. All v
All v ehicles
ehicles
* NO
NOTE
TEDamage caused bynume rous or
ex tended attem ptsto start the engine Numerous or
extended attem ptsto start the
engine may damage the catalytic con verter
due tonon-combusted fuel. #
Avoid numerous and extended attem pts
to start the engine. Obser
vethefo llowing points during starting assis-
ta nce and when charging the batter y:
R Only use undamaged jump lead/charging
cables with a su1cient cross-section and
insulated term inal clamps.
R Non-insulated parts of thete rm inal clamps
must not come into contact with other me tal
parts while the jump lead/charging cable is
connected tothe battery/jump-start connec-
tion point.
R The jump lead/charging cable must not come
into contact with any parts which may mo ve
when the engine is running. 322 322
Breakdown assistance

&
W
WARNI NG
ARNI NGRisk of accident due tolimited
saf ety-re lated functions during theto wing
process
Saf ety-re lated functions are limited or no lon-
ge rav ailable in thefo llowing situations:
R theve hicle is switched o..
R the brake system or po wer steering system
is malfunctioning.
R the energy supply or the on-board electri-
cal system is malfunctioning. #
In such cases, do not tow theve hicle. #
Transpo rttheve hicle (/ page 326).
* N
NOOTE
TE Damage tothe drive system due to
incor rect towing The
vehicle may not be towe d in thefo llowing
situations:
R theve hicle is switched o..
R the brake system or po wer steering system
is malfunctioning. R
the energy supply or the on-board electri-
cal system is malfunctioning. #
In such cases, do not tow theve hicle. *
N
NOOTE
TE Damage due toexcessive tractive
po wer If
yo u pull away sharpl y,the tractive po wer
may be too high and theve hicles could be
damaged. #
Pull away slo wlyand smoo thly. Loading t
Loading t
he v
he vehicle f
ehicle f or tr
or transport
anspo rt #
Obser vethe no tes on towing away
( / page 323). #
Connect theto wing device totheto wing eye
in order toload theve hicle. #
ShiT the transmission toposition i.
% The transmission may be loc ked in position
j intheev ent of damage tothe electrics. To
shiT toi , pr ovide the on-board electrical
system with po wer (/ page 323). #
Load theve hicle onto the transpor ter. #
ShiT the transmission toposition j. #
Use the electric parking brake tosecure the
ve hicle against rolling away. #
Only secure theve hicle bythe wheels.
V
V ehicles wit
ehicles wit h adap
h adaptiv
tiv e dam
e dam ping adjus
ping adjustment tment &
W
WARNING
ARNING Risk of an accident when trans-
porting vehicles with adaptive damping
adjustment
When transpo rting vehicles with adaptive
damping adjustment, theve hicle/trailer com-
bination may begin torock and start toskid. #
Load theve hicle cor rectly onto the
transpor ter. #
Secure theve hicle on all four wheels
with suitable tensioning straps. #
Do not exceed the maximum permissible
speed of 60 km/h when transporting. 326
326
Breakdown assistance

#
Make sure that co ver1 engages in the
bumper when youre mo vetheto wing eye.
* N
NOOTE
TE Damage totheve hicle due toincor-
re ct use of theto wing eye or trailer hitch When a
towing eye or trailer hitch is used to
re co ver a vehicle, theve hicle may be damaged
in the process. #
Only use theto wing eye or trailer hitch to
to w awa y or tow start theve hicle. #
Do not use theto wing eye or trailer hitch
to to wtheve hicle during reco very. T
T
o
o w
w -st
-st ar
arting t
ting t he v
he vehicle
ehicle #
Ifth e drive system does not start, ha vethe
ve hicle transpor tedto aqu ali/ed specialist
wo rkshop, e.g. a Mercedes-Benz Se rvice
Centre. #
The drive system cannot be star tedby tow-
starting theve hicle. Do not per form any
attem ptsto to w-start theve hicle. Electr
Electr
ical fuses
ical fuses N
No
ot
tes on electr
es on electr ical fuses
ical fuses &
W
WARNING
ARNING Risk of accident and injury due
to ove rloaded lines
If yo u manipulate or bridge a faulty fuse or if
yo ure place it with a fuse with a higher amper-
age, the electric line could be overloaded.
This could result in a /re. #
Alwaysre place faulty fuses with speci-
/ed new fuses containing the cor rect
amperage. *
N
NOOTE
TE Damage due toincor rect fuses Electrical components or systems may be
damaged
byincor rect fuses, or their function-
ality may be signi/cantly impaired. #
Only use fuses that ha vebeen appr oved
by Mercedes-Benz and which ha vethe
cor rect fuse rating. Blown fuses must be
replaced with fuses of the
same rating, whi chyou can recognise bythe col- our and
the label. The fuse ratings and fur ther
information tobe obser ved can be found in the
fuse assignment dia gram.
F F use assignment diagr
use assignment diagr am:
am:onthe fuse box in the
engine compartment (/ page 329).
* NO
NO TE
TEDamage or malfunctions caused by
moisture Moisture may cause damage
tothe electrical
system or cause it tomalfunction. #
When the fuse box is open, make sure
th at no moisture can enter the fuse box. #
When closing the fuse box, make sure
th at the seal of the lid is positioned cor-
re ctly on the fuse box. If
th e ne wlyinser ted fuse also blo ws, ha vethe
cause traced and recti/ed at a quali/ed specialist
wo rkshop.
Ensure thefo llowing before replacing a fuse:
R The vehicle is secured against rolling away.
R All electrical consume rsare switched o..
R The vehicle is switched o.. 328
328
Breakdown assis
tance

The electrical fuses are located in
various fuse
bo xes:
R Fuse box in the engine compartment on the
leT-hand side of theve hicle, when vie wed in
th e direction of tr avel (/ page 329)
R Fuse box in the front passenger foot we ll
(/ page 330)
R Fuse box in the centre of the load compart-
ment (/ page 331) Opening and closing t
Opening and closing t
he fuse bo
he fuse box in t
x in the engine
he engine
com
com par
partment
tment R
R
eq
eq uir
uir ements:
ements:
R A dry clo thand a scr ewdriver are available.
Obser vethe no tes on elect rical fuses
(/ page 328). Opening
Opening &
W
WARNING
ARNING Risk of injury from using the
windscreen wipers when the bonnet is
open
If th e windscreen wipers start moving when
th e bonnet is open, you could be trapped by
th e wiper linkage. #
Always switch o. the windscreen wipers
and vehicle before opening the engine
bonnet. #
Open the bonnet. #
Remo veany existing moisture from the fuse
box using a dry clo th. #
Loosen scr ews1. #
Press clamps 2and liT the fuse box lid up
and out.
The fuse assignment diag ram is in a recess on the
side of the fuse box. Breakdown assistance
329
329

N
N
o
ot
tes on noise or unusual handling c
es on noise or unusual handling c har
har act
acter
eris-
is-
tics
tics
Make sure there are no vibrations, noises or
unusual handling characteristics when theve hicle
is in motion. This may indicate that the wheels or
tyres are damaged. Hidden tyre damage could
also be causing the unusual handling characteris-
tics.
If yo u suspect that a tyre is defecti ve,re duce your
speed immediately and ha vethe tyres and wheels
ch ecked at a quali/ed specialist workshop. N No
ot
tes on r
es on r egularl
egularly inspecting wheels and tyr
y inspecting wheels and tyr es
es&
W
WARNING
ARNING Risk of injury due todamaged
tyres
Damaged tyres can cause tyre pressure loss. #
Check the tyres regula rly fo r signs of
damage and replace any damaged tyres
immediatel y. &
W
WARNI NG
ARNI NGRisk of aquaplaning due to
insu1cient tyre tread
Insu1cient tyre tread will result in reduced
tyre grip.
The risk of aquaplaning is increased on wet
ro ads, especially when the speed of theve hi-
cle is not adap tedto suit the conditions. #
Thus, you should regula rly ch eck the
tread dep thand the condition of the
tread across the entire width of all tyres.
Minimum tread dep thfor:
R Summer ty res: 3 mm
R M+S tyres: 4 mm #
For saf etyre asons, replace the tyres
before the legall y-prescribed limit forthe
minimum tread dep thisreached. Car
ryout thefo llowing checks on all wheels regu-
lar ly, at least once a month or as required, for
ex ample, prior toa long jou rney or driving o.-
ro ad:
R Check the tyre pressure (/ page 333). R
Visually inspect wheels and tyres for damage.
R Check theva lve caps.
R Visual check of the tyre tread dep thand the
tyre contact sur face across the entire width.
The minimum tread dep thfor summer tyres is
3 mm and for winter tyres 4 mm. N
No
ot
tes on sno
es on sno w c
w chains
hains &
W
WARNING
ARNING Risk of accident due toincor-
re ct snow chain /tting
If yo u /t snow chains tothere ar wheels, the
snow chains may grind against theve hicle
body or chassis components.
This could cause damage totheve hicle or the
tyres. #
Never /t snow chains tothere ar wheels. #
Always /t snow chains tothe front
wheels in pairs. 332
332
Wheels and tyres

*
N
N O
OTE
TE Damage tovehicle body or suspen-
sion components caused by/tted snow
ch ains On 4MATIC
vehicles, if you /t snow chains on
th ere ar wheels, you can damage vehicle body
or suspension components. #
On 4MATIC vehicles, only /t snow chains
on the front wheels. Obser
vethefo llowing no tes when using snow
ch ains:
R Snow chains are only permissible for cer tain
wheel/tyre combinations. You can obtain
information about this from a Mercedes-Benz
Service Centre.
R For saf etyre asons, only use snow chains that
ha ve been speci/cally appr oved foryo ur vehi-
cle byMercedes-Benz, or snow chains with
th e same quality standard.
R If snow chains are /tted, the maximum per-
missible speed is 50 km/h. R
V
V ehicles wit
ehicles wit h A
h Activ
ctiv e P
e Par
arking Assist
king Assist: :do not use
Ac tive Parking Assist when snow chains are
/tted.
% You can permanently limit the maximum
speed for driving with winter tyres
(/ page 199).
% You can deactivate ESP ®
to pull away
( / page 192). This allo ws the wheels tospin,
achieving an increased driving forc e. T
T
yr
yr e pr
e pr essure
essure N
No
ot
tes on tyr
es on tyr e pr
e pressure
essure &
W
WARNING
ARNING Risk of accident due toinsu1-
cient or excessive tyre pressure
Un derin0a tedorove rin0ated ty res pose in par-
ticular thefo llowing risks:
R The tyres can burst.
R The tyres can wearexcessively and/or
une venly. R
The driving characteristics as well as the
stee ring and braking characteristics may
be greatly impaired. #
Comply with there commended tyre
pressure and check the tyre pressure of
all tyres, including the spare wheel, regu-
lar ly:
R monthly
R when the load changes
R before embarking on a lon ger journey
R if operating conditions change, e.g. o.-
ro ad driving #
Adjust the tyre pressure, if necessar y. Ty
re pressure which is too high or too low can:
R Shor tenth e service life of the tyres.
R Cause increased tyre damage.
R Adve rsely a.ect driving characteristics and
th us driving saf ety, e.g. due toaquaplaning. Wheels and tyres
333
333

R
Tyre pressure monitor active :th ete ach-in
process of the system is not yetcomple te. The
tyre pressures are already being monitored. #
Compare the tyre pressure with there com-
mended tyre pressure forth e cur rent ope rat-
ing condition (/ page 334).Additionall y,
obser vethe no tes on cold tyres
(/ page 333).
% The values displa yed in the on-board com-
puter may deviate from those of the tyre pres-
sure gauge as they referto sea le vel.At high
ele vations, the tyre pressure values indicated
by a pressure gauge are higher than those
shown bythe on-board computer. In this case,
do not reduce the tyre pressure.
R
R est
est ar
arting t
ting t he tyr
he tyr e pr
e pressur
essur e monit
e monit or
oring syst
ing syst em
em
R
R eq
eq uir
uir ements:
ements:
R The recommended tyre pressure is cor rectly
set forth ere specti veoperating status on all of
th e wheels (/ page 333).
Re start the tyre pressure monitoring system in the
fo llowing situations:
R The tyre pressure has changed. R
The wheels or tyres ha vebeen changed or
ne wly /tted.
On-board computer: 4 Service 5
Tyres #
Swipe down wards on Touch Control on the
leT-hand side of the steering wheel.
The Use current pressures as new reference
values? message is shown in the Instrument
Displa y. #
Torestart, press Touch Control on the leT-
hand side of the steering wheel.
The Tyre press. monitor restarted message is
shown in the Instrument Displa y.
Cur rent wa rning message s are deleted and
th eye llow h warning lamp goes out.
ATer you ha vebeen driving for a few minutes,
th e system checks whe ther the cur rent tyre
pressures are within the speci/ed range. The
cur rent tyre pressures are then accep ted as
re fere nce values and monitored.
Be sure toalso pay attention tothefo llowing rela-
te dto pic:
R Notes on tyre pressure (/ page 333) Wheel c
Wheel c
hange
hange N
No
ot
tes on selecting,
es on selecting, /tting
/ttingand r
and replacing tyr
eplacing tyr es
es &
W
WARNING
ARNING Risk of accident due toincor-
re ct wheel and tyre dimensions
If wheels and tyres of the wrong size are /t ted,
th e service brakes or components in the brake
system and in the wheel suspension may be
damaged. #
Alwaysre place wheels and tyres with
th ose that ful/l the speci/cations of the
original part.
Fo r wheels, pay attention tothefo llowing:
R Designation
R Type
Fo r tyres, pay attention tothefo llowing:
R Designation
R Manufacturer
R Type 336
336
Wheels and tyres

R
Only /t wheels of the same size on one axle
(leT and right).
It is only permissible to/t a di.e rent wheel
size in theev ent of a 0at tyre in order todrive
to the specialist workshop.
R Do not make any modi/cations tothe brake
system, the wheels or the tyres.
The use of shims or brake dust shields is not
permitted and may in validate theve hicle's
ge neral ope rating permit.
R V
Vehicles wit
ehicles wit h a tyr
h a tyre pr
e pressur
essur e monit
e monit or
oring sy
ing sy s-
s-
t
t em:
em: all /t tedwheels must be equipped with
functioning sensors forth e tyre pressure mon-
itoring system.
R Attemp eratures below 7 °C use winter tyres
or all-season tyres mar kedi M+Sfor all
wheels.
Wi nter tyres pr ovide the best possible grip in
wintry road conditions.
R For M+S tyres, only use tyres with the same
tread.
R Obser vethe maximum permissible speed for
th e M+S tyres /t ted. If
th e tyre's maximum speed is below that of
th eve hicle, this must be indicated byan
appropriate label in the driver's /eld of vision.
R Run in new tyres at moderate speeds forthe
/r st 100 km.
R Replace the tyres aTer six years at the latest,
re ga rdless of wear.
R When r
When r eplacing wit eplacing wit h tyr
h tyres t
es that do no
hat do no t f
t featur
eatur e
e
r
r un-0at
un-0at c
c har
har act
acter
eris
istics:
tics: vehicles with
MOExtended tyres are not equipped with a
TIREFIT kit at thefa ctor y.Equip theve hicle
with a TIREFIT kit aTer replacing with tyres
th at do not feature run-0at characteristics,
e.g. winter tyres.
% You can permanently limit the maximum
speed for driving with winter tyres
(/ page 199).
Fo r more information on wheels and tyres, con-
ta ct a quali/ed specialist workshop.
Be sure toalso obser vethefo llowing fur ther rela-
te d subjects:
R Notes on tyre pressure (/ page 333)
R Tyre pressure table (/ page 334) R
Notes on the emer gency spa rewheel
(/ page 345) N No
ot
tes on int
es on int erc
erchanging wheels
hanging wheels &
W
WARNING
ARNING Risk of injury thro ugh di.erent
wheel sizes
Inter changing the front and rear wheels can
se verely impair the driving characteristics.
The disk brakes or wheel suspension compo-
nents may also be damaged. #
Only inter change the front and rear
wheels if the wheels and tyres ha vethe
same dimensions. Inter
changing the front and rear wheels if the
wheels or tyres ha vedi.erent dimensions can
re nder thege neral ope rating permit in valid.
The wear patterns on the front and rear wheels
di.er:
R front wheels wear more on the tyre shoulder
R rear wheels wear more in the centre of the
tyre Wheels and tyres
339
339

#
Using the wheel wrench, loosen the wheel
bolts on the wheel you wish tochange by
about one full turn. Do not unscr ewthe
scr ews comple tely. Po
sition of jack support points &
W
WARNING
ARNING Risk of injury from inco rrect
positioning of the jack
If yo u do not position the jack cor rectly at the
appropriate jacking point of theve hicle, the
jack could tip wi th theve hicle raised. #
Only position the jack at the appropriate
jacking point of theve hicle. The base of
th e jack must be positioned vertically
under the jacking point of theve hicle. *
N
NOOTE
TE Damage totheve hicle due tousing
an unsuitable jack Yo
u can damage theve hicle and, in particular
th e high-voltage batter y,ifyo u use a jack that
is not speci/cal lydesigned forth e jack sup-
port points of theve hicle. #
Only use jac ksthat are speci/cal ly
designed forth e jack support points, or
use an appropriate adap ter. *
N
NO
OTE
TE Risk of damage totheve hicle due
to incor rect positioning of the jack If
yo u do not position the jack at the designa-
te d jack support points, you could damage
yo ur vehicle and, in particular, the high-voltage
batter y. #
Only position the jack at the designated
jack support points. #
Take thera tchet out of the tyre-change tool kit
and place it on the he xagon nut of the jack so
th at the letters "AUF" are visible. 342
342
Wheels and tyres

&
W
WARNI NG
ARNI NGRisk of accident from losing a
wheel
Oiled or greased wheel bolts can cause the
wheel bolts tocome loose, as too can dam-
aged wheel bolts or wheel hub thre ads. #
Never oil or grease theth re ads. #
Intheev ent of damage totheth re ads,
contact a quali/ed specialist workshop
immediatel y. #
Have the damaged wheel bolts or dam-
aged hub thre ads replaced. #
Do not continue driving. #
Obser vethe information on thech oice of tyres
(/ page 336).
Fo r tyres with a speci/ed direction of rotation, an
ar ro w on the side wall of the tyre indicates the
cor rect direction of rotation. Obser vethe direc-
tion of rotation when /tting. #
Slide the wheel tobe mounted onto the cen-
tring pin and push it on. &
W
WARNING
ARNING Risk of injury from tightening
wheel bolts and nuts
If yo u tighten the wheel bolts or wheel nuts
when theve hicle is raised, the jack could tip. #
Only tighten wheel bolts or wheel nuts
when theve hicle is on thegr ound. #
Be sure toobser vethe inst ructions and saf ety
no tes on "Changing a wheel" (/ page 336). #
For saf etyre asons, only use wheel bolts which
ha ve been appr oved byMercedes-Benz and
fo rth e wheel in question. #
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated until they are
/nger-tight. #
Unscr ewand remo vethe centring pin. #
Tighten the last wheel bolt until it is /n ger-
tight. #
Lowe rth eve hicle (/ page 344). Low Low
er
ering t
ing t he v
he vehicle
ehicle aTer
aTera wheel c
a wheel c hange
hange R
R
eq
eq uir
uir ements:
ements:
R The new wheel has been /tted (/ page 343). #
T
To low
o low er t
er the v
he v ehicle:
ehicle: placethera tchet onto
th e he xagon nut of the jack so that the letters
"AB" are visible and turn anti-clockwise. #
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated 1to5 with
an initial maximum forc e of 80 Nm. #
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated 1to5 with
th e speci/ed tightening torque of 150 Nm. 344
344
Wheels and tyres