steering wheel MERCEDES-BENZ G500 2008 W463 Owner's Guide

72 Safety and Security
Occupant safety
Safety guidelines for the seat belt,
emergency tensioning device and air
bagiAir bags are designed to deploy only in
certain frontal impacts (front air bags) and in
side impacts (window curtain air bags) which
exceed preset thresholds. Only during these
events will they provide their supplemental
protection.
The driver and passenger should always wear
their seat belts. Otherwis e it is not possible for
the air bags to provide their supplemental pro-
tection.
In case of other types of impacts and impacts
below air bag deployment thresholds, air bags
will not deploy. The driver and passenger will
then be protected to the extent possible by a
properly fastened seat belt. A properly fastened
seat belt is also needed to provide the best
possible protection in a rollover.
We caution you not to rely on the presence of the
air bags in order to avoid wearing your seat belt.
It is important to your safety and that of your pas-
senger that you replace deployed air bags and
repair any malfunctioning air bags to make sure
the vehicle will continue to provide supplemental
crash protection for occupants.
Warning!G

Damaged seat belts or seat belts that
were highly stressed in an accident
must be replaced and their anchoring
points must also be checked. Use only
seat belts installed or supplied at an au-
thorized Mercedes-Benz Light Truck
Center.

Air bags and Emergency Tensioning
Devices (ETDs) are designed to function
on a one-time-only basis. An air bag or
ETD that has deployed must be
replaced.

Do not pass seat belt s over sharp edges.
They could tear.

Do not make any modification that could
change the effectiveness of the seat
belts.

Do not bleach or dye seat belts as this
may severely weaken them. In a crash
they may not be able to provide ade-
quate protection.

No modifications of any kind may be
made to any components or wiring of
the SRS. This includes changing or
removing any component or part of the
SRS, the installation of additional trim
material, badges, etc. over the steering
wheel hub, front passenger front air bag
cover, outboard sides of the front seat
backrests, door trim panels, or door
frame trims, and installation of
additional electrical/electronic equip-
ment on or near SRS components and
wiring. Keep area between air bags and
occupants free from objects (e.g. pack-
ages, purses, umbrellas, etc.).

Air bag system components will be hot
after an air bag has inflated. Do not
touch.

Never place your feet on the instrument
panel, dashboard, or on the seat. Always
keep both feet on the floor in front of the
seat.
W463.boo Seite 72 Montag, 19. November 2007 8:41 08

88 Safety and Security
Driving safety systems
Continuous steady brake pedal pressure
yields the advantages provided by the ABS,
namely braking power and the ability to
steer the vehicle.
On slippery road surfaces, the ABS will
respond even to light brake pressure. The
pulsating brake pedal can be an indication
of hazardous road conditions and func-
tions as a reminder to take extra care while
driving.
The - indicator lamp in the instrument
cluster (
page 26) comes on when you
turn the SmartKey to position 2. It goes
out when the engine is running. Braking
At the instant one of the wheels is about to
lock up, a slight pulsation can be felt in the
brake pedal, indicating
that the ABS is in
the regulating mode.
Keep firm and steady pressure on the
brake pedal while experiencing the
pulsation. Emergency brake maneuver
Keep continuous full pressure on the
brake pedal.
Warning!G
When the ABS is malf
unctioning, the BAS,
the EBB, the ESP®, and the 4-ETS are also
switched off. The basic driving and braking
functions are still available.
When the ABS is malfunctioning, the wheels
may lock during hard braking, reducing
steering capability and extending the brak-
ing distance.
W463.boo Seite 88 Montag, 19. November 2007 8:41 08

89
Safety and Security
Driving safety systems
LOW RANGE– ABS
During off-road driving a special low range
system for the Antilock Brake System
(ABS) is operational with transfer case in
position LOW (
page 170).
An improved braking action (dig-in effect)
is obtained for vehicle speeds up to
37 mph (60 km/h) through a change in the
ABS control function.
For more information, see “Practical hints”
(
page 324).
BAS
The Brake Assist System (BAS) operates in
emergency situations. If you apply the
brakes very quickly, the BAS automatically
provides full brake boost, thereby poten-
tially reducing braking distance. Apply con-
tinuous full braking pressure until the
emergency braking situation is over. The
ABS will prevent the wheels from locking.
When you release the brake pedal the
brakes function again as normal. The BAS
is then deactivated.
With the BAS malfunctioning, the ABS,
ESP
®, and 4-ETS are also switched off.
Warning!G
The ABS cannot prevent the natural laws of
physics from acting on the vehicle, nor can
it increase braking or steering efficiency
beyond that afforded by the condition of the
vehicle brakes and tires or the traction
afforded. The ABS cannot prevent acci-
dents, including th ose resulting from
excessive speed in turn s, following another
vehicle too closely, or hydroplaning. Only a
safe, attentive, and skillful driver can pre-
vent accidents. The capabilities of an ABS
equipped vehicle must never be exploited in
a reckless or dangerous manner which
could jeopardize the user’s safety or the
safety of others.
Warning!G
If the BAS is malfunctioning, the brake
system is still functi oning normally, but
without the additional brake boost available
that BAS would normally provide in an emer-
gency braking maneuver. Therefore, the
braking distance may increase.
W463.boo Seite 89 Montag, 19. November 2007 8:41 08

91
Safety and Security
Driving safety systems
For more information, see “Practical hints”
(
page 330).
EBB
The Electronic Brake Booster (EBB)
enhances braking effectiveness by allow-
ing the rear brakes to supply a greater
proportion of the braking
effort in straight
line braking circumstances without a loss
of vehicle stability.
For more information, see the “Practical
hints” section (
page 327).
ESP®
The Electronic Stability Program (ESP®) is
operational as soon as the engine is run-
ning and monitors the vehicle’s traction
(force of adhesive friction between the
tires and the road surface) and handling.
The ESP
® recognizes when a wheel is
spinning or if the vehicle starts to skid.
By applying the brakes to the appropriate
wheel and by limiting engine output, the
ESP
® works to stabilize the vehicle.
The ESP® is especially useful while driving
off and on wet or slippery road surfaces.
The ESP
® also stabilizes the vehicle during
braking and steering maneuvers.
The ESP
® warning lamp v in the instru-
ment cluster (
page 26) flashes when the
ESP® is engaged.
The ESP
® warning lamp v comes on
when you switch on ignition (
page 39).
It goes out when the engine is running.
!Operational or performance test must only
be conducted on a two-axle dynamometer. If
such tests are necessary, contact an authorized
Mercedes-Benz Light Truck Center. You could
otherwise seriously damage the brake system or
the transfer case which is not covered by the
Mercedes-Benz Limited Warranty.
!Because the ESP® operates automatically,
the engine and ignition must be shut off
(SmartKey in starter switch position 0 or 1)
when testing the parking brake on a brake test
dynamometer and such testing should be no
longer than 10 seconds.
Active braking action through ESP
® may
otherwise seriously damage the brake system
which is not covered by the Mercedes-Benz
Limited Warranty.
Warning!G
If the EBB is malfun ctioning, the brake
system is still functionin g. However, the rear
wheels may lock during hard braking, caus-
ing you to lose control over the vehicle and
possibly causing an accident. Adjust your
driving style to the non-operating status of
the EBB.
W463.boo Seite 91 Montag, 19. November 2007 8:41 08

114 Controls in detail
Memory function
Prior to operating the vehicle, the driver
should check and adjust the seat height,
seat position fore and aft, and seat back-
rest angle if necessary, to ensure adequate
control, reach and comfort. The head
restraint should also be adjusted for
proper height. See also the section on
air bags (
page 70) for proper seat
positioning.
In addition, adjust the steering wheel to
ensure adequate control, reach, operation
and comfort. Both the interior and exterior
rear view mirrors should be adjusted for
adequate rear vision.
Fasten seat belts. Infants and small
children should be se ated in a properly
secured restraint system that complies
with U.S. Federal Motor Vehicle Safety
Standards 213 and 225 and Canadian
Motor Vehicle Safety Standards 213 and
210.2. With the memory function you can store up
to three different configurations.
Each stored position on the driver’s side
includes the following settings:

Seat position

Multicontour seat*: previously saved
setting

Steering wheel position

Exterior rear view mirrors’ position
Each stored position on the passenger side
includes the following settings:

Seat position

Multicontour seat*: previously saved
setting
Warning!G
Do not activate the memory function while
driving. Activating the memory function
while driving could cause the driver to lose
control of the vehicle.
W463.boo Seite 114 Montag, 19
. November 2007 8:41 08

115
Controls in detail
Memory function
The memory button and memory position
button are located on each front door.
1
Memory button
1, 2, 3 Memory position button
Switch on the ignition (page 39).
or
Open the respective door.
Storing positions into memory
Adjust the seats (page 42).
On the driver’s side, additionally adjust
the steering wheel (
page 44) and
exterior rear view mirrors (
page 46)
to the desired positions.
Press memory button 1.
Release memory button 1 and press
memory position button 1, 2 , or 3 with-
in 3 seconds.
All settings are stored to the selected
position.
Recalling positions from memory
Press and hold memory position
button 1, 2 , or 3 until the seat, steering
wheel and exterior rear view mirrors
have fully moved to the stored posi-
tions.
!Do not operate the power seats using
memory button 1 if the seat backrest is in an
excessively reclined position. Doing so could
cause damage to front or rear seats.
Move seat backrest to an upright position first.
iReleasing the memory position button stops
movement to the stored positions immediately.
W463.boo Seite 115 Montag, 19 . November 2007 8:41 08

116 Controls in detail
Memory function
Storing exterior rear view mirror
parking position (Canada only)
For easier parking, you can adjust the
passenger-side exterior rear view mirror so
that you can see the rear wheel and the
road curb as soon as you engage reverse
gearR.
For information on activating the parking
position, see “Activating exterior rear view
mirror parking position (Canada only)”
(
page 178).
The memory button is located on the
driver’s door. The adjustment button and
exterior rear view mirror buttons are
located on the dashboard to the left of the
steering wheel. 1
Adjustment button
2 Driver’s side exterior rear view mirror
button
3 Passenger-side exterior rear view
mirror button
4 Memory button
Switch on the ignition (page 39).
Press button 3.
The passenger-side exterior rear view
mirror is selected.
Adjust the exterior rear view mirror
with adjustment button 1 so that you
see the rear wheel and the road curb.
Press memory button 4.
Within 3 seconds, press bottom of
adjustment button 1.
The parking position is stored if the
mirror does not move.
iIf the mirror does move, repeat the above
steps. After the setting is stored, you can move
the mirror again.
W463.boo Seite 116 Montag, 19 . November 2007 8:41 08

117
Controls in detail
Lighting
 Lighting
For information on how to switch on the
headlamps and use the turn signals, see
“Switching on headlamps” (
page 56)
and see “Turn signals” (
page 57).
Exterior lamp switch
The exterior lamp switch is located on the
dashboard to the left of the steering wheel.
iIf you drive in countries where vehicles drive
on the other side of the road than the country in
which the vehicle is registered, you must have
the headlamps modified for symmetrical low
beams. Relevant information can be obtained at
any authorized Mercedes-Benz Light Truck
Center.
1‚Standing lamps, left
(turn left two stops)
2ˆStanding lamps, right
(turn left one stop)
3MOff
Daytime running lamp mode
(
page 119)
4UAutomatic headlamp mode
Daytime running lamp mode
(
page 119)
5CParking lamps (also tail lamps,
license plate lamps, side mark-
er lamps, instrument panel
lamps)
6BLow beam headlamps or high
beam headlamps
7‡Front fog lamps
8†Rear fog lamp
iIf you hear a warning signal you have forgot-
ten to switch off the low beam headlamps or the
parking lamps before opening the driver’s door.
In addition the message
Switch off lights
appears in the multifunction display.
Switch off the low beam headlamps or the park-
ing lamps.
If the message
Turn off lights or remove
key
appears in the multifunction display remove
the SmartKey from the starter switch or switch
off the automatic headlamp mode.
!Failure to switch off the exterior lamps when
leaving the vehicle may result in a discharged
battery.
W463.boo Seite 117 Montag, 19 . November 2007 8:41 08

123
Controls in detail
Lighting
Driving forward
Switching on corner
-illuminating front
fog lamps
Depending on whether you are turning
left or right, switch on the left or right
turn signal (
page 57).
The respective front fog lamp comes on
and illuminates the area in the
direction into which you are turning.
or
Turn steering wheel in desired
direction.
The front fog lamp on the side of your
steering direction comes on. Switching off corner-illuminating front
fog lamps
The combination switch for the turn signal
resets automatically after major steering
wheel movements. This
will switch off the
corner-illuminating front fog lamps if they
were activated by switching on the left or
right turn signal.
If the turn signal should stay on after
making the turn, the turn signal and the
corner-illuminating fr ont fog lamps can be
switched off by returning the combination
switch to its original position.
iIf you have switched on the turn signal for
one side but turn the steering wheel in the
opposite direction, the corner-illuminating front
fog lamp comes on for the side indicated by the
turn signal.
The corner-illuminating front fog lamp remains lit
for a maximum of three minutes. Afterwards, it
goes out even if the turn signal is still switched
on.
iThe corner-illuminating front fog lamps
temporarily come on on both sides of the vehicle
if you turn the steering wheel in one direction
and then again in the other direction shortly
thereafter.
iThe corner-illuminating front fog lamps will
come on automatically depending on the steer-
ing angle, even if you did not switch on either
turn signal. If the corner-illuminating front fog
lamps came on automatically, they will also go
out automatically depending on the steering
angle.iThere may be a brief delay before the
corner-illuminating front fog lamps switch off.
W463.boo Seite 123 Montag, 19 . November 2007 8:41 08

131
Controls in detail
Instrument cluster
Coolant temperature gauge
The coolant temperat
ure gauge is on the
left side in the instrument cluster
(
page 26).
Resetting trip odometer
Make sure you are viewing the
standard display (
page 140).
If it is not displayed, press button è
or ÿ on the multifunction steering
wheel (
page 134) repeatedly until
the standard displa y appears in the
multifunction display.
Press and hold reset button 1
(
page 130) until the trip odometer is
reset.
Warning!G

Driving when your engine is overheated
can cause some fluids which may have
leaked into the engine compartment to
catch fire. You could be seriously
burned.

Steam from an overheated engine can
cause serious burns which can occur
just by opening the hood. Stay away
from the engine if you see or hear steam
coming from it.
Stop the vehicle in a safe location away from
other traffic. Turn off the engine, get out of
the vehicle and do not stand near the vehicle
until the engine has cooled down.
!Excessive coolant temperature triggers a
warning message in the multifunction display
(
page 346).
The engine should not be operated with the
coolant temperature above 248°F (120°C).
Doing so may cause serious engine damage
which is not covered by the Mercedes-Benz
Limited Warranty.
iDuring severe operating conditions, e.g.
stop-and-go traffic, the coolant temperature may
rise close to 248°F (120°C).
W463.boo Seite 131 Montag, 19 . November 2007 8:41 08