remote start MERCEDES-BENZ G500 2005 W463 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2005, Model line: G500, Model: MERCEDES-BENZ G500 2005 W463Pages: 416, PDF Size: 4.44 MB
Page 34 of 416
34 Getting startedThe “Getting started” section provides an
overview of the vehicle’s most basic func-
tions. First-time Mercedes-Benz owners
should pay special attention to the infor-
mation given here.
If you are already familiar with the basic
functions described here, the “Controls in
detail” section will help you with further in-
formation. The corresponding page refer-
ences are at the end of each segment.Unlocking
Unlocking with the SmartKeySmartKey with remote control1‹Lock button
2ŒUnlock button
3ÂPanic button (
page 79)
Press unlock button Œ on the
SmartKey.
All turn signal lamps flash once. The
locking knobs in the doors move up.
The anti-theft alarm system is dis-
armed.
Get in the vehicle and insert the
SmartKey in the starter switch.
For more information, see “Locking and
unlocking” (
page 92).
Page 92 of 416
92 Controls in detailIn the “Controls in detail” section you will
find detailed information on how to oper-
ate the equipment installed in your vehicle.
If you are already familiar with the basic
functions of your vehicle, this section will
be of particular interest to you.
To quickly familiarize yourself with the ba-
sic functions of the vehicle, refer to the
“Getting started” section of this manual.
The corresponding page numbers are giv-
en at the beginning of each segment.Locking and unlocking
SmartKey
Your vehicle comes supplied with two
SmartKeys, each with remote control and
a removable mechanical key. The locking
tabs for the mechanical key portion of the
two SmartKeys are a different color to help
distinguish each key unit.
The SmartKey provides an extended oper-
ating range. To prevent theft, however, it is
advisable to only unlock the vehicle when
you are in close proximity to it.
The SmartKey centrally locks and unlocks:
the doors
the tailgate
the fuel filler flap
SmartKey with remote control1‹ Lock button
2Locking tab for mechanical key
3Œ Unlock button
4Battery check lamp
5Â Panic button (
page 79)
iYou can also open and close the power
windows (
page 172) and tilt/sliding
sunroof (
page 175) using the
SmartKey.
Page 99 of 416
99 Controls in detail
Locking and unlocking
Locking and unlocking from the inside
You can lock or unlock the vehicle from in-
side using the central locking switches.
This can be useful, for example, if you want
to unlock the passenger door from the in-
side or want to lock the vehicle before
starting to drive.
The fuel filler flap cannot be locked or un-
locked with the central locking switch.The central locking switch is located in the
center console.
Central locking switch1Locking
2Unlocking
Locking
Press central locking switch1.
If all the doors and the tailgate are
closed, the vehicle locks.Unlocking
Press central locking switch2.
The vehicle unlocks.
Warning!
G
When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. Unsuper-
vised use of vehicle equipment may cause
an accident and/or serious personal injury.
iYou can open a locked door from the
inside. Open door only when conditions
are safe to do so.
If the vehicle was previously centrally
locked using the SmartKey, it will not
unlock using the central locking switch.
If the vehicle was previously locked
with the central locking switch
while in the selective remote con-
trol mode, only the door opened
from the inside is unlocked.
while in the global remote control
mode, the complete vehicle is un-
locked when a door is opened from
the inside.
Page 208 of 416
208 Controls in detailUseful featuresProgramming or reprogramming the in-
tegrated remote control
Step 1:
Switch on the ignition (
page 35).
Step 2:
If you have previously programmed an
integrated signal transmitter button
and wish to retain its programming,
proceed to step 3. Otherwise, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when the indicator lamp1
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory. If you later wish to program a
second and/or third hand-held trans-
mitter to the remaining two signal
transmitter buttons, do not repeat this
step and begin directly with step 3.Step 3:
Hold the end of the hand-held remote
control transmitter6 of the device
you wish to train approximately 2 to
5 in (5 to12 cm) away from the surface
of the integrated remote control locat-
ed on the interior rear view mirror,
keeping the indicator lamp1 in view.
Step 4:
Using both hands, simultaneously
press the hand-held transmitter
button5 and the desired integrated
signal transmitter button (2, 3
or4). Do not release the buttons until
completing step 5.
The indicator lamp1 on the integrat-
ed remote control will flash, first slowly
and then rapidly.Step 5:
When the indicator lamp1 flashes
rapidly, release both buttons.
Step 6:
Press and hold the just-trained inte-
grated signal transmitter button and
observe the indicator lamp1.
If the indicator lamp1 stays on con-
stantly, programming is complete and
your device should activate when the
integrated signal transmitter button is
pressed and released.iThe indicator lamp1 flashes the first
time the signal transmitter button is
programmed. If this button has already
been programmed, the indicator lamp
will only start flashing after 20 sec-
onds.
Page 210 of 416
210 Controls in detailUseful featuresIf you live in Canada or if you are having dif-
ficulties programming a gate operator (re-
gardless of where you live) by using the
programming procedures, replace step 4
with the following:
Step 4:
Continue to press and hold the inte-
grated signal transmitter button (2,
3 or4) while you press and re-press
(“cycle”) your hand-held remote con-
trol transmitter6 every two seconds
until the frequency signal has bee-
learned. Upon successful training, the
indicator lamp1 will flash slowly and
then rapidly after several seconds.
Proceed with programming step 5 and
step 6 to complete. Operation of integrated remote control
Switch on the ignition (
page 35).
Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing the integrated remote control
memory
Switch on the ignition (
page 35).
Simultaneously hold down the signal
transmitter buttons2 and 4, for ap-
proximately 20 seconds, until the indi-
cator lamp1 blinks rapidly. Do not
hold for longer than 30 seconds.
The codes of all three channels are
erased.Reprogramming a single integrated sig-
nal transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:
Press and hold the desired signal trans-
mitter button (2, 3 or4). Do not re-
lease the button.
The indicator lamp will begin to flash af-
ter 20 seconds. Without releasing the
integrated signal transmitter button,
proceed with programming starting
with step 3.iIf you sell your vehicle, erase the codes
of all three channels.
Page 393 of 416
393 Index
Driving
General instructions 43, 216
In winter 221
Problems 55
Safety systems 80
Through standing water 222
Driving abroad 232
Driving and safety systems
4-ETS 83
ABS 80
BAS 82
EBB 84
ESP 84
Driving instructions 216
Passenger compartment 223
Driving off 218
Driving systems 176
Cruise control 176
Driving safety systems 80
Driving through water 227E
Easy-entry/exit feature 100
Activating 142
EBB 80, 84
Electrical fuses 360
Electrical outlet 196
Electrical system
Technical data 372
Electronic Brake Booster (EBB) 84
Electronic Stability Program see ESP
Electronic Traction System (ETS) 83
Emergency call system 198
Emergency calls
Initiating an emergency call 201
With Tele Aid 199
Emergency operation (Limp Home
Mode) 153
Emergency operations
Closing tilt/sliding sunroof 328
Locking the vehicle 326
Opening tilt/sliding sunroof 328
Remote door unlock 205
Unlocking the tailgate 325
Unlocking the vehicle 325
Emergency tensioning device see ETD
Emission control 233Emission control information label 366
Ending
A call (telephone) 146
Engine
Compartment 238
Message in display 292
Starting with SmartKey 49
Technical data 368
Turning off with SmartKey 58
Engine air filter
Messages in display 308
Engine cleaning 282
Engine compartment 238
Hood 238
Engine malfunction indicator
lamp 25, 292
Engine number 382
Engine oil 239, 375
Adding 243
Additives 376
Checking level 239
Consumption 239
Display messages 310
Messages in display 241, 309
Oil dipstick 243
Viscosity 382
Page 397 of 416
397 Index
Instrument cluster 24, 120, 383
Cleaning 284
Coolant temperature display 120
Illumination 120
Lamps in 294
Multifunction display 123
Outside temperature indicator 122
Selecting language 136
Instrument lighting 120
Instruments and controls see Cockpit
Interior lighting 116
Delayed shut-off 140
Manual operation 117
Interior rear view mirror
Adjusting 41
Intermittent wiping 54
Interval wiping 55
Switching off 55
Switching on 55J
Jack 322
Jump starting 354K
Key, mechanical 325
Key, SmartKey
Battery check lamp 94
Checking the batteries 95
Factory setting 94
Global locking 94
Global unlocking 94
Loss of 96
Positions in starter switch 35
Remote controls 92
Restoring to factory setting 95
Selective setting 94
Starting the engine 49
Unlocking with 34
Key-dependency memory
Settings 143
Keys 92
Kickdown 153, 383
Kilometers/miles in speedometer 136
Kilopascal 272
Km/h or mph in speedometer 136