instrument cluster MERCEDES-BENZ G500 2007 W463 Owner's Guide

99
Controls in detail
Locking and unlocking
Seats
Memory function
Lighting
Instrument cluster
Control system
Automatic transmission
Transfer case
Differential locks
Good visibility
Climate control
Power windows
Power tilt/sliding sunroof
Driving systems
Loading
Useful features

122 Controls in detail
Lighting
Combination switch
The combination switch is located on the
left of the steering column.
1High beam
2High beam flasherHigh beam
Canada only: Turn the exterior lamp
switch to positionB (
page 117).
or
USA only: Turn the exterior lamp switch
to positionB orU
(
page 117).
Push the combination switch in
direction of arrow1 to switch on the
high beam.
The high beam headlamp indicator
lampA in the instrument cluster
comes on (
page 26).
Pull the combination switch in direction
of arrow2 to its original position to
switch off the high beam.
The high beam headlamp indicator
lampA in the instrument cluster
goes out.
High beam flasher
Pull the combination switch briefly in
direction of arrow2.
Corner-illuminating front fog lamps
The corner-illuminating front fog lamps
improve illumination of the area in the
direction into which you are turning.
The corner-illuminating front fog lamps will
operate with the engine running and with

the exterior lamp switch in
positionB (
page 117)
or

the exterior lamp switch in
positionU (
page 117)
or

the daytime running lamp mode
activated (
page 119)
iThe corner-illuminating front fog lamps will
only come on in low ambient lighting conditions.
iIf you are driving faster than 25 mph
(40 km/h) or have the front fog lamps switched
on, the corner-illuminating function is not avail-
able.

130 Controls in detail
Instrument cluster
For a full view on the instrument cluster,
see “At a glance” (
page 26).
1Reset button
The instrument cluster is activated when
you

open a door

switch on the ignition (page 39)

press reset button1

switch on the exterior lamps
(
page 117)You can change the instrument cluster set-
tings in the instrument cluster submenu of
the control system (
page 149).Adjusting instrument cluster
illumination
Use reset button1 to adjust the illumina-
tion brightness for the instrument cluster.
To brighten illumination
Turn reset button1 clockwise until
the desired level of illumination is
reached.
To dim illumination
Turn reset button1 counterclockwise
until the desired level of illumination is
reached.
Warning!G
No messages will be displayed if either the
instrument cluster or the multifunction
display is inoperative.
As a result, you will not be able to see infor-
mation about your driving conditions, such
as speed or outside temperature, warn-
ing/indicator lamps, malfunction/warning
messages or the failure of any systems.
Driving characteristics may be impaired.
If you must continue to drive, do so with
added caution. Contact an authorized
Mercedes-Benz Light Truck Center as soon
as possible.
iThe instrument cluster illumination is
dimmed or brightened automatically to suit
ambient light conditions.
The instrument cluster illumination will also be
adjusted automatically when you switch on the
vehicle’s exterior lamps.

131 Controls in detail
Instrument cluster
Coolant temperature gauge
The coolant temperature gauge is on the
left side in the instrument cluster
(
page 26).
Resetting trip odometer
Make sure you are viewing the
standard display (
page 140).
If it is not displayed, press buttonè
orÿ on the multifunction steering
wheel (
page 134) repeatedly until
the standard display appears in the
multifunction display.
Press and hold reset button1
(
page 130) until the trip odometer is
reset.
Warning!G

Driving when your engine is overheated
can cause some fluids which may have
leaked into the engine compartment to
catch fire. You could be seriously
burned.

Steam from an overheated engine can
cause serious burns which can occur
just by opening the hood. Stay away
f r o m t h e e n g i n e i f y o u s e e o r h e a r s t e a m
coming from it.
Stop the vehicle in a safe location away from
other traffic. Turn off the engine, get out of
the vehicle and do not stand near the vehicle
until the engine has cooled down.
!Excessive coolant temperature triggers a
warning message in the multifunction display
(
page 348).
The engine should not be operated with the
coolant temperature above 248°F (120°C).
Doing so may cause serious engine damage
which is not covered by the Mercedes-Benz
Limited Warranty.
iDuring severe operating conditions, e.g.
stop-and-go traffic, the coolant temperature may
rise close to 248°F (120°C).

132 Controls in detail
Instrument cluster
Tachometer
The red marking on the tachometer
(
page 26) denotes excessive engine
speed.
To help protect the engine, the fuel supply
is interrupted if the engine is operated
within the red marking.
Outside temperature indicator
The outside temperature is displayed in
the multifunction display (
page 133).The temperature sensor is located in the
front bumper area. Due to its location, the
sensor can be affected by road or engine
heat during idling or slow driving. This
means that the accuracy of the displayed
temperature can only be verified by com-
parison to a thermometer placed next to
the sensor, not by comparison to external
displays (e.g. bank signs, etc.).
When moving the vehicle into colder ambi-
ent temperatures (e.g. when leaving your
garage), you will notice a delay before the
lower temperature is displayed.
A delay also occurs when ambient tem-
peratures rise. This prevents inaccurate
temperature indications caused by heat
radiated from the engine during idling or
slow driving.
!Avoid driving at excessive engine speeds, as
it may result in serious engine damage that is not
covered by the Mercedes-Benz Limited
Warranty.
Warning!G
The outside temperature indicator is not
designed to serve as an ice-warning device
and is therefore unsuitable for that purpose.
Indicated temperatures just above the freez-
ing point do not guarantee that the road sur-
face is free of ice. The road may still be icy,
especially in wooded areas or on bridges.

139 Controls in detail
Control system
Menus, submenus and functions
Menu5Menu6Menu7
SettingsTrip computerTEL
(page 146)(page 157)(page 159)
Commands/submenu
Resetting to factory settingsFuel consumption statistics
since startLoading phone book
Instrument cluster submenuFuel consumption statistics
since last resetSearching for name in phone
book
Lighting submenuResetting fuel consumption
statistics
Vehicle submenuDistance to empty
Convenience submenu
iThe headings used in the menus table are
designed to facilitate navigation within the
system and are not necessarily identical to those
shown in the control system displays.The first function displayed in each menu will
automatically show you which part of the system
you are in.

146 Controls in detail
Control system
Settings menu
In the
Settings menu there are two
functions:

The function Reset to factory
settings
, with which you can reset all
the settings to the original factory
settings.

A collection of submenus with which
you can make individual settings for
your vehicle.
Press buttonè orÿ repeatedly
until the
Settings menu appears in the
multifunction display.The following settings and submenus are
available in the
Settings menu:Resetting all settings
You can reset the functions of all
submenus to the factory settings.
Press the reset button in the
instrument cluster (
page 130) for
approximately 3 seconds.
The request to press the reset button
once more to confirm appears in the
multifunction display.
Press the reset button once more.
The functions of all submenus will reset
to factory settings.
FunctionPage
Resetting all settings146
Submenus in the settings menu147
Instrument cluster submenu149
Lighting submenu151
Vehicle submenu154
Convenience submenu156

148 Controls in detail
Control system
The table below shows what settings can
be changed within the various menus.
Detailed instructions on making individual
settings can be found on the following
pages.
Instrument clusterLightingVehicleConvenience
(page 149)(page 151)(page 154)(page 156)
Selecting speedometer
display modeSetting daytime
running lamp mode
(USA only)Selecting audio search
functionActivating
easy-entry/exit feature
Selecting languageSetting locator lightingSetting automatic
locking
Selecting display
(digital speedometer or
outside temperature)
for status indicatorSetting night security
illumination
Setting interior lighting
delayed shut-off

149 Controls in detail
Control system
Instrument cluster submenu
Access the
Inst. cluster submenu via
the
Settings menu. Use the Inst. clus-
ter
submenu to change the instrument
cluster display settings.
The following functions are available:Selecting speedometer display mode
Move the selection marker with
buttonæ orç to the
Inst.
cluster
submenu.
Press buttonj ork repeatedly
until the message
Disp.Unit
Speed-/odom.
appears in the multi-
function display.
The selection marker is on the current
setting.
Press buttonæ orç to set
speedometer unit to
km or miles.Selecting language
Move the selection marker with
buttonæ orç to the
Inst.
cluster
submenu.
Press buttonj ork repeatedly
until the message
Language appears in
the multifunction display.
The selection marker is on the current
setting.
FunctionPage
Selecting speedometer display
mode149
Selecting language149
Selecting display (digital speed-
ometer or outside temperature)
for status indicator150


158 Controls in detail
Control system
Fuel consumption statistics since last
reset
Press buttonÿ orè repeatedly
until the message
From start appears
in the multifunction display.
Press buttonj ork repeatedly
until the message
Since reset appears
in the multifunction display.
1Distance driven since last reset
2Time elapsed since last reset
3Average speed since last reset
4Average fuel consumption since last
resetResetting fuel consumption statistics
Press buttonÿ orè repeatedly
until the message
From Start appears
in the multifunction display.
Press buttonj ork repeatedly
until the reading that you want to reset
appears in the multifunction display.
Press and hold the reset button in the
instrument cluster (
page 130) until
the value is reset to
0.Distance to empty
Press buttonÿ orè repeatedly
until the message
From start appears
in the multifunction display.
Press buttonj ork repeatedly
until the message
Range: appears in
the multifunction display.
The calculated remaining driving range
based on the current fuel tank level
appears in the multifunction display.
iThe fuel consumption statistics From
Start
reset automatically to0 when either of
the following values is exceeded:

distance covered: 9 999 miles

time elapsed: 999 hours
The fuel consumption statistics
Since reset
reset automatically to
0 when either of the
following values is exceeded:

distance covered: 99 999 miles

time elapsed: 9 999 hoursiIf only very little fuel is left in the fuel tank,
the message
Range:--- appears in the multi-
function display.