check engine light MERCEDES-BENZ G500 2008 W463 Owner's Manual

39
Getting started
Unlocking
Press unlock button
Πon the
SmartKey.

All turn signal lamps flash once.

The locking knobs in the doors
move up.

The anti-theft alarm system is
disarmed.

The locator lighting comes on if the
feature is enabled in the control
system (
page 152).
Enter the vehicle and insert the
SmartKey in the starter switch.
For more information, see “Locking and
unlocking” (
page 100).
Starter switch positions
SmartKey
Starter switch
0 For removing SmartKey
The steering is locked when the
SmartKey is removed from the starter
switch.
1 Power supply for some electrical
consumers, such as seat adjustment
2 Ignition (power supply for all electrical
consumers) and driving position
All lamps (except high beam headlamp
indicator lamp and turn signal indicator
lamps unless activated) in the instru-
ment cluster come on. If a lamp in the
instrument cluster fails to come on
when the ignition is switched on, have
it checked and replaced if necessary. If
a lamp in the instrument cluster
remains on after starting the engine or
comes on while driving, refer to “Lamps
in instrument cluster” (
page 324).
3 Starting position
Warning!G
When leaving the vehicl e, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. A child’s
unsupervised access to a vehicle could
result in an accident and/or serious
personal injury.
W463.boo Seite 39 Montag, 19. November 2007 8:41 08

58 Getting started
Driving
Windshield wipers
The combination switch is located on the
left of the steering column.
Combination switch
1Single wipe
Wiping with windshield washer fluid
2 Switching on windshield wipers
Switch on the ignition (page 39). Switching on windshield wipers
Turn the combination switch to the
desired position depending on the
intensity of the rain.
0
Windshield wipers off
I Intermittent wiping
II Normal wiper speed
III Fast wiper speed
!Do not operate the windshield wipers when
the windshield is dry. Dust that accumulates on
a windshield might scratch the glass and/or
damage the wiper blades when wiping occurs on
a dry windshield. If it is necessary to operate the
windshield wipers in dry weather conditions,
always operate the windshield wipers with
windshield washer fluid (
page 59).
!If anything blocks the windshield wipers
(leaves, snow, etc.), switch them off
immediately.

For safety reasons, stop the vehicle in a safe
location, turn off the engine and remove the
SmartKey from the starter switch before
attempting to remove any blockage.

Remove blockage.

Turn the windshield wipers on again.
If the windshield wipers fail to function at all with
the combination switch in position I,

set the combination switch to the next
higher wiper speed

have the windshield wipers checked at the
nearest authorized Mercedes-Benz Light
Truck Center.
W463.boo Seite 58 Montag, 19. November 2007 8:41 08

61
Getting started
Driving
Problems while driving
The engine runs erratically and misfires

An ignition cable may be damaged.

The engine electronics may not be
operating properly.

Unburned gasoline may have entered
the catalytic converter and damaged it.
Give very little gas.
Have the problem repaired at an
authorized Mercedes
-Benz Light Truck
Center as soon as possible. The coolant temperature is above
248°F (120°C)
The coolant is too hot and is no longer
cooling the engine.
Stop the vehicle in a safe location as
soon as possible and turn off the
engine. Allow engine and coolant to
cool off.
Check the coolant level and add
coolant if necessary (
page 274).
In case of accident
If the vehicle is leaking fuel:
Do not start the engine under any
circumstances.
Notify local fire and/or police
authorities.
If the extent of the damage cannot be
determined:
Contact an authoriz ed Mercedes-Benz
Light Truck Center or call Roadside
Assistance.
If no damage can be determined on the

major assemblies

fuel system

engine mount:
Start the engine in the usual manner.
iExcessive coolant temperatures trigger a
warning message in the multifunction display
(
page 346).
W463.boo Seite 61 Montag, 19. November 2007 8:41 08

169
Controls in detail
Automatic transmission
Canceling gear range limit
Press and hold the gear selector lever
in the
D+direction until
Dreappears in
the multifunction display (
page 164).
The transmission will shift from the
current gear range directly to gear
range D.
Shifting into optimal gear range
Press and hold the gear selector lever
in the D-direction.
The transmission will automatically
select the gear range suited for optimal
acceleration and deceleration. This will
involve shifting down one or more
gears. Emergency operation
(Limp-Home Mode)
If vehicle acceleration becomes less
responsive or sluggish or the transmission
no longer shifts, the transmission is most
likely operating in limp-home (emergency
operation) mode. In this mode only second
gear and reverse gear can be selected.
Stop the vehicle in a safe location.
Move the gear selector lever to park
position
P.
Turn off the engine.
Wait at least 10 seconds before
restarting.
Restart the engine.
Move the gear selector lever to
position D (for second gear) or
position R.
Have the transmission checked at an
authorized Mercedes -Benz Light Truck
Center as soon as possible.
W463.boo Seite 169 Montag, 19 . November 2007 8:41 08

190 Controls in detail
Climate control
Activating
Moist air can fog up the windows. You can
dehumidify the air with the air condition-
ing.
Press button9 (page 183) once
more.
The indicator lamp on the button
comes on.
The air conditioning uses the refrigerant
R134a. This refrigerant is free of CFCs
which are harmful to the ozone layer.
Residual heat and ventilation
With the engine switched off, it is possible
to continue to heat or ventilate the interior
for up to 30 minutes. This feature makes
use of the residual he at produced by the
engine. Activating
Turn the SmartKey in the starter switch
to position
0 or 1 (
page 39).
or
Remove the SmartKey from the starter
switch.
Press button 9 (page 183).
The indicator lamp on the button
comes on.
Deactivating
Press button 9 (page 183) once
more.
The indicator lamp on the button goes
out.!If the air conditioning cannot be turned on
again, this indicates that the air conditioning is
losing refrigerant. The compressor has turned
itself off.
Have the air conditioning checked at the nearest
authorized Mercedes-Benz Light Truck Center.
iHow long the system will provide heating
depends on

the coolant temperature

the battery voltage
Regardless of the temperature and air volume
set on the climate control panel, an interior
temperature is aimed at by 72°F (22°C) and the
blower runs on low speed to protect the vehicle
battery.
iThe residual heat is automatically turned off:

when the ignition is switched on

after about 30 minutes

if the coolant temperature is too low

if the battery voltage drops
W463.boo Seite 190 Montag, 19 . November 2007 8:41 08

247
Operation
Driving instructions
Refer to the description of the Brake Assist
System (BAS) (
page 89).
Brake pad wear or a leak in the system may
be the reason for low brake fluid in the
reservoir.
The brake fluid level in the reservoir may
be too low if the brake warning lamp in the
instrument cluster comes on although the
parking brake is released (
page 326).
Observe additional messages in the
multifunction display that may appear
(
page 336).
Have the brake system inspected
immediately. Contact an authorized
Mercedes-Benz Light Truck Center.
All checks and service work on the brake
system should be carried out by qualified
technicians only. Contact an authorized
Mercedes-Benz Light Truck Center.
Only install brake pads and brake fluid
recommended by Mercedes-Benz. After hard braking, it is advisable to drive
on for some time, rather than immediately
park, so the air stream will cool down the
brakes faster.
Driving off
Apply the brakes to test
them briefly after
driving off. Perform this procedure only
when the road is clear of other traffic.
Warm up the engine smoothly. Do not
place full load on the engine until the
operating temperature has been reached.
To ensure sufficient traction during
off-road driving, activate differential locks
as needed (
page 175).
Warning!G
If other than recommended brake pads are
installed, or other than recommended brake
fluid is used, the braking properties of the
vehicle can be degraded to an extent that
safe braking is substa ntially impaired. This
could result in an accident.
!When driving down long and steep grades,
relieve the load on the brakes by shifting into a
lower gear to use the engine’s braking power.
This helps prevent overheating of the brakes and
reduces brake pad wear.
!When driving off on a slippery surface, do
not allow a drive wheel to spin for an extended
period with the ESP
® switched off. Doing so may
cause serious damage to the drivetrain which is
not covered by the Mercedes-Benz Limited
Warranty.
!Simultaneously depressing the accelerator
pedal and applying the brake reduces engine
performance and causes premature brake and
drivetrain wear.
W463.boo Seite 247 Montag, 19 . November 2007 8:41 08

260 Operation
Driving instructions

Check the vehicle clearance before
driving in ruts.

Comply with the warnings
(
page 253) and rules for off-road
driving (
page 253).

Select gear range 1 on the automatic
transmission (
page 167).

Drive slowly next to the ruts rather than
through them if at all possible.

If the ruts are too deep to drive in, drive
with one side of the vehicle on the
grassy center strip if the route permits. Returning from off-road driving
Off-road driving increases strain on the
vehicle.
We recommend that you inspect the vehi-
cle for possible damage after each off-road
trip. Recognizing any damage and a subse-
quent timely repair reduces the chance of
a possible breakdown or accident later on.
Proceed as follows:

Switch the transfer case in position
HIGH (
page 170).

Switch differential locks off
(
page 176).

Clean all exterior lamps and check
them for possible damage.

Clean the front and rear license plate.

Remove excessive dirt from tires,
wheels, wheel housings, and under-
body.
For instance, after driving in mud, clean
the radiator, chassis, engine, brakes,
and wheels from extreme dirt using a
strong jet of water.
After off-road driving or crossing obstacles,
inspect vehicle for any damage, especially
vehicle underbody and suspension components.
Failure to do so can adversely affect the vehi-
cle’s future performance, including increased
chance of an accident.
Warning!G
Never drive on pavement with activated
differential locks. Engaged front axle differ-
ential locks limits ability to move around
curves.
If you feel a sudden significant vibration or
ride disturbance, or you suspect that possi-
ble damage to your vehicle has occurred,
you should turn on the hazard warning flash-
ers, carefully slow down, and drive with cau-
tio n to an a rea whic h is a s afe d ista nc e fro m
the roadway.
Inspect the tires and under the vehicle for
possible damage. If the vehicle or tires
appear unsafe, have it towed to the nearest
Mercedes-Benz Light Truck Center or tire
dealer for repairs.
Damage to the vehicle may influence driving
comfort and poses the risk of accident to
you and other drivers.
W463.boo Seite 260 Montag, 19 . November 2007 8:41 08

265
Operation
At the gas station
Only fill your tank until the filler nozzle
unit cuts out –
do not top off or
overfill .
Replace fuel filler cap 2 by turning it
clockwise until it audibly engages.
Close fuel filler flap 1.
You should hear the latch close shut.
Check regularly and before a long trip
For information on quantities and require-
ments of operating agents, see “Fuels,
coolants, lubricants, etc.” (
page 420).
Open the hood (page 267).
G 500
1 Coolant
2 Brake fluid
Warning!G
Overfilling of the fuel tank may create pres-
sure in the system which could cause a gas
discharge. This could cause the gas to spray
back out when removing the fuel pump noz-
zle, which could caus e personal injury.
!When refueling the vehicle, make certain
that no gasoline comes into contact with the rear
side marker to prevent damaging the lens.
iMake sure to close the fuel filler flap before
locking your vehicle as the flap locking pin
prevents closing after you have locked the
vehicle.
iLeaving the engine running and the fuel cap
open can cause the ? malfunction indicator
lamp (USA only) or the ± malfunction indica-
tor lamp (Canada only) comes on.
For more information, see “Practical hints”
(
page 328).
iOnly use premium unleaded gasoline with a
minimum Posted Octane Rating of 91 (average of
96 RON/86 MON). Information on gasoline
quality can normally be found on the fuel pump.
Please contact gas station personnel in case la-
bels on the pump cannot be found.
For more information on gasoline, see “Premium
unleaded gasoline” (
page 424), refer to the
Factory Approved Service Products pamphlet
(USA only), or contact an authorized
Mercedes-Benz Light Truck Center.
W463.boo Seite 265 Montag, 19 . November 2007 8:41 08

266 Operation
At the gas station
G55AMG
1Coolant
2 Brake fluid Brake fluid
Coolant
For normal replenishing, use water
(potable water quality).
For more information, see “Coolant level”
(
page 274) and see “Fuels, coolants, lu-
bricants, etc.” (
page 420). Engine oil level
For more information on engine oil, see
“Engine oil” (
page 269).
Windshield/rear window washer sys-
tem and headlamp cleaning system
For more information on refilling the
washer reservoir, see “Windshield/rear
window washer syst em and headlamp
cleaning system” (
page 275).
Vehicle lighting
Check function and cleanliness.
For information on replacing light bulbs,
see “Replacing bulbs” (
page 375).
For more information, see “Exterior lamp
switch” (
page 117).
Tire inflation pressure
For more information, see “Checking tire
inflation pressure” (
page 288).
!If you find that the brake fluid in the brake
fluid reservoir has fallen to the minimum mark or
below, have the brake system checked for brake
pad thickness and leaks immediately. Notify an
authorized Mercedes-Benz Light Truck Center
immediately. Do not add brake fluid as this will
not solve the problem.
For more information, see “Practical hints”
(
page 326) and see “Brake fluid”
(
page 423).
W463.boo Seite 266 Montag, 19 . November 2007 8:41 08

269
Operation
Engine compartment
ClosingLower hood and let it drop into lock
from a height of approximately 0.7 ft
(20 cm).
The hood will lock audibly.
Check to make sure the hood is fully
closed.
If you can raise the hood at a point
above the turn signals to the left and
right of the hood, then it is not properly
closed. Open it again and let it drop
with somewhat greater force.
Engine oil
The amount of oil your engine needs will
depend on a number of factors, including
driving style. Higher
oil consumption can
occur when

the vehicle is new

the vehicle is driven frequently at
higher engine speeds
Engine oil consumption checks should only
be made after the vehicle break-in period.
Warning!G
When closing the hood, use extreme caution
not to catch hands or fi ngers. Be careful that
you do not close the hood on anyone.
Make sure that the hood is securely
engaged before driving off. Do not continue
driving if the hood can no longer engage
after an accident, for example. The hood
could otherwise come loose while the
vehicle is in motion and endanger you and
others.
!Do not push the hood closed manually, as
this could damage it. !Do not use any special lubricant additives,
as these may damage the drive assemblies.
Using special additives not approved by
Mercedes-Benz may cause damage not covered
by the Mercedes-Benz Limited Warranty.
More information on this subject is available at
any Mercedes-Benz Light Truck Center.
W463.boo Seite 269 Montag, 19 . November 2007 8:41 08