warning light MERCEDES-BENZ G55AMG 2008 W463 Manual Online

377
Practical hints
Replacing bulbs
Notes on bulb replacement

Only use 12-volt bulbs of the same type
and with the specified watt rating.

Switch lights off before changing a bulb
to prevent short circuits.

Always use a clean lint-free cloth when
handling bulbs.

Your hands should be dry and free of oil
and grease.

If the newly installed bulb does not
come on, contact an authorized
Mercedes-Benz Light Truck Center.
Have the LEDs and bulbs for the following
lamps replaced at an authorized
Mercedes-Benz Light Truck Center:

the additional turn signal lamps in the
exterior rear view mirrors

the high mounted brake lamp

the Bi-Xenon lamps

the locator lighting lamps in the
exterior rear view mirrors
Warning!G
Bulbs and bulb sockets can be very hot.
Allow the lamp to cool down before
changing a bulb.
Keep bulbs out of reach of children.
Halogen lamps contain pressurized gas.
A bulb can explode if you:

touch or move it when hot

drop the bulb

scratch the bulb
Wear eye and hand protection.
Because of high voltage in Xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.
!Do not replace the LEDs yourself. You could
otherwise damage the LEDs or parts of the vehi-
cle. Only have the LEDs replaced at an autho-
rized Mercedes-Benz Light Truck Center.
W463.boo Seite 377 Montag, 19 . November 2007 8:41 08

386 Practical hints
Replacing wiper blades
Wiper blades
Remove the SmartKey from the starter
switch.Removing
Fold the wiper arms forward until they
engage.
1 Safety tab
2 Wiper blade
3 Wiper arm
4 Attachment link
Warning!G
For safety reasons, switch off wipers and
remove SmartKey from starter switch
before replacing a wipe r blade. Otherwise,
the wiper motor could suddenly turn on and
cause injury.
Warning!G
Wiper blades are components that are
subject to wear and tear. Replace the wiper
blades twice a year, preferably in the spring
and fall. Otherwise the windows will not be
properly wiped. As a result, you may not be
able to observe surrounding traffic condi-
tions and could cause an accident.
!Never open the hood when the wiper arm is
folded forward.
Hold on to the wiper when folding the wiper arm
back. If released, the force of the impact from
the tensioning spring could crack the windshield.
Do not allow the wiper arms to contact the wind-
shield glass without a wiper blade inserted.
For your convenience, you should have this work
carried out at an authorized Mercedes-Benz
Light Truck Center.!Do not pull on the wiper blade inserts. They
could tear.
W463.boo Seite 386 Montag, 19 . November 2007 8:41 08

388 Practical hints
Flat tire
When you replace the vehicle’s tires, you
can use the spare wheel as a regular wheel
if:

it is not more than 6 years old

rim and tire are the same model as the
regular wheels
Preparing the vehicle
Park the vehicle in a safe distance from
moving traffic on a hard, flat surface
when possible.
Turn on the hazard warning flasher
(
page 124).
Turn the steering wheel so that the
front wheels are in a straight-ahead
position.
Set the parking brake (page 62).
Move the gear selector lever to park
position P (
page 162).
Turn off the engine (page 64).
Remove the SmartKey from the starter
switch.
Have any passenger exit the vehicle at
a safe distance from the roadway.
Warning!G
If the spare tire is more than 6 years old or
is not the same model as the regular tires,
have the spare tire replaced with a new tire
at the nearest Mercedes-Benz Light Truck
Center.
Never operate the vehicle with more than
one spare wheel mounted.
Warning!G
G55AMG:
Vehicles with different tire dimensions on
the front and rear axle: rim and tire size of
spare wheel and regular wheel differ.
Handling will be adversely affected when the
spare wheel is used.
Do not exceed the maximum speed of
50 mph (80 km/h).
iOpen door only when conditions are safe to
do so.
W463.boo Seite 388 Montag, 19 . November 2007 8:41 08

392 Practical hints
Flat tire
Mounting the new wheel
Clean contact surfaces of wheel and
wheel hub.
Push the wheel onto the wheel hub and
press firmly.
Insert wheel bolts and tighten them
slightly. Lowering the vehicle
Using the pump handle, turn the
release bolt of the jack counter-
clockwise approximately one turn
(
page 390).
Lower the vehicle until it is resting fully
on its own weight.
Remove the jack.
!To avoid paint damage, place wheel flat
against hub and hold it there while installing first
wheel bolt.
Warning!G
Always replace wheel bolts that are
damaged or rusted.
Never apply oil or grease to wheel bolts.
Damaged wheel hub threads should be
repaired immediately. Do not continue to
drive under these circumstances! Contact
an authorized Mercedes-Benz Light Truck
Center.
Incorrect wheel bolts or improperly tight-
ened wheel bolts can cause the wheel to
come off. This could cause an accident.
Make sure to use the correct wheel bolts.
Warning!G
Only use genuine Mercedes-Benz wheel
bolts. Other wheel bolts may come loose.
Do not tighten the wheel bolts when the
vehicle is raised. Otherwise the vehicle
could tip over.
iNever turn the release bolt of the jack more
than one or two revolut ions. Otherwise hydraulic
fluid can escape.
W463.boo Seite 392 Montag, 19 . November 2007 8:41 08

394 Practical hints
Battery
The battery is located in front of the rear
seat bench and below the cup holder.
Jump starting terminals are located on the
driver’s side of the engine compartment
(
page 398).
The battery should always be sufficiently
charged in order to achieve its rated
service life. Refer to Maintenance Booklet
for battery maintenance intervals.
If you use your vehicle mostly for
short-distance trips, you will need to have
the battery charge checked more
frequently.
When replacing the battery, always use
batteries approved by Mercedes-Benz.
If you do not intend to operate your vehicle
for an extended period of time, consult an
authorized Mercedes-Benz Light Truck
Center about steps you need to observe. Batteries contain materials that can harm
the environment if disposed of improperly.
Large 12-volt storag
e batteries contain
lead. Recycling of batteries is the preferred
method of disposal. Many states require
sellers of batteries to accept old batteries
for recycling.
iMercedes-Benz recommends to have the
battery replaced at an authorized
Mercedes-Benz Light Truck Center.
Warning!G
Observe all safety instructions and precau-
tions when handling automotive batteries.
Risk of explosion.
Fire, open flames and smoking
are prohibited when handling
batteries. Avoid creating sparks.
Battery acid is caustic. Do not
allow it to come into contact
with skin, eyes or clothing.
Wear suitable protective cloth-
ing, especially gloves, apron and
faceguard.
Wear eye protection.
Rinse any acid spills imme-
diately with clear water. Contact
a physician if necessary.
Keep children away.
Follow the instructions in this
Operator’s Manual.
W463.boo Seite 394 Montag, 19 . November 2007 8:41 08

395
Practical hints
Battery
Warning!G
Failure to follow thes
e instructions can
result in severe injury or death.
Observe all safety instructions and precau-
tions when handling automotive batteries
(
page 394).
Never lean over batteries while connecting,
you might get injured.
Battery fluid contains sulfuric acid. Do not
allow this fluid to come in contact with eyes,
skin or clothing. In case it does, immediately
flush affected area with water and seek
medical help if necessary.
A battery will also pr oduce hydrogen gas,
which is flammable and explosive. Keep
flames or sparks away from battery, avoid
improper connection of jumper cables,
smoking, etc.
Warning!G
Jump starting must only be done using the
jump-start terminals located in the engine
compartment (
page 398).
Warning!G
Do not place metal objects on the battery as
this could result in a short circuit.
Use leak-proof battery only to avoid the risk
of acid burns in the event of an accident.
!Never loosen or detach battery terminal
clamps while the engine is running or the
SmartKey is in the starter switch. Otherwise the
alternator and other electronic components
could be severely damaged.
Have the battery checked regularly at an
authorized Mercedes-Benz Light Truck Center.
Refer to Maintenance Booklet for maintenance
intervals or contact an authorized
Mercedes-Benz Light Truck Center for further
information.
W463.boo Seite 395 Montag, 19 . November 2007 8:41 08

396 Practical hints
Battery
Disconnecting, removing, reinstalling
and reconnecting the battery
Disconnecting, removing, reinstalling and
reconnecting the battery is a complicated
and technically demanding procedure that
also requires safety precautions to avoid
the risk of injury. We strongly recommend
that it should be performed by a qualified
technician only. If it is necessary to work
on the battery, contac t a local authorized
Mercedes-Benz Light Truck Center or call
our Customer Assistance Center at
1-800-FOR-MERCedes (1-800-367-6372).
Charging the battery
If the battery is disc harged, the battery can
be charged using the jump-start terminals
located in the engine compartment
(
page 398).
Charge the battery in accordance with
the instructions of the battery charger
manufacturer.
!Never invert the terminal connections!
!The battery, its filler caps and the vent tube
must always be securely installed when the
vehicle is in operation.
Warning!G
Never charge a battery while still installed in
the vehicle unless th e accessory battery
charge unit* approved by Mercedes-Benz is
being used. Gases may escape during charg-
ing and cause explosions that may result in
paint damage, corrosion or personal injury.
An accessory battery ch arge unit* specially
adapted for Mercedes-Benz vehicles and
tested and approved by Mercedes-Benz is
available, permitting the charging of the
battery in its installe d position. Contact an
authorized Mercedes-Benz Light Truck
Center for information and availability.
Charge battery in acco rdance with the sepa-
rate instructions for the accessory battery
charger*.
iWith a discharged battery

you will no longer be able to turn the
SmartKey in the starter switch

the gear selector lever will remain locked in
park position P
W463.boo Seite 396 Montag, 19 . November 2007 8:41 08

397
Practical hints
Jump starting
 Jump starting
If the battery is disc harged, the engine can
be started with jumper cables and the
battery of another vehicle. Observe the
following:

Jump starting should only be performed
using the jump-start terminals located
in the engine compartment
(
page 398).

Jump starting should only be performed
when the engine and catalytic
converter are cold.

Do not start the engine if the battery is
frozen. Let the battery thaw out first.

Only jump start from batteries with the
same voltage rating (12 V). Jump start-
ing with a higher voltage battery could
damage the vehicle’s electrical system,
which will not be covered by the
Mercedes-Benz Limited Warranty.

Only use jumper cables with sufficient
cross-section and insulated terminal
clamps.

Always make sure the jumper cables
are not on or near pulleys, fans, or
other parts that move when an engine
is started or running.
Warning!G
Failure to follow thes e directions will cause
damage to the electr onic components, and
can lead to a battery explosion and severe
injury or death.
Never lean over batteries while connecting
or jump starting, you might get injured.
Battery fluid contains sulfuric acid. Do not
allow this fluid to come in contact with eyes,
skin or clothing. In case it does, immediately
flush affected area with water, and seek
medical help if necessary.
A battery will also pr oduce hydrogen gas,
which is flammable and very explosive. Keep
flames or sparks away from battery, avoid
improper connection of jumper cables,
smoking, etc.
Attempting to jump start a frozen battery
can result in it explod ing, causing personal
injury.
Read all instructions before proceeding.
!Do not tow-start the vehicle.
!Avoid repeated and lengthy starting
attempts.
Do not attempt to start the engine using a
battery quick charge unit.
If the engine does not run after several unsuc-
cessful starting attempts, have it checked at the
nearest authorized Mercedes-Benz Light Truck
Center.
Excessive unburned fuel generated by repeated
failed starting attempts may damage the
catalytic converter.
Make sure the jumper cables do not have loose
or missing insulation.
Make sure the cable clamps do not touch any
other metal part while the other end is still
attached to a battery.
W463.boo Seite 397 Montag, 19 . November 2007 8:41 08

398 Practical hints
Jump starting
Make sure the two vehicles do not
touch.
Apply the parking brake (page 62).
Move the gear selector lever to park
positionP.
Turn off all electrical consumers.
Open the hood (page 267). The jump-start terminals are located on
the driver’s side of the engine compart-
ment.
1 Cover
2 Positive (+) terminal
3 Negative (-) terminal Open cover 1 of the positive terminal
of both vehicles.
Connect positive terminal 2 and the
positive terminal of the charged battery
with the jumper cable. Clamp the cable
to the charged battery first.
Start the engine of the vehicle with the
charged battery and run at idle speed.
Connect negative terminal 3 and the
negative terminal of the charged
battery with the jumper cable. Clamp
the cable to the charged battery first.
Start the engine of the disabled
vehicle.
You can now turn on the electrical con-
sumers. Do not switch on the headlamps
under any circumstances.
Remove the jumper cables first from
the negative terminals on each battery
and then from the positive terminals on
each battery.
You can now switch on the headlamps.
Have the battery checked at the
nearest authorized Mercedes-Benz
Light Truck Center.
Warning!G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety inst ructions and precau-
tions when handling automotive batteries
(
page 394).
!Never invert the terminal connections!
W463.boo Seite 398 Montag, 19 . November 2007 8:41 08

403
Practical hints
Fuses
 Fuses
The electrical fuses in your vehicle serve to
switch off malfunctioning power circuits.
If a fuse is blown, the components and
systems secured by that fuse will stop
operating. If a newly inserted fuse blows again, have
the cause determined and rectified at an
authorized Mercedes-Benz Light Truck
Center.
The following aids are available to help you
replace fuses.

Fuse chart
The fuse chart explains the fuse
allocation and fuse amperages.
The fuse chart is located in the main
fuse box in the passenger compart-
ment (
page 404).

Spare fuses
The spare fuses are located in the main
fuse box in the passenger compart-
ment (
page 404).

Fuse extractor
The fuse extractor is located in the
vehicle tool kit in the rear footwell
(
page 364).The electrical fuses are located in different
fuse boxes:

in the passenger compartment on the
driver’s side (
page 404)

in the front passenger footwell
(
page 404)

in the middle tunnel (page 405)

in the battery box (page 406)
Before replacing fuses:
Apply parking brake (page 62).
Make sure the gear selector lever is set
to park position P (
page 162).
Turn off all electrical consumers.
Turn off the engine (page 64).
Remove the SmartKey from the starter
switch.
Warning!G
Only use fuses approved by Mercedes-Benz
with the specified amperage for the system
in question and do not attempt to repair or
bridge a blown fuse. Using other than
approved fuses or using repaired or bridged
fuses may cause an overload leading to a
fire, and/or cause damage to electrical
components and/or systems. Have the
cause determined and remedied at an
authorized Mercedes-Benz Light Truck
Center.
iA blown fuse must be replaced by an
appropriate spare fuse (recognizable by its color
or the fuse rating given on the fuse) of the
amperage recommended in the fuse chart. Any
Mercedes-Light Truck Center will be glad to
advise you on this subject.
W463.boo Seite 403 Montag, 19 . November 2007 8:41 08