change time MERCEDES-BENZ G500 2008 W463 Owner's Manual

57
Getting started
Driving
High beam
The combination switch is located on the
left of the steering column.
Combination switch
1
High beam
2 High beam flasher
Push the combination switch in
direction of arrow 1.
The high beam headlamp indicator
lamp A in the instrument cluster
comes on (
page 26).
For more information on headlamps, see
“Lighting” (
page 117).
Turn signals
The combination switch is located on the
left of the steering column.
Combination switch
1 Turn signals, right
2 Turn signals, left
Press the combination switch in
direction of arrow 1 or 2.
The corresponding turn signal indicator
lamp K orL in the instrument
cluster flashes (
page 26).
The combination switch resets automati-
cally after major steering wheel move-
ments.
iTo signal minor directional changes such as
changing lanes, press co mbination switch only
to point of resistance and release. The corre-
sponding turn signals will flash three times.
W463.boo Seite 57 Montag, 19. November 2007 8:41 08

59
Getting started
Driving
Intermittent wiping
Only switch on intermittent wiping under
wet weather conditions or in the presence
of precipitation.
When you select intermittent wiping, the
rain sensor is activated. The rain sensor
automatically sets a suitable wiping
interval depending on the wetness of the
sensor surface.Turn the combination switch to
position
I.
After the initial wipe, pauses between
wipes are automatically controlled by
the rain sensor. Single wipe
Press the combination switch briefly in
direction of arrow
1 to the resistance
point.
The windshield wipers wipe one time
without washer fluid.
Wiping with windsh ield washer fluid
Push the combination switch in direc-
tion of arrow1 past the resistance
point.
The windshield wipers operate with
washer fluid.
For information on filling up the washer
reservoir, see “Windshield/rear window
washer system and headlamp cleaning
system” (
page 275).
!Do not leave windshield wipers in intermit-
tent setting when the vehicle is taken to an auto-
matic car wash or during windshield cleaning.
Windshield wipers will operate in the presence of
water sprayed on the windshield, and windshield
wipers may be damaged as a result.
iIntermittent wiping is interrupted when the
vehicle is at a standstill and a front door is
opened. This protects persons getting into or out
of the vehicle from being sprayed.
Intermittent wiping will be continued when all
doors are closed and

the gear selector lever is in drive position D
or reverse gear R
or

the wiper setting is changed using the
combination switchiTo prevent smears on the windshield, or
noisy/chattering wiper bl ades, wipe with wind-
shield washer fluid every now and then even
when it is raining.
W463.boo Seite 59 Montag, 19. November 2007 8:41 08

72 Safety and Security
Occupant safety
Safety guidelines for the seat belt,
emergency tensioning device and air
bagiAir bags are designed to deploy only in
certain frontal impacts (front air bags) and in
side impacts (window curtain air bags) which
exceed preset thresholds. Only during these
events will they provide their supplemental
protection.
The driver and passenger should always wear
their seat belts. Otherwis e it is not possible for
the air bags to provide their supplemental pro-
tection.
In case of other types of impacts and impacts
below air bag deployment thresholds, air bags
will not deploy. The driver and passenger will
then be protected to the extent possible by a
properly fastened seat belt. A properly fastened
seat belt is also needed to provide the best
possible protection in a rollover.
We caution you not to rely on the presence of the
air bags in order to avoid wearing your seat belt.
It is important to your safety and that of your pas-
senger that you replace deployed air bags and
repair any malfunctioning air bags to make sure
the vehicle will continue to provide supplemental
crash protection for occupants.
Warning!G

Damaged seat belts or seat belts that
were highly stressed in an accident
must be replaced and their anchoring
points must also be checked. Use only
seat belts installed or supplied at an au-
thorized Mercedes-Benz Light Truck
Center.

Air bags and Emergency Tensioning
Devices (ETDs) are designed to function
on a one-time-only basis. An air bag or
ETD that has deployed must be
replaced.

Do not pass seat belt s over sharp edges.
They could tear.

Do not make any modification that could
change the effectiveness of the seat
belts.

Do not bleach or dye seat belts as this
may severely weaken them. In a crash
they may not be able to provide ade-
quate protection.

No modifications of any kind may be
made to any components or wiring of
the SRS. This includes changing or
removing any component or part of the
SRS, the installation of additional trim
material, badges, etc. over the steering
wheel hub, front passenger front air bag
cover, outboard sides of the front seat
backrests, door trim panels, or door
frame trims, and installation of
additional electrical/electronic equip-
ment on or near SRS components and
wiring. Keep area between air bags and
occupants free from objects (e.g. pack-
ages, purses, umbrellas, etc.).

Air bag system components will be hot
after an air bag has inflated. Do not
touch.

Never place your feet on the instrument
panel, dashboard, or on the seat. Always
keep both feet on the floor in front of the
seat.
W463.boo Seite 72 Montag, 19. November 2007 8:41 08

78 Safety and Security
Occupant safety
Infant and child restraint systems
Only use a BabySmart
TM compatible child
restraint for the front passenger seat in
this vehicle.
We recommend all infants and children be
properly restrained at all times while the
vehicle is in motion.
All lap-shoulder belts except the driver’s
seat belt and the rear center seat belt have
special seat belt retractors for secure fas-
tening of child restraints.
To fasten a child restraint, follow child
restraint instructions for mounting. Then
pull the shoulder belt out completely and
let it retract. During seat belt retraction, a
ratcheting sound can be heard to indicate
that the special seat b elt retractor is acti-
vated. The seat belt is now locked. Push
down on child restraint to take up any
slack.Warning!G
Do not leave children unattended in the
vehicle, even if they are secured in a child
restraint system. The children could

injure themselves on parts of the vehicle

be seriously or fatally injured through
excessive exposure to extreme heat or
cold
Do not expose the child restraint system to
direct sunlight. The child restraint system’s
metal parts, for exampl e, could become very
hot, and the child could be burned on these
parts.
If children open a door, they could

injure other persons

get out of the car and injure themselves
or be injured by following traffic
Do not carry heavy or hard objects in the
passenger or cargo compartment unless
they are firmly secured in place. For more
information, see “Loading” (
page 206)
and “Useful features” (
page 215).
Unsecured or improperly positioned cargo
increases a child’s risk of injury in the event
of

strong braking maneuvers

sudden changes of direction

an accident
W463.boo Seite 78 Montag, 19. November 2007 8:41 08

147
Controls in detail
Control system
Submenus in the Settings menu
Press button
j.
The collection of the submenus
appears in the multifunction display.
Press button ç.
The selection marker moves to the next
submenu. The submenus are arranged by hierarchy.
Scroll down with button
ç, scroll up
with button æ.
With the selection marker on the desired
submenu, use button j to access the
individual functions within that submenu.
Once within that submenu, you can use
button j to move to the next function
or button k to move to the previous
function within that submenu.
The settings themselves are made with
button æ orç .
iThe settings you have changed will not be
reset unless you confirm the action by pressing
the reset button a second time.
After approximately 5 seconds, the
Settings
menu reappears in the multifunction display
(
page 146).
iFor safety reasons, the function Headlamp
mode
in the Lighting submenu cannot be reset
while driving.
The following message appears in the
multifunction display:
Settings
Cannot be completely
reset to factory
settings while driving
W463.boo Seite 147 Montag, 19 . November 2007 8:41 08

148 Controls in detail
Control system
The table below shows what settings can
be changed within the various menus.
Detailed instructions on making individual
settings can be found on the following
pages.
Instrument clusterLightingVehicleConvenience
(page 149)(page 151)(page 154)(page 156)
Selecting speedometer
display modeSetting daytime
running lamp mode
(USA only)Selecting audio search
functionActivating
easy-entry/exit feature
Selecting languageSetting locator lightingSetting automatic
locking
Selecting display
(digital speedometer or
outside temperature)
for status indicatorSetting night security
illumination
Setting interior lighting
delayed shut-off
W463.boo Seite 148 Montag, 19. November 2007 8:41 08

151
Controls in detail
Control system
Lighting submenu
Access the
Lighting submenu via the
Settings menu. Use the Lighting
submenu to change the lamp and lighting
settings on your vehicle.
The following functions are available:
Setting daytime running lamp mode
(USA only)
Move the selection marker with
button
æ orç to the
Lighting
submenu.
Press button j ork repeatedly
until the message
Headlamp mode
appears in the multifunction display.
The selection marker is on the current
setting.
Press button æ orç to select
manual operation (
Manual) or daytime
running lamp mode (
Constant).
With daytime running lamp mode activated
and the exterior lamp switch in
position M orU , the low beam
headlamps are switched on when the
engine is running.
In low ambient light conditions the
following lamps will switch on additionally:

Parking lamps

Tail lamps

License plate lamps

Side marker lamps
FunctionPage
Setting daytime running lamp
mode (USA only)151
Setting locator lighting152
Setting night security
illumination153
Setting interior lighting delayed
shut-off154
iCanada vehicles:
This function is not available as the daytime
running lamp mode is mandatory and therefore
in a constant mode.
W463.boo Seite 151 Montag, 19 . November 2007 8:41 08

196 Controls in detail
Power tilt/sliding sunroof
Switch on the ignition (page 39).Opening and closing the tilt/sliding
sunroof
To open, close, raise, or lower the
tilt/sliding sunroof, move the sunroof
switch to the resistance point in the
required direction of arrows
1 to 4
(
page 195).
Release the sunroof switch when the
tilt/sliding sunroof has reached the
desired position.
Fully opening the tilt/sliding sunroof
(Express-open)
Move the sunroof switch past the
resistance point in direction of
arrow 4 (
page 195) and release.
The tilt/sliding sunroof opens
completely. Stopping the tilt/slid
ing sunroof during
Express-operation
Move the sunroof switch in any
direction.
The movement of the tilt/sliding
sunroof stops.
!Please keep in mind that weather conditions
can sometime change rapidly. Make sure to
close the tilt/sliding sunroof when leaving the
vehicle. If water enters the vehicle interior,
vehicle electronics could be damaged which is
not covered by the Mercedes-Benz Limited
Warranty.
iWhen the tilt/sliding sunroof is open,
resonance noises may result in addition to the
usual wind noises. They are caused by minimal
pressure changes in the passenger compart-
ment. To reduce or eliminate these noises,
change the position of the tilt/sliding sunroof or
open a side window slightly.
iYou can also open or close the tilt/sliding
sunroof using the SmartKey, see “Summer open-
ing feature” (
page 193) and see “Convenience
closing feature” (
page 194).
Warning!G
The opening procedure of the tilt/sliding
sunroof can be immediately halted by
releasing the switch or , if the switch was
moved past the resistance point and
released, by moving the switch in any
direction.
The closing procedure of the tilt/sliding sun-
roof can be immediately halted by releasing
the switch.
The closing procedure of the tilt/sliding sun-
roof can be immediately reversed by moving
the switch in direction 1 or4.
W463.boo Seite 196 Montag, 19 . November 2007 8:41 08

197
Controls in detail
Driving systems
 Driving systems
The driving systems of your vehicle are
described on the following pages:

Cruise control (page 197), with
which the vehicle can maintain a preset
speed.

Rear Parking Assist (page 200) and
rear view camera (
page 203), which
serve as parking aid.
For information on the ABS, BAS, ESP
®,
4-ETS, and EBB driving systems, see “Driv-
ing safety systems” (
page 87).
Cruise control
The cruise control automatically maintains
the speed you set for your vehicle.
The use of the cruise control is recom-
mended for driving at a constant speed for
extended periods of time. You can set or
resume the cruise control at any speed
over 20 mph (30 km/h).
The cruise control function is operated by
means of the cruise control lever.
The cruise control lever is the uppermost
lever found on the left-hand side of the
steering column (
page 24).
iThe cruise control should not be activated
during-off road driving.
Warning!G
The cruise control is a convenience system
designed to assist the driver during vehicle
operation. The driver is and must always
remain responsible for the vehicle’s speed
and for safe brake operation.
Only use the cruise cont rol if the road, traffic
and weather conditions make it advisable to
travel at a steady speed.

The use of the cruise control can be
dangerous on winding roads or in heavy
traffic because conditions do not allow
safe driving at a steady speed.

The use of the cruise control can be
dangerous on slippery roads. Rapid
changes in tire traction can result in
wheel spin and loss of control.

Deactivate the cruise control when
driving in fog.
The “Resume” function should only be
operated if the driver is fully aware of the
previously set speed and wishes to resume
this particular preset speed.
W463.boo Seite 197 Montag, 19 . November 2007 8:41 08

238 Controls in detail
Useful features
Step 2:
If you have previously programmed a
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold outer signal transmitter
buttons2 and 4 and release them
only when indicator lamp 1 begins to
flash after approximately 20 seconds
(do not hold the button for longer than
30 seconds). This procedure erases
any previous settings for all three
channels and initializes the memory.
If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and
begin directly with step 3. Step 3:Hold end of hand-held remote
control
5 of the device you wish to
train approximately 2 to 5 in
(5 to12 cm) away from signal trans-
mitter button ( 2, 3 or 4) to be
programmed, while keeping indicator
lamp 1 in view.
Step 4:
Using both hands, simultaneously
press hand-held remote control
button 6 and the desired signal
transmitter button ( 2, 3 , or 4). Do
not release the buttons until step 5 is
completed.
Indicator lamp 1 will flash, first slowly
and then rapidly. Step 5:
After indicator lamp
1 changes from a
slow to a rapidly flashing light, release
the hand-held remote control button
and the signal transmitter button.
Step 6:
Press and hold the just-trained signal
transmitter button ( 2, 3 , or 4) and
observe indicator lamp 1.
If indicator lamp 1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button ( 2, 3 , or 4) is pressed and
released.
Step 7:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
iIndicator lamp 1 flashes immediately the
first time the signal transmitter button is
programmed. If this button has already been
programmed, the indicator lamp will only start
flashing after 20 seconds.
iIf indicator lamp 1 flashes rapidly for about
2 seconds and then turns to a constant light,
continue with programming steps 8 through 12
as your garage door opener may be equipped
with the “rolling code” feature.

W463.boo Seite 238 Montag, 19 . November 2007 8:41 08