lights MERCEDES-BENZ G-Class 2013 W463 Comand Manual

Your COMAND equipment
These operating instructions describe all the
standard and optional equipment for your
COMAND system, as available at the time of
going to print. Country-specific differences
are possible. Please note that your COMAND
system may not be equipped with all the
features described. Introduction
Important safety notes
G
WARNING
For safety reasons, only enter a new
destination when the vehicle is stationary.
When you are driving, another passenger
should enter the destination. Read the
Operator's Manual and select the route
before driving.
Bear in mind that at a speed of only 30 mph
(approximately 50 km/h), the vehicle covers
a distance of 44 feet (approximately 14 m) per
second.
COMAND calculates the route to the
destination without taking account of the
following, for example:
R traffic lights
R stop and give way signs
R merging lanes
R parking or stopping in a no parking/no
stopping zone
R other road and traffic rules and regulations
R narrow bridges G
WARNING
COMAND may give incorrect navigation
commands if the actual road/traffic situation
no longer corresponds to the data on the
digital map. Digital maps do not cover all
areas nor all routes in an area. For example,
a route may have been diverted or the
direction of a one-way street may have
changed. For this reason, you must always observe road
and traffic rules and regulations during your
journey. Road and traffic rules and regulations
always have priority over the system's driving
recommendations. G
WARNING
Navigation announcements are intended to
direct you while driving without diverting your
attention from the road and driving.
Please always use this feature instead of
consulting the map display for directions.
Looking at the icons or map display can
distract you from traffic conditions and
driving, and increase the risk of an accident. General notes
Operational readiness of the navigation
system The navigation system must determine the
position of the vehicle before first use or
whenever operational status is restored.
Therefore, you may have to drive for a while
before precise route guidance is possible.
GPS reception Correct functioning of the navigation system
depends, amongst other things, on GPS
reception. In certain situations, GPS
reception may be impaired, there may be
interference or there may be no reception at
all, e.g. in tunnels or parking garages.
i
Using roof carriers may impair the correct
functioning of a roof antenna (phone,
satellite radio, GPS).
Entry restriction On vehicles for certain countries, there is a
restriction on entering data.
The restriction is active from a vehicle speed
of above approximately 3 mph (5 km/h). As
soon as the speed falls below approximately 54
Int
roductionNavigation

X
Select Yes
Yes when the prompt for starting the
navigation system is shown. The window
for starting the navigation system appears
(Y page 62).
X Select Start
Start .
or
X Select No Noto store the downloaded
destination in the destination memory for
later use.
i The destination addresses are
downloaded in the same order as they are
sent.
If you own several Mercedes-Benz vehicles
equipped with an mbrace subscriber
account: each destination address can be
downloaded by each vehicle associated
with the e-mail address registered for your
mbrace account. Route guidance
Important safety notes
G
WARNING
COMAND calculates the route to the
destination without taking account of the
following, for example:
R traffic lights
R stop and give way signs
R merging lanes
R parking or stopping in a no parking/no
stopping zone
R other road and traffic rules and regulations
R narrow bridges
COMAND can give incorrect navigation
commands if the actual street/traffic
situation does not correspond with the digital
map's data. For example, a route may have
been diverted or the direction of a one-way
street may have changed.
For this reason, you must always observe road
and traffic rules and regulations during your
journey. Road and traffic rules and regulations
always have priority over the system's driving
recommendations. Route guidance begins once a route has been
calculated (Y
page 62).
COMAND guides you to your destination by
means of navigation announcements in the
form of audible navigation announcements
and route guidance displays.
The route guidance displays can only be seen
if the display is switched to navigation mode.
If you do not follow the navigation
announcements or if you leave the calculated
route, COMAND automatically calculates a
new route to the destination.
If the digital map contains the corresponding
information, the following applies:
R when selecting a route, COMAND tries to
avoid roads that only have limited access,
e.g. roads closed to through traffic.
R roads that have time restrictions (e.g.
closed on Sundays and public holidays) are
considered for route guidance on days
when they are open. For this purpose, the
relevant times must be correctly stored in
the database. Displays during route guidance
Change of direction Changes of direction have three phases:
R
Preparation phase
R Announcement phase
R Change-of-direction phase Route guidance
81Navigation Z

X
To scroll through the display or select
phone numbers in a text message: turn
0082005B0083 the COMAND controller.
The display scrolls up or down line by line,
or skips to the next or previous telephone
number and automatically highlights it.
X To return to the list: press00A1and select
Back
Back.
Text message read-aloud function Settings for the read-aloud function:
R Language (Y page 40)
R Speed (Y page 39)
X Press 00A1while a text message is being
displayed, select Read Aloud
Read Aloud and press
00A1 to confirm.
COMAND reads out the text message.
X To cancel the read-aloud function: press
the 006C button.
or
X Press 00A1, select Cancel Read-Aloud
Cancel Read-Aloud
Function Function and press00A1to confirm.
Sender or text display You can switch between displaying the text
message sender or the text message content.
The sender display shows the sender of the
text message. If the sender is stored in the
COMAND phone book, the name is displayed.
The text display shows the first few words of
the text message.
X Select a text message in the text message
inbox by turning 0082005B0083the COMAND
controller.
X To switch to the text display: select the
list symbol to the right of the text message
by sliding 005B009Fthe COMAND controller and
press 00A1to confirm.
X Select Display Text
Display Text and press00A1to
confirm.
The view changes. X
To switch to the sender display: select
the list symbol to the right of the text
message by sliding 005B009Fthe COMAND
controller and press 00A1to confirm.
X Select Display Sender
Display Sender and press00A1to
confirm.
The view changes.
X To return to the telephone basic menu:
press the 003Dbutton.
Displaying details and phone numbers COMAND can also show a shortened sender
display in full.
X
Select a text message in the text message
inbox by turning 0082005B0083the COMAND
controller.
X Select the list symbol to the right of the text
message by sliding 005B009Fthe COMAND
controller and press 00A1to confirm.
X Select Details
Details and press 00A1to confirm.
The detailed view appears.
X To close the detailed view: slide009E005B009F the
COMAND controller.
X To return to the telephone basic menu:
press the 003Dbutton. Managing text messages
Calling a text message (SMS) sender X
Press 00A1the COMAND controller while the
text message is being displayed.
X Select Call Sender Call Sender and press00A1to
confirm.
The telephone makes the call to the sender. Text messages (SMS)
141Telephone Z

X
Call up the carousel view (Y page 171).
X In the carousel view, bring a favorite to the
front by turning 0082005B0083or sliding 009E005B009Fthe
COMAND controller and press 00A1to
confirm.
The website is called up. Navigating the website
Overview Action Result
X
Turn 0082005B0083 the
controller. Navigates from one
item that can be
selected (e.g. link,
text field or
selection list) to the
next and highlights
the respective
element on the
website.
Sliding the
controller:
X
Left or right 009E005B009F
X Up or down 00A0005B0064
X Diagonally 009A005B0081 Moves the pointer
on the page.
X
Press 00A1the
controller. Calls up the menu or
opens the selected
item.
X
Press 0041. Calls up the
previous page.
X
Press 003C. Closes the Internet
browser. If several
windows are open,
the current window
is closed.
Example: highlighting an item that can
be selected Internet
173Online and Internet functions

X
Select a genre, e.g. pop, and press 00A1to
confirm.
The track list is displayed.
X Select a track and press 00A1to confirm.
Playback starts.
Selecting composers X
Select Composers Composers in the category list by
turning 0082005B0083the COMAND controller and
press 00A1to confirm.
The available composers are displayed
alphabetically.
Selecting music genres X
Select Genres
Genres in the category list by
turning 0082005B0083the COMAND controller and
press 00A1to confirm.
The available music genres are displayed
alphabetically.
Selecting a cover X
Select Select By Cover
Select By Cover in the category
list (Y page 204) by turning 0082005B0083the
COMAND controller and press 00A1to
confirm.
The available covers are displayed in
alphabetical order of the artists. X
Select the desired cover by turning 0082005B0083
the COMAND controller and press 00A1to
confirm.
The corresponding album is played. Selecting via keyword search X
Select Keyword Keyword Search
Searchin the category list
by turning 0082005B0083the COMAND controller
and press 00A1to confirm.
An input menu appears. X
To change the character set used in the
character bar: highlightSelect Selectby sliding
005B0064 and turning 0082005B0083the COMAND
controller and press 00A1to confirm.
A list of available character sets is shown.
X Select the desired character set and press
00A1 to confirm.
X Enter characters and confirm the entry.
Character entry (Y page 32).
Depending on the entry, the hits are shown
in a list. X
Select an entry by turning 0082005B0083the
COMAND controller and press 00A1to
confirm. 206
Music searchAudio