hood open MERCEDES-BENZ G-Class 2012 W463 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2012, Model line: G-Class, Model: MERCEDES-BENZ G-Class 2012 W463Pages: 284, PDF Size: 9.4 MB
Page 10 of 284
Fuel
Additives ........................................ 274
Important safety notes
..................273
Premium-grade unleaded gasoline . 273
Refueling ........................................ 124
Specifications ................................ 274
Troubleshooting ............................. 127
Fuel/water separator
Service ........................................... 216
Fuel consumption
Notes ............................................. 129
Fuel filler cap (display message) .....174
Fuel filler flap Emergency release ........................ 126
Opening/closing ............................ 125
Fuel filter
Display message ............................ 174
Fuel level
Calling up the range (on-board
computer) ...................................... 163
Fuse allocation chart ........................238
Fuse box Battery case ................................... 239
Dashboard ..................................... 238
Front-passenger footwell ...............238
Transmission tunnel ....................... 239
Fuse extractor ................................... 238
Fuses Dashboard fuse box ....................... 238
Fuse allocation chart ..................... 238
Fuse box in the front-passenger
footwell .......................................... 238
Fuse box in the transmission
tunnel ............................................ 239
In the battery case ......................... 239
Notes ............................................. 237G
Garage door opener Clearing the memory
.....................207
Notes ............................................. 204
Opening/closing the garage door ..207
Programming the remote control ... 205
Gear or selector lever (cleaning
guidelines) ......................................... 221
Genuine Mercedes-Benz parts ......... 270Genuine wood trim and trim strips
(cleaning instructions)
......................221
Glove box ........................................... 189
Gradient-climbing capability
(maximum) ......................................... 139
GTW (Gross Trailer Weight)
(definition) ......................................... 263 H
Handbrake see Parking brake
Hazard warning lamps ........................91
Headlamp delayed switch-off see Exterior lighting delayed switch-off
Headlamps
Adding fluid to cleaning system .....214
Cleaning ......................................... 220
Cleaning system (function) .............. 91
Fogging up ....................................... 92
Protective grille ................................ 98
Headlamps (automatic) ......................89
Head restraints Adjusting (angle) .............................. 77
Adjusting (rear) ................................ 78
Installing/removing (rear) ................ 78
Luxury .............................................. 79
Resetting (front) ............................... 78
see NECK-PRO head restraints
Heating
see Climate control
Heating, windshield
see Windshield heating
High beam flasher ............................... 91
High-beam headlamps (display
message) ............................................ 169
High-mounted brake lamp Display message ............................ 168
Hill start assist .................................. 117
Hood Closing ........................................... 211
Display message ............................ 177
Opening ......................................... 210
Hydroplaning ..................................... 1328
Index
Page 26 of 284
Cockpit
Function Page
:
Combination switch 91
;
Cleans the headlamps 91
=
Cruise control lever 139
?
Horn
A
Instrument cluster 25
B
Voice Control System lever;
see the separate operating
instructions C
Ignition lock 115
D
Glove box lock
189 Function Page
E
Glove box 189
F
Center console 28
G
Multifunction steering
wheel
27
H
Diagnostics socket 20
I
Opens the hood 210
J
Adjusts the steering wheel 81
Steering wheel heating
K
Light switch 88
L
Adjusts the exterior mirrors 8424
Cockpit
At a glance
Page 59 of 284
!
Avoid spinning the driven wheels for an
extended period with ESP ®
deactivated.
You could
otherwise damage the drivetrain.
X To activate: press button : until the
å warning lamp goes out in the
instrument cluster. EBD (electronic brake force
distribution)
i Observe the "Important safety notes"
section ( Y page 53).
EBD monitors and controls the brake
pressure on the rear wheels to improve
driving stability while braking. G
WARNING
If the EBD malfunctions, the brake system will
still function with full brake boost. However,
the rear wheels could lock up during
emergency braking situations, for example.
You could lose control of the vehicle and
cause an accident.
Adapt your driving style to the changed
driving characteristics. Theft deterrent locking systems
Immobilizer
The immobilizer prevents your vehicle from
being started without the correct key.
When leaving the vehicle, always take the
SmartKey with you and lock the vehicle. The
engine can be started by anyone with a valid
SmartKey that is left inside the vehicle.
X To activate: remove the SmartKey from
the ignition lock.
X To deactivate: switch on the ignition.
i The immobilizer is always deactivated
when you start the engine.
In the event that the engine cannot be
started when the starter battery is fully
charged, the immobilizer may be faulty. Contact an authorized Mercedes-Benz
Center or call 1-800-FOR-MERCedes (in
USA) or 1-800-387-0100
(in Canada). ATA (Anti-Theft Alarm system)
A visual and audible alarm is triggered if the
alarm system is armed and you open:
R a door
R a door using the mechanical key
R the rear door
R the hood
The alarm is also triggered if:
R the position of the vehicle is changed.
R a window is smashed.
The alarm is not switched off, even if you
close the open door that has triggered it, for
example.
i If the alarm stays on for more than 30
seconds, the emergency call system
mbrace (USA only) or TELEAID (Canada
only) initiates a call to the Customer
Assistance Center automatically. The
emergency call system initiates the call
provided that:
R you have subscribed to the mbrace/
TELEAID service.
R the mbrace/TELEAID service has been
activated properly.
R the required
mobile phone, power supply
and GPS are available. Theft deterrent locking systems
57
Safety Z
Page 103 of 284
!
To avoid damaging the wiper blades,
make sure that you touch only the wiper
arm of the wiper.
! Never open
the hood if a windshield wiper
arm has been folded away from the
windshield.
Never fold a windshield wiper arm without
a wiper blade back onto the windshield/
rear window.
Hold the windshield wiper arm firmly when
you change the wiper blade. If you release
the windshield wiper arm without a wiper
blade and it falls onto the windshield, the
windshield may be damaged by the force of
the impact.
Mercedes-Benz recommends that you have
the wiper blades changed at a qualified
specialist workshop.
Removing the wiper blade X
Remove the SmartKey from the ignition
lock.
X Fold the windshield wiper arm away from
the windshield until it engages.
X Position the wiper blade at right angles. X
Press locking spring :.
X Slide wiper blade = with hinge piece ?
from windshield wiper arm ;.Installing the wiper blade
:
Locking spring
; Windshield wiper arm
= Wiper blade
? Hinge piece
X Slide new wiper blade = with the recess
onto windshield wiper arm ;.
X Engage locking spring : into the end of
the wiper arm.
X Make sure that wiper blade = is seated
correctly.
X Fold windshield wiper arm ; back
onto the
windshield. Problems with the windshield wipers
The windshield wipers are obstructed Leaves or snow, for example, may be
obstructing the windshield wiper movement.
The wiper motor has been deactivated.
X
For safety reasons, you should remove the
SmartKey from the ignition lock.
X Remove the cause of the obstruction.
X Switch the windshield wipers back on.
The windshield wipers are inoperative The windshield wiper drive is malfunctioning.
X
Select another wiper speed on the
combination switch.
X Have the windshield wipers checked at a
qualified specialist workshop. Windshield wipers
101
Lights and windshield wipers Z
Page 113 of 284
adjustment to direct the air to air vents in the
vehicle interior that are not in the immediate
area of unprotected skin.
In order to ensure the direct flow of fresh air
through the
air vents into the vehicle interior,
please observe the following notes:
R keep the air intake grille on the hood free
of blockages, such as ice, snow or leaves
R never cover the air vents or air intake grille
in the vehicle interior.
i For virtually draft-free ventilation, adjust
the sliders of the air vents to the center
position. Setting the center air vents
Center air vents
:
Center air vent, left
; Center air vent, right
= Center vent thumbwheel, right
? Center vent thumbwheel, left
X To open/close: turn thumbwheels
=
and ? to the right or left. Setting the side air vents
Side air vents
:
Side air vent
; Swiveling side air vent
= Control for side air vent
X To open/close:
turn thumbwheel
=
to the
left or right. Setting the rear-compartment air
vents
X
To
open/close:
turn thumbwheel :
up or
down.
X To set the air direction: move slider ;
for the corresponding rear-compartment
air vent to the left, right, up or down. Setting the air vents
111
Climate control Z
Page 173 of 284
Display messages Possible causes/consequences and
M Solutions?
Coolant
Stop,
Turn
Engine Off The coolant is too hot.
X
Pull over and stop the vehicle safely and switch off the engine,
paying attention to road and traffic conditions.
X Make sure that the air supply to the radiator is not blocked, e.g.
by snow, slush or ice.
X Wait until the display message disappears before restarting the
engine. Otherwise, there is a risk of engine damage.
X Pay attention to the coolant temperature display.
X If the temperature increases again, visit a qualified specialist
workshop immediately. The poly-V-belt may have torn.
X
Pull over and stop the vehicle safely and switch off the engine,
paying attention to road and traffic conditions.
X Open the hood.
X Check whether the poly-V-belt is torn.
If the poly-V-belt is torn:
! Do not
continue driving. The engine could otherwise overheat.
X Consult a qualified specialist workshop.
If the poly-V-belt is not damaged:
X Wait until the display message disappears before restarting the
engine. Otherwise, there is a risk of engine damage.
X Pay attention to the coolant temperature display.
X Visit a qualified specialist workshop. G
WARNING
Driving when your engine is overheated can cause some fluids which may have leaked into the
engine compartment to catch fire. You could be seriously burned.
Steam from
an overheated engine can cause serious burns which can occur just by opening the
engine hood. Stay away from the engine if you see or hear steam coming from it.
Stop the vehicle in a safe location away from other traffic. Turn off the engine, get out of the
vehicle and do not stand near the vehicle until the engine has cooled down.
! If the coolant temperature exceeds 248 ‡(120 †) do not continue driving. The engine will
otherwise be damaged. Display messages
171
On-board computer and displays Z
Page 174 of 284
Display messages Possible causes/consequences and
M Solutions? The engine fan is defective.
X
At coolant temperatures under 248 ‡ (120 † ), drive to the next
qualified specialist workshop.
X Avoid subjecting the engine to heavy loads, e.g. driving in
mountainous terrain, and stop-and-go traffic. # The battery is not being charged.
Possible causes are:
R
a defective alternator
R a torn poly-V-belt
R a malfunction in the electronics
X Pull over and stop the vehicle safely and switch off the engine,
paying attention to road and traffic conditions.
X Open the hood.
X Check whether the poly-V-belt is torn.
If the poly-V-belt is torn:
! Do not
continue driving. The engine could otherwise overheat.
X Consult a qualified specialist workshop.
If the poly-V-belt is not damaged:
X Visit a qualified specialist workshop. The battery voltage is too low.
X
Switch off electrical consumers that are not required.
X Have the battery and alternator checked at a qualified specialist
workshop. The battery has been charged or the vehicle has been jump-
started.
X
Have the battery and alternator checked at a qualified specialist
workshop. 4
Check
oil
level at
next gas station. The engine oil level has dropped to a critical level.
X
Check the oil level (Y page 211).
X If necessary, add engine oil ( Y page 213).
X Have the engine checked for leaks if the engine oil needs to be
refilled more often than usual. You have added too much engine oil. There is a risk of damaging
the engine or catalytic converter.
X
Siphon off excess engine oil until it is at the specified level.
Observe the legal requirements.172
Display messages
On-board computer and displays
Page 179 of 284
Display messages Possible causes/consequences and
M Solutionsh
Tire
Pres.
Caution
Tire Defect G
Risk of accident
The tire pressure in one or more tires has dropped suddenly.
X Stop the vehicle without making any sudden steering or braking
maneuvers. Pay
attention to the traffic conditions as you do so.
X If necessary, change a wheel ( Y page 226).h
Tire Pres. Check
Tires G
Risk of accident
The tire pressure in one or more tires has dropped significantly.
X Stop the vehicle without making any sudden steering or braking
maneuvers. Pay
attention to the traffic conditions as you do so.
X If necessary, change a wheel ( Y page 226).
X Check the tire pressure. If necessary, correct the tire pressure
(Y page 248). Vehicle
Display messages Possible causes/consequences and
M Solutions: The rear door is open.
X
Close the rear door. M G
Risk of accident
Vehicles with anti-theft alarm system:
The hood is open. A warning tone also sounds.
X Pull over and stop the vehicle safely as soon as possible, paying
attention to road and traffic conditions.
X Apply the parking brake.
X Close the hood. ¡ At least one door is open.
X
Close all the doors. ~
Bluetooth Ready The Bluetooth
®
connection between your mobile phone and
COMAND is not activated.
X If desired, activate the Bluetooth ®
connection between your
mobile phone and COMAND (see the separate Operator's
Manual). ¥
Top
Up
Washer Fluid The washer fluid level in the washer fluid reservoir has dropped
below the minimum.
X
Add washer fluid ( Y page 214). Display messages
177
On-board computer and displays Z
Page 208 of 284
If indicator lamp : goes out after
approximately 20 seconds and has not
flashed rapidly:
X
Release transmitter buttons ;, = or ?
on the integrated remote control and
transmitter button B on the garage door
remote control.
X Repeat the procedure for the other
transmitter buttons. When doing so, vary
the distance between the garage door's
remote control
and the transmitter buttons
in the rear-view mirror.
i If the garage door system works with a
rolling code, you must synchronize the
remote control integrated into the rear-
view mirror with the garage door system
receiver after programming.
You will find further information in the
garage door opening system's operating
instructions, e.g. the sections on
"Synchronizing the transmitter" or
"Registering a new transmitter". You can
also call the hotline mentioned above.
Notes on programming the remote
control
Canadian radio frequency laws require a
"break" (or interruption) of the transmission
signals a few seconds after broadcasting.
Therefore, these signals may not last long
enough for the integrated remote control to
recognize the signal during programming.
Comparable with Canadian law, some U.S.
garage door openers also have a built-in
"interruption".
If you live in Canada or have difficulties
programming the garage door opener
(regardless of
where you live) when using the
programming steps (see above), proceed as
follows:
X Press transmitter button ( ;, = or ?
) and
hold it down during the following steps until the setup has been completed
successfully.
X At the same time, press transmitter button
B of the garage door remote control for
two seconds, then release it for two
seconds, then press it again for two
seconds.
X Repeat this sequence on transmitter
button B of the garage door remote
control until
the frequency signal has been
saved.
X If the setup procedure is successful,
indicator lamp : flashes once slowly and
goes out after a few seconds.
X Continue with the other programming
steps (see above).
Problems when programming
If you have problems when programming the
integrated remote control, please note the
following:
R check the transmitter frequency of garage
door remote control A (which can usually
be found
on the rear of the remote control).
The integrated remote control is
compatible with devices that operate at
frequencies between 280 and 390 MHz.
R replace the batteries in garage door remote
control A. This increases the likelihood of
garage door remote control A sending a
strong and precise signal to the integrated
remote control on the rear-view mirror.
R when programming, hold garage door
remote control A at varying distances and
angles from the transmitter button which
you are programming. Try different angles
at a distance between 2 and 12 inches (5
to 30 cm) or the same angle at varying
distances.
R if there is another garage door remote
control for the same device, perform the
programming steps again using that garage
door opener. Before performing these
steps, make sure that there are new206
Features
Stowing and features
Page 212 of 284
Useful information
i This Operator's Manual describes all
models and all standard and optional
equipment of your vehicle available at the
time of publication of the Operator's
Manual. Country-specific differences are
possible. Please
note that your vehicle may
not be equipped with all features
described. This also applies to safety-
related systems and functions.
i Please read the information on qualified
specialist workshops (Y page 20). Engine compartment
Hood
Opening the hood G
WARNING
Do
not pull the release lever while the vehicle
is in motion. Otherwise, the hood could be
forced open by passing air flow.
This could
cause the hood to come loose and
injure you and/or others. G
WARNING
Do not open the hood when the engine is
overheated. You could be seriously injured.
Observe the coolant temperature gauge to
determine whether the engine may be
overheated. If you see flames or smoke
coming from the engine compartment, move
away from the vehicle. Wait until the engine
has cooled. If necessary, call the fire
department. G
WARNING
You
could be injured when the hood is open –
even when the engine is turned off.
Parts of the engine can become very hot. To
prevent burns,
let the engine cool completely
before touching any components on the
vehicle. Comply with all relevant safety
precautions. G
WARNING
To help prevent personal injury, stay clear of
moving parts when the hood is open and the
engine is running.
The radiator fan may continue to run for
approximately 30 seconds or may even
restart after the engine has been turned off.
Stay clear of fan blades. G
WARNING
The engine is equipped with a transistorized
ignition system. Because of the high voltage,
it is dangerous to touch any components
(ignition coils, spark plug sockets, diagnostic
socket) of the ignition system:
R with the engine running
R while starting the engine
R when the ignition is switched on and the
engine is turned manually
X Make sure that the windshield wipers are
switched off. G
WARNING
The windshield wipers and wiper linkage
could be set in motion.
When the hood is open, you or others could
be injured by the wiper linkage.
Make sure that the windshield wipers are
switched off
and that the SmartKey has been
pulled out of the ignition lock before opening
the hood.
The release lever on the hood is in the footwell
on the left-hand side of the vehicle when
viewed in the direction of travel. 210
Engine compartment
Maintenance and care