ABS MERCEDES-BENZ EQC SUV 2022 Owners Manual

1
Speedom eter →
251
2 #! Turn signal lights →
128
3 Multifunction display →
253
4 õ Operational readiness of drive system →
154
5 R Rear fog light →
128
6 K High beam →
128
L Low beam →
127
T Standing lights →
127
7 Ú System er ror →
415
8 Powe rav ailability displ ay →
251
9 L Distance warning →
420
A ü Seat belt →
414
B h Tyre pressure monitoring system →
423
C Ù Powe r steering →
416 D
! Electric parking brake (yellow) →
418
E ï Trailer hitch →
416
F ! Electric parking brake (red) →
418
G 6 Restraint system →
414
H J Brakes (red) →
418
I Char geleve l display →
251
J R Range →
251
K J Brakes (yellow) →
418
L # Electrical fault →
415
M _ Reduced po wer →
415
N ! ABS →
420
O å ESP®
OFF →
420
÷ ESP®
→
420 At
a glance – Indicator and warning lamps
9
9

R
theve hicle is driven toofast ove r an obsta-
cle, e.g. a kerb, speed bump or po thole
R a heavy object st rike sth e underbody or
suspension components
In situations such as these, damage tothe
body, underbody, suspension components,
wheels or tyres and high-voltage battery com-
ponents may not be visible. Components dam-
aged in this wa y can un expectedly fail or, in
th e case of an accident, may no longer absorb
th ere sulting forc e as intended. #
Have theve hicle checked and repaired
immediately at a quali/ed specialist
wo rkshop.
or #
If driving saf ety is impaired while con-
tinuing your journe y,pull over and stop
th eve hicle immediatel y,while paying
attention toroad and tra1c conditions,
and contact a quali/ed specialist work-
shop. Elect
ric ve hicles ha vean elect ric mo tor.The elec-
tric mo tor's energy supply is pr ovided bythe high-
vo ltage on-board electrical system. &
D DAN
AN GER
GER Risk of death and /re due to
modi/ed and/or damaged components of
th e high-voltage on-board electrical sys-
tem
The vehicle's high- voltage on-board electrical
system is under high voltage. If you modify
component parts in theve hicle's high- voltage
on-board electrical system or touch damaged
component parts, you may be electrocuted. In
addition, modi/ed and/or damaged compo-
nents may cause a /re.
In theeve nt of an accident or impact tothe
ve hicle underbod y,components of the high-
vo ltage electrical system may be damaged
although the damage is not visible. #
Never make any modi/cations tothe
high- voltage on-board electrical system. #
Do not switch on or use theve hicle if its
high- voltage on-board electrical system components ha
vebeen modi/ed or dam-
aged. #
Neverto uch damaged components of
th e high-voltage on-board electrical sys-
te m. #
ATer an accident, do not touch any com-
ponents of the high-voltage on-board
electrical system. #
ATer an accident, ha vetheve hicle trans-
por tedawa y. #
Have the components of the high-voltage
on-board electrical system checked at a
qu ali/ed specialist workshop and
re placed if necessar y. The components of
theve hicle's high- voltage on-
board electrical system are mar ked with yellow
wa rning stic kers. The cables of the high-voltage
on-board electrical system are orange. 22 22
General no
tes

T
T
ec
ec hnology Fr
hnology Freq
eq uency r
uency r angeT r
ang eT ransmission output/magne
ansmission output/magne tic
tic/eld
/eld s
strtr eng th
ength
UMTS (Band I, III, VIII)+ 24 dBm (+1/-3 dB)
LT E (Band 1, 3, 7, 8, 20, 28) +23 dBm (±2 dB)
RAMSES (Router And Mobile SErviceS )GSM (E-GSM 850 / E-GSM 900, Class 4)
GSM (E-GSM 1800 / E-GSM 1900, Class 4) < +32.5 dBm (±1 dB)
< +29.5 dBm (±1 dB)
UMTS (WCDMA FDD I, II, III, IV, V,VIII, XIX, Class
3) < +23.5 dBm (±1 dB)
LT E (FDD B1, B2, B3, B4, B5, B7, B8, B9, B18,
B19, B21, B28, Class 3) < +23 dBm (±1 dB)
LT E (TDD B38, B40, B41, Class 3) < +23 dBm (±1 dB)
GNSS (1559–1610 MHz )R eceiving onlyInf Inf
or
ormation about t
mation about t he
hespeci/c
speci/c absorp
absorption r
tion rate
ate
Fo rFr ance onl y:
The values weredeterm ined and tested in acco rd-
ance with the Décr etn° 2019-1186 guideline
re ga rding the indication of the speci/c absor ption
ra te (SAR) of wireless vehicle components. Fu
rther information and updates are available at
th efo llowing web address:
https://moba.i.daimler.com/baix/cars/SAR/
fr_FR/index.html 28 28
General no
tes

Inf
Inf
or
ormation about t
mation about t he
hespeci/c
speci/c absorp
absorption r
tion r ate
ate V
V
ehicle com
ehicle com ponentsS
ponent sS AR v
AR value in W/kg
alue in W/kg Applicable limit v
Applicable limit value
alue
Compensator ECE DE003 & ECE DE004 < 0.2 W/kg 2 W/kg
DA I RS E1 .8 W/kg 2 W/kg
HERMES communication module < 0.4 W/kg2 W/kg General no
tes
29
29

#
If necessar y,slide head restraint 1upwa rds
( / page 102). #
Fitth e ISOFIX or i‑Size child restraint system
wi th TopTe ther. In doing so, comply with the
ch ild restraint system manufactu rer's installa-
tion inst ructions. #
Guide TopTe ther belt 5under head restraint
1 between the two head restraint ba rs. #
Guide TopTe ther belt 5down wards between
combined lug gage cover and net 3and seat
backrest 2. #
Hook TopTe ther hook 6ofTopTe ther belt
5 into TopTe ther anchorage 4without
twisting. #
Tension TopTe ther belt 5. In doing so, com-
ply with thech ild restraint system manufactu r-
er's installation inst ructions. #
If necessar y,slide head restraint 1down-
wa rds (/ page 102). Make sure that you do
not inter fere with the cor rect routing of To p
Te ther belt 5. Secur
Secur
ing t
ing the c
he child r
hild r es
estrtraint syst
aint syst em wit
em with t
h the seat
he seat
belt
belt N
No
ot
tes on t
es on t he suit
he suitability of seats f
ability of seats f or att
or attac
aching belt-
hing belt-
secur
secur ed c
ed child r
hild r es
estrtraint syst
aint syst ems
ems
R
R ear seats
ear seats
W
W eight cat
eight cat egor
egory 0: t
y 0: t o 10 kg
o 10 kg
LeT/ right rear seat U, L
Centre rear seat 1
U, L
W
W eight cat
eight cat egor
egory 0+: t
y 0+: t o 13 k
o 13 kg g
LeT/right rear seat U, L
Centre rear seat 1
U, L
W
W eight cat
eight cat egor
egory I: 9 t
y I: 9 t o 18 kg
o 18 kg
LeT/right rear seat U, L
Centre rear seat 1
U, L
W
W eight cat
eight cat egor
egory II: 15 t
y II: 15 t o 25 k
o 25 kgg
LeT/right rear seat U, L Centre
rear seat 1
U, L
W
W eight cat
eight cat egor
egory III: 22 t
y III: 22 t o 36 kg
o 36 kg
LeT/right rear seat U, L
Centre rear seat 1
U, L
1 Child restraint systems wi th a supporting brac ket are not suitable
fo rth is seat.
U Suitable forch ild restraint systems of the "Universal" category in
th is we ight categor y.
L Suitable for semi-universal child restraint systems acco rding to
th eta ble in "Recommended child restraint systems", or if thevehi-
cle and the seat are listed in thech ild restraint system manufactur-
er's vehicle model list. N
No
ot
tes on c
es on c hild r
hild res
estrtraint syst
aint syst ems on t
ems on t he fr
he front
ont
passeng
passeng er seat
er seat
R If it is absolutely necessary foryo uto /t a
ch ild restraint system tothe front passenger
seat, be sure toobser vethe information on
ch ild restraint systems on the front passenger
seat (/ page 69). Occupant saf
ety
65
65

lamp is o.,
the front passenger airbag can
deploy in theev ent of an accident.
The child could be struck bythe airbag. #
Always ensu rethat the front passenger
airbag is disabled. The PASSENGER AIR
BAG OFF indicator la mpmust be lit. #
NEVER use a rear wa rd-facing child
re straint system on a seat wi than ENA-
BLED FRONT AIR BAG. This can result in
th e DEATH of or SERIOUS INJURY tothe
CHILD. Obse
rveth e speci/c inst ructions forth ere ar-
wa rd-facing and forw ard-facing child restraint sys-
te ms (/ page 69). Wa
rning notice on the front passenger sun visor
Alw ays obser vethe status of the front passenger
airbag on thePA SSENGER AIR BAG OFF indicator
la mp:
R If it is absolu tely necessary to/t a child
re straint system tothe front passenger seat,
alw ays obser vethe information on automatic
front passenger airbag shuto. (/ page 48).
R When using a rear wa rd-facing child restraint
system on the front passenger seat, the front
passenger airbag must alw ays be disabled.
This is only the case if thePA SSENGER AIR
BAG OFF indicator la mpis lit continuously
(/ page 49). R
Ifth ePA SSENGER AIR BAG OFF indicator
la mp is o., the front passenger airbag is ena-
bled. The front passenger airbag may deploy
during an accident.
Secur
Secur ing t ing the c
he child r
hild r es
estrtraint syst
aint syst em wit
em with t
h the seat
he seat
belt on t
belt on t he fr
he front passeng
ont passeng er seat
er seat
When /tting a belt-secured child restraint system
on the front passenger seat, alw ays obser vethe
fo llowing:
O Obser vethe no tes on rear wa rd-facing and
fo rw ard-facing child restraint systems on the
front passenger seat (/ page 68).
O Obser vethech ild restraint system manufac-
tu re r's installation and operating inst ructions.
O For a child restraint system in the "Universal"
or "Semi-Universal" categor y,make sure that
th e system has been appr ovedfo rth eve hicle
seat.
Obser vethe no tes under "Suitability of seats
fo r attaching belt-secured child restraint sys-
te ms" (/ page 65). Occupant saf
ety
69 69

#
Obser vethe saf ety no tes in the operat-
ing inst ructions forth ewa llbox. If
ch arging at a wallbox without pre-ins talled
cable, use the optionally available charging cable
fo rwa llbox and charging station (mode 3). The
ch arging cable is st owed in a bag in the boot/
luggage compartment.
Only use charging cables that ha vebeen tested
and appro vedby the manufacturer forch arging
th e high-voltage battery in an electric vehicle. &
D DAN
AN GER
GER Risk of fatal injuries due todam-
aged components
Connecting thech arging cable toach arging
station using a damaged component part
could cause a /re or an elect ric shoc k,for
ex ample. #
Forch arging stations with a preinstalled
ch arging cable:
R Perform a visual check of thech arg-
ing station for obvious faults, such as
massive damage tothe housing or
ch arging cable. #
Forch arging stations without a preinstal-
led charging cable:
R For saf etyre asons, only use charging
cables that ha vebeen tested and
appro vedby the manufacturer for
ch arging the high-voltage battery in
an electric vehicle.
R Never use damaged charging cables.
R Do not extend thech arging cable.
R Do not use adap ters. #
Make sure toobser vethe saf ety in form a-
tion on thech arging station. Most
charging stations must be activated before
th ech arging process, e.g. using an RFID card.
Obser vethe on-site operator's inst ructions forthe
ch arging station.
The amount of ene rgy dispensed forth ech arging
process, shown bythech arging station, may be
higher than the amount of energy actually absor-
bed bythe high-voltage batter y.This is there sult
of di.erent le vels of charging losses and is descri-
bed as rech arge e1ciency. Charging losses occur,
fo rex ample, due toheat that builds up when ch
arging or from auxiliary consumers that are
switched on. Further information on rech arge e1-
ciency can be obtained at a quali/ed specialist
wo rkshop. N No
ot
tes on c
es on c har
harging t
ging t he high-v
he high-v olt
oltag
age batt
e batt er
ery at a
y at a
r
r apid c
apid c har
harging st
ging st ation (mode 4)
ation (mode 4) &
D
DAN
AN GER
GER Risk of fatal injuries due todam-
aged components
Connecting thech arging cable toach arging
station using a damaged component part
could cause a /re or an elect ric shoc k,for
ex ample. #
Forch arging stations with a preinstalled
ch arging cable:
R Perform a visual check of thech arg-
ing station for obvious faults, such as
massive damage tothe housing or
ch arging cable. #
Forch arging stations without a preinstal-
led charging cable:
R For saf etyre asons, only use charging
cables that ha vebeen tested and Driving and pa
rking
171
171

appr
oved bythe manufacturer for
ch arging the high-voltage battery in
an electric vehicle.
R Never use damaged charging cables.
R Do not extend thech arging cable.
R Do not use adap ters. #
Make sure toobser vethe saf ety in form a-
tion on thech arging station. &
D
DAN
AN GER
GER Risk of fatal injuries when car ry-
ing out maintenance workduring the
ch arging process
During thech arging process, the high-voltage
on-board electrical system is under high volt-
age. #
Do not per form any main tenance work
during thech arging process. Most
charging stations must be activated before
th ech arging process, e.g. using an RFID card.
Obser vethe on-site operator's inst ructions forthe
ch arging station. The
charging cable forth eve hicle must not be
lon gerth an 30 m due tothe legal requ irements in
some countries. This is toprev ent the inter fer-
ence of signals being received byradio communi-
cation devices in theve hicle or in close pr oximity
to thech arging station. Be awarethat parts of the
ch arging cable may be routed under ground. If in
doubt, ask thech arging station operator if this is
th e case before charging the high-voltage batter y.
The amount of energy dispensed forth ech arging
process, shown bythech arging station, may be
higher than the amount of energy actually absor-
bed bythe high-voltage batter y.This is there sult
of di.erent le vels of charging losses and is descri-
bed as rech arge e1ciency. Charging losses occur,
fo rex ample, due toheat that builds up when
ch arging or from auxiliary consumers that are
switched on. Further information on rech arge e1-
ciency can be obtained at a quali/ed specialist
wo rkshop. Se
Se
tting t
tting t he maximum per
he maximum per missible c
missible char
harging cur-
ging cur-
r
r ent f
ent f or c
or char
harging at a mains soc ket
ging at a mains soc ket *
N
NO
O TE
TE Overloading the mains soc ket due
to excessive charging cur rent If
th ech arging cur rent is too high, the fuse
could be tripped or theex tern al mains supply
could overheat. #
Make sure that theex tern al mains supply
has been designed tohandle the set
ch arging cur rent. #
If necessar y,reduce the set charging
cur rent or use a di.erent mains soc ket. #
For saf etyre asons, only use thech arging
cable supplied with theve hicle or an
original Mercedes-Benz charging cable.
Mercedes-Benz thoroughly tests these
original charging cables forth eir suitabil-
ity for high-voltage charging of your vehi-
cle. Pur chase these parts at a Mercedes-
Benz Service Centre and obtain advice
th ere. 172 172
Driving and parking

1
Multifunction camera
2 Cameras in the outside mir rors
3 Front radar
4 Front camera
5 Corner radars
6 Ultrasonic sensors
7 Reversing camera &
W
WARNING
ARNING Risk of accident due torestric-
te d de tection per form ance of vehicle sen-
sors and cameras
If th e area around vehicle senso rsor cameras
is co vered, damaged or dirty, cer tain driving
and saf ety sy stems cannot function co rrectl y.
There is a risk of an accident. #
Keep the area around vehicle senso rsor
cameras clear of any obst ructions and
clean. #
Have damage tothe bumper, radiator
gr ille or stone chipping in the area of the
front and rear wind owsre paired at a
qu ali/ed specialist workshop. Pa
rticular ly,ke ep the areas around the sensors
and cameras free of dirt, ice or slush
(/ page 312). The sensors and cameras must
not be co vered and the de tection ranges around
th em must be kept free. Do not at tach additional
licence plate brac kets, advertisements, stic kers,
fo ils or foils toprotect against stone chippings in
th e de tection range of the sensors and cameras. Make sure
that there are no overhanging loads
pr otru ding into the de tection range.
If th ere is damage toa bumper or thera diator
gr ille, or aTer an impact, ha vethe function of the
senso rschecked at a quali/ed specialist work-
shop. Ha vedamage or stone chipping in the area
of the cameras on the front and rear wind ows
re paired at a quali/ed specialist workshop. Ov Ov
er
ervie
vie w of dr
w of dr iving syst
iving syst ems and dr
ems and dr iving safe
iving safety
ty
syst
syst ems
ems R
ABS (A Anti-lock B Braking S System) (/ page 193)
R BAS (BBra ke AAssist S System) (/ page 193)
R ESP ®
(EElectronic S Stability P Program)
(/ page 194)
R ESP ®
Crosswind Assist (/ page 195)
R ESP ®
trailer stabilisation (/ page 195)
R EBD (E Electronic B Brakeforc e DDistribution)
(/ page 196)
R STEER CONTROL (/ page 196)
R HOLD function (/ page 196)192
192
Driving and parking

R
Hill Start Assist (/ page 198)
R Adaptive Brake Lights (/ page 198)
R ATTENTION ASSIST (/ page 198)
R Cruise cont rol (/ page 200)
R Limiter (/ page 200)
R Tra1c Sign Assist (/ page 218)
R Speed Limit Assist (countr y-dependent)
(/ page 216)
Dr
Dr iving Assist
iving Assist ance pack
ance package
age
The following functions are part of the Driving
Assistance Package. Cer tain functions are only
av ailable in some countries. Some functions are
also available without the Driving Assistance
Pa ckage, albeit with restric ted functionality.
R Active Distance Assist DISTRONIC
(/ page 203)
R Active Speed Limit Assist (countr y-dependent)
(/ page 207)
R Route-based speed adap tation (countr y-
dependent) (/ page 207)
R Active Brake Assist (/ page 212) R
Active Steering Assist (countr y-dependent)
(/ page 209)
R Active Emer gency Stop Assist (countr y-
dependent) (/ page 211)
R Blind Spot Assist and Active Blind Spot Assist
with exitwa rning (/ page 220)
R Active Lane Keeping Assist (/ page 223)
P
P ar
ar king P
king P ack
ackage
age
R Reversing camera (/ page 225)
R 360° Camera (/ page 228)
R Parking Assist PARKTRONIC (/ page 232)
R Active Parking Assist (/ page 235) F
F
unction of ABS
unction of ABS The Anti-lock Brake System (ABS)
regula testhe
brake pressure in critical driving situations:
R During braking, for instance, at maximum full-
stop braking or if there is insu1cient tyre trac-
tion, the wheels are pr evented from locking.
R Vehicle steerability while braking is ensu red. If ABS inter
venes when braking, you will feel a
pulsing in the brake pedal. The pulsating brake
pedal can be an indication of hazardous road con-
ditions and can ser veas a reminder totake extra
care while driving.
Syst
Syst em limits em limits
R ABS is acti vefrom speeds of approx. 8 km/h.
R ABS may be impaired or may not function if a
malfunction has occu rred and theye llow !
ABS warning lamp lights up continuously in
th e inst rument cluster aTer the drive system is
star ted. F F
unction of B
unction of B AS
AS &
W
WARNING
ARNING Risk of an accident caused by a
malfunction in BAS(Brake Assist System)
If BAS is malfunctioning, the braking distance
in an emer gency braking situation is
increased. #
Dep ress the brake pedal with full forc e in
emer gency braking situations. ABS pre-
ve nts the wheels from locking. Driving and parking
193
193