bulb MERCEDES-BENZ G500 2007 W463 User Guide

377 Practical hints
Replacing bulbs
Replacing bulbs
Bulbs
Safe vehicle operation depends on proper
exterior lighting and signaling. It is there-
fore essential that all bulbs and lamp
assemblies are in good working order at all
times.
Correct headlamp adjustment is extremely
important. Have headlamps checked and
readjusted at regular intervals and when a
bulb has been replaced. See an authorized
Mercedes-Benz Light Truck Center for
headlamp adjustment.iIf the headlamps or front fog lamps are
fogged up on the inside as a result of high
humidity, driving the vehicle a distance with the
lights on should clear up the fogging.iSubstitute bulbs will be brought into use
when the following lamps malfunction:

Turn signal lamps

Tail lamps

Parking lamps

Rear fog lamp
Read and observe the messages in the
multifunction display (
page 354).

378 Practical hints
Replacing bulbs
Front lamps Rear lamps
LampType
1Additional turn signal
lampLED
2Locator lighting lampW6W
3Turn signal lamp1156 NA
4Side marker lampT4W
5Bi-Xenon headlamp:
Low and high beam1
1Bi-Xenon headlamp: Low beam and high beam use
the same D1S-35 W lamp. Do not replace the
Bi-Xenon bulbs yourself. Contact an authorized
Mercedes-Benz Light Truck Center.
D1S-35 W
Parking and standing
lampW5W
Blue vision
6Front fog lampH11 (55 W)
LampType
7High mounted brake
lampLED
8Turn signal lampPY 21 W
Brake and tail lampP21/5W
Tail, parking and
standing lampW5W
9Backup lampP21W
aLicense plate lampsC5W
bRear fog lampP21W
cSide marker lampT4W

379 Practical hints
Replacing bulbs
Notes on bulb replacement

Only use 12-volt bulbs of the same type
and with the specified watt rating.

Switch lights off before changing a bulb
to prevent short circuits.

Always use a clean lint-free cloth when
handling bulbs.

Your hands should be dry and free of oil
and grease.

If the newly installed bulb does not
come on, contact an authorized
Mercedes-Benz Light Truck Center.Have the LEDs and bulbs for the following
lamps replaced at an authorized
Mercedes-Benz Light Truck Center:

the additional turn signal lamps in the
exterior rear view mirrors

the high mounted brake lamp

the Bi-Xenon lamps

the locator lighting lamps in the
exterior rear view mirrors
Warning!G
Bulbs and bulb sockets can be very hot.
Allow the lamp to cool down before
changing a bulb.
Keep bulbs out of reach of children.
Halogen lamps contain pressurized gas.
A bulb can explode if you:

touch or move it when hot

drop the bulb

scratch the bulb
Wear eye and hand protection.
Because of high voltage in Xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.
!Do not replace the LEDs yourself. You could
otherwise damage the LEDs or parts of the vehi-
cle. Only have the LEDs replaced at an autho-
rized Mercedes-Benz Light Truck Center.

380 Practical hints
Replacing bulbs
Replacing bulbs for front lamps
Before you start to replace a bulb for a
front lamp, do the following first:
Turn the exterior lamp switch to
positionM (
page 117).Bi-Xenon headlamp Parking and standing lamp bulbLeft headlamp shown, right headlamp
laterally reversed
1Securing screw (trim panel)
2Headlamp trim panel
Loosen and remove securing
screws1.
Remove headlamp trim panel2 in
direction of arrow and the seal.
iG 55 AMG (U.S. vehicles only):
Fold the brush guard down before replacing
bulbs (
page 375).
G55AMG:
Remove the protective grille before replacing the
bulbs.
Warning!G
Do not remove the low beam/high beam
cover for the Bi-Xenon headlamp. Because
of high voltage in Xenon lamps, it is danger-
ous to replace the bulb or repair the lamp
and its components. We recommend that
you have such work done by a qualified
technician.

381 Practical hints
Replacing bulbs
Left headlamp shown, right headlamp
laterally reversed
3Securing screw (headlamp)
4Adjusting screw (headlamp)
5Headlamp
Loosen and remove headlamp-securing
screws3.
Remove headlamp5.5Headlamp
6Bulb socket
Hold headlamp5, push gently onto
bulb socket6, and turn bulb
socket6 counterclockwise to its
stop.
Pull bulb socket6 out of
headlamp5.7Bulb
Pull bulb7 out of its bulb socket.
Insert the new bulb into the bulb
socket.
Hold headlamp5, insert bulb
socket6 into headlamp5, and turn
bulb socket6 clockwise to its stop.
Insert headlamp5 and install and
tighten headlamp-securing screws3.
Install headlamp trim panel2 and the
seal.
Install and tighten securing screws1.
iDo not turn adjusting screw4. If adjusting
screw4 is turned, the headlamp adjustment
must be checked at a Mercedes-Benz Light
Truck Center.

382 Practical hints
Replacing bulbs
Front fog lamp bulb
Right front fog lamp shown, left front fog
lamp laterally reversed
1Securing screw (trim panel)
2Front fog lamp trim panel
Loosen and remove securing
screws1.
Remove front fog lamp trim panel2 in
direction of arrow and the seal.
Right front fog lamp shown, left front fog
lamp laterally reversed
3Securing screw (front fog lamp)
4Adjusting screw (front fog lamp)
5Front fog lamp
Loosen and remove front fog
lamp-securing screws3.
Remove front fog lamp5.5Front fog lamp
6Bulb socket
Hold front fog lamp5, push gently
onto bulb socket6, and turn bulb
socket6 counterclockwise to its
stop.
Pull bulb socket6 out of front fog
lamp5.
iDo not turn adjusting screw4. If adjusting
screw4 is turned, the front fog lamp adjust-
ment must be checked at a Mercedes-Benz Light
Truck Center.

383 Practical hints
Replacing bulbs
7Bulb
Pull bulb7 out of its bulb socket.
Insert the new bulb into the bulb
socket.
Hold front fog lamp5, insert bulb
socket6 into front fog lamp5, and
turn bulb socket6 clockwise to its
stop.
Insert front fog lamp5 and install and
tighten front fog lamp-securing
screws3.
Install front fog lamp trim panel2 and
the seal.
Install and tighten securing screws1.Front turn signal lamp bulb
1Securing screw
2Turn signal lens
Loosen and remove securing
screws1.
Remove turn signal lens2.3Bulb
Press bulb3 gently into the socket,
turn counterclockwise and remove it.
Press the new bulb gently into the
socket and turn clockwise until it
engages.
Reinstall turn signal lens2.
Install and tighten securing screws1.
iG55AMG:
Remove the protective grille before replacing the
bulbs.
iDo not overtighten securing screws1.
Otherwise turn signal lens2 could be damaged.

384 Practical hints
Replacing bulbs
Side marker lamp bulb
The following description applies to both,
the front and the rear side marker lamps.
Front side marker shown
1Securing screw
2Side marker lamp housing
Loosen and remove securing
screws1.
Remove side marker lamp housing2.2Side marker lamp housing
3Dust cover
Remove dust cover3.
Press catch aside and pull out the bulb
socket with the bulb from side marker
lamp housing2.4Bulb
Press gently onto bulb4 and turn
counterclockwise out of its bulb
socket.
Press the new bulb gently into the bulb
socket and turn clockwise until it
engages.
Insert the bulb socket back into side
marker lamp housing2.
Reinstall dust cover3.

385 Practical hints
Replacing bulbs
Reinstall side marker lamp housing2.
Install and tighten securing screws1.
Additional turn signal lamps
The additional turn signal lamps in the
exterior rear view mirrors have LEDs.
If a malfunction occurs or LEDs fail to
function, the entire turn signal unit must be
replaced. Have the turn signal unit
replaced at an authorized Mercedes-Benz
Light Truck Center.Locator lighting lamps
The locator lighting lamps in the exterior
rear view mirrors have bulbs.
Have the bulbs replaced at an authorized
Mercedes-Benz Light Truck Center.
Replacing bulbs for rear lamps
Before you start to replace a bulb for a rear
lamp, do the following first:
Turn the exterior lamp switch to
positionM (
page 117).Bulbs in tail lamp unit
Left tail lamp lens shown, right tail lamp
lens laterally reversed
1Securing screw
2Tail lamp lens
Loosen and remove securing
screws1.
Remove tail lamp lens2.
iDo not overtighten securing screws1.
Otherwise side marker lamp housing2 could
be damaged.
iG55AMG:
Remove the protective grille before replacing the
bulbs.


386 Practical hints
Replacing bulbs
Left tail lamp unit shown, right tail lamp
unit laterally reversed
3Turn signal lamp bulb
4Brake, tail, parking and standing lamp
bulb
5Tail, parking and standing lamp bulb
Press gently onto respective
bulb3,4, or5 and turn counter-
clockwise out of its bulb socket.
Press the new bulb gently into the bulb
socket and turn clockwise until it
engages.
Reinstall tail lamp lens2.
Install and tighten securing screws1.Rear fog lamp bulb/Backup lamp bulb
The following description applies to both,
the rear fog lamp and the backup lamp.
Rear fog lamp shown
1Securing screw
2Lamp lens
Loosen and remove securing
screws1.
Remove lamp lens2.3Bulb
Press gently onto bulb3 and turn
counterclockwise out of its bulb
socket.
Press the new bulb gently into the bulb
socket and turn clockwise until it
engages.
Reinstall lamp lens2.
Install and tighten securing screws1.
iDo not overtighten securing screws1.
Otherwise tail lamp lens2 could be damaged.
iDo not overtighten securing screws1.
Otherwise lamp lens2 could be damaged.