brake light MERCEDES-BENZ GL320 2008 X164 Workshop Manual

519 Practical hints
Flat tire
Flat tire
Preparing the vehicle
Make sure the vehicle level is set to
highway (
page 279).
Park the vehicle in a safe distance from
moving traffic on a hard, flat surface
when possible.
Turn on the hazard warning flasher
(
page 149).
Turn the steering wheel so that the
front wheels are in a straight-ahead
position.
Set the parking brake (page 59).
Set the automatic transmission to park
positionP (
page 191).
Turn off the engine (page 41).
Have any passenger exit the vehicle at
a safe distance from the roadway.
Vehicles with SmartKey: Remove the
SmartKey from the starter switch.
Vehicles with KEYLESS-GO*: Open the
driver’s door (this puts the starter
switch in position0, same as with the
SmartKey removed from the starter
switch). The driver’s door then can be
closed again.
Remove the KEYLESS-GO*
start/stop button from the starter
switch.
Warning!G
The dimensions of the Minispare wheel are
different from those of the road wheels. As
a result, the vehicle handling characteristics
change when driving with a Minispare wheel
mounted. Adapt your driving style accord-
ingly.
The Minispare wheel is for temporary use
only. When driving with a Minispare wheel
mounted, ensure proper tire pressure and
do not exceed a vehicle speed of
50 mph (80 km/h).
Drive to the nearest Mercedes-Benz Light
Truck Center as soon as possible to have the
Minispare wheel replaced with a regular
road wheel.
Never operate the vehicle with more than
one spare wheel mounted.
Do not switch off the ESP
® when a
Minispare wheel is mounted.
Warning!G
Your vehicle is equipped with air suspen-
sion. Do not open or close any doors or the
tailgate while mounting a spare wheel. The
vehicle could rise or lower to a previously se-
lected level. You or others could be injured
as a result.
iOpen door only when conditions are safe to
do so.
164.boo Seite 519 Freitag, 30. März 2007 12:54 12

525 Practical hints
Flat tire
Mounting the new wheel
1Wheel bolt for 18", 19", 20" and 21"
light alloy wheels
2Wheel bolt for Minispare wheel (locat-
ed in vehicle tool kit (
page 490))
Clean contact surfaces of wheel and
wheel hub.
Guide spare wheel onto the alignment
bolt and push it on the wheel hub.
Insert wheel bolts and tighten them
slightly.
Unscrew the alignment bolt, install last
wheel bolt and tighten slightly.
!Wheel bolts2 must be used when mount-
ing the Minispare wheel. The use of any wheel
bolts other than wheel bolts2 for the Minispare
wheel will damage the vehicle’s brakes.
!To avoid paint damage, place wheel flat
against hub and hold it there while installing first
wheel bolt.
Warning!G
Always replace wheel bolts that are
damaged or rusted.
Never apply oil or grease to wheel bolts.
Damaged wheel hub threads should be
repaired immediately. Do not continue to
drive under these circumstances! Contact
an authorized Mercedes-Benz Light Truck
Center or call Roadside Assistance.
Incorrect wheel bolts or improperly tight-
ened wheel bolts can cause the wheel to
come off. This could cause an accident.
Make sure to use the correct wheel bolts.
Warning!G
Only use genuine Mercedes-Benz wheel
bolts. Other wheel bolts may come loose.
Do not tighten the wheel bolts when the
vehicle is raised. Otherwise the vehicle
could fall off the jack.
164.boo Seite 525 Freitag, 30. März 2007 12:54 12

530 Practical hints
Battery
Disconnecting, removing, reinstalling
and reconnecting the battery
Step 1 (Disconnecting)
Set the automatic transmission to
positionP (
page 191).
Firmly depress the parking brake
(
page 67).
Turn off the engine (page 68).
Leave the ignition switched on
(
page 42).
!Never loosen or detach battery terminal
clamps while the engine is running or the
SmartKey is in the starter switch. Otherwise the
alternator and other electronic components
could be severely damaged.
Have the battery checked regularly by an
authorized Mercedes-Benz Light Truck Center.
Contact your authorized Mercedes-Benz Light
Truck Center for further information.
Warning!G
Do not place metal objects on the battery as
this could result in a short circuit.
Use leak-proof battery only to avoid the risk
of acid burns in the event of an accident.
Warning!G
Disconnecting, removing, reinstalling and
reconnecting the battery is a complicated
and technically demanding procedure that
also requires safety precautions to avoid the
risk of injury. We strongly recommend that it
be performed by a qualified technician or an
authorized Mercedes-Benz Light Truck
Center only. Please read the instructions
fully before beginning operation and only
undertake it if you feel fully capable of
performing all of the tasks involved as de-
scribed in these instructions. Observe all
safety instructions and precautions when
handling automotive batteries
(
page 528). Performing the tasks involved
incorrectly can cause damage to the vehicle
and impair the operating safety of the
vehicle, and/or cause severe injury to you
or others.
iWith a disconnected battery you will no
longer be able to turn the SmartKey in the starter
switch and pressing the KEYLESS-GO*
start/stop button will have no effect.
iIf your battery is discharged, the vehicle
must be jump started (
page 536) using the
jump start contacts in the engine compartment,
or an accessory battery charge unit* approved
by Mercedes-Benz must be connected using the
jump start contacts in the engine compartment
(see separate instructions for the accessory bat-
tery charge unit*) before any of the following
steps can be performed. If the battery cannot be
jumped or charged, please contact an
authorized Mercedes-Benz Light Truck Center.
164.boo Seite 530 Freitag, 30. März 2007 12:54 12

537 Practical hints
Jump starting
The jump-start contacts are located in the
engine compartment.
1Negative (-) terminal
2Positive (+) terminal
3Positive terminal cover
Make sure the two vehicles do not
touch.
Turn off all electrical consumers.
Apply parking brake (page 67).
Set automatic transmission to
positionP (
page 191).
Open the hood (page 378).
Remove cover from negative
terminal1.
Flip up cover3 of positive terminal2
in direction of arrow.
1Negative terminal of discharged
battery
2Positive terminal of discharged battery
4Positive terminal of charged battery
5Negative terminal of charged battery
Connect positive terminal2 and4
with the jumper cable. Clamp cable to
charged battery4 first.
Start engine of the vehicle with the
charged battery and run at idle speed.
Connect negative terminals1 and5
of the batteries with the second jumper
cable. Clamp the cable to negative
terminal5 of the charged battery
first.
Start the engine of the disabled vehi-
cle.
You can now turn on the electrical consum-
ers. Do not switch on the headlamps under
any circumstances.
Remove the jumper cables first from
negative terminals1 and5 and then
from positive terminals2 and4.
You can now switch on the headlamps.
Have the battery checked at the near-
est authorized Mercedes-Benz Light
Truck Center.
Warning!G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(
page 528).
!Never invert the terminal connections!
164.boo Seite 537 Freitag, 30. März 2007 12:54 12

543 Practical hints
Fuses
Fuses
The electrical fuses in your vehicle serve to
switch off malfunctioning power circuits.
If a fuse is blown, the components and sys-
tems secured by that fuse will stop operat-
ing.If a newly inserted fuse blows again, have
the cause determined and rectified by an
authorized Mercedes-Benz Light Truck
Center.
A fuse chart explains the fuse allocation
and fuse amperages. It is located in the
cargo compartment with the vehicle tool
kit (
page 490).
The electrical fuses are located in different
fuse boxes:

Fuse box in engine compartment
(
page 544)

Fuse box in cargo compartment
(
page 544)

Fuse box in passenger compartment
(
page 545)Before replacing fuses:
Apply parking brake (page 67).
Make sure the automatic transmission
is set toP (
page 191).
The gear position indicator in the multi-
function display should be on
P.
Turn off all electrical consumers.
Turn off the engine (page 41).
Remove the SmartKey from the starter
switch.
Vehicles with KEYLESS-GO*:
Open the driver’s door (this puts
the starter switch in position0,
same as with the SmartKey re-
moved from the starter switch). The
driver’s door then can be closed
again.
Warning!G
Only use fuses approved by Mercedes-Benz
with the specified amperage for the system
in question and do not attempt to repair or
bridge a blown fuse. Using other than ap-
proved fuses or using repaired or bridged
fuses may cause an overload leading to a
fire, and/or cause damage to electrical
components and/or systems. Have the
cause determined and remedied by an au-
thorized Mercedes-Benz Light Truck Center.
iA blown fuse must be replaced by an appro-
priate spare fuse (recognizable by its color or the
fuse rating given on the fuse) of the amperage
recommended in the fuse chart. Any
Mercedes-Benz Light Truck Center will be glad to
advise you on this subject.
164.boo Seite 543 Freitag, 30. März 2007 12:54 12

564 Technical data
Fuels, coolants, lubricants
Engine oils
Engine oils are specifically tested for their
suitability in our engines and durability for
our service intervals. Therefore, only use
approved engine oils and oil filters
required for vehicles with Maintenance
System. For a listing of approved engine
oils and oil filters, refer to the Factory
Approved Service Products pamphlet
(USA only), or contact an authorized
Mercedes-Benz Light Truck Center.Engine oil additives
Air conditioning refrigerant
R-134a (HFC) refrigerant and special PAG
lubricating oil are used in the air
conditioning system.
Brake fluid
Only brake fluid approved by
Mercedes-Benz is recommended. Any
authorized Mercedes-Benz Light Truck
Center will provide you with additional
information.
!Using engine oils and oil filters of
specification other than those expressly
required for the Maintenance System, or chang-
ing of oil and oil filter at change intervals longer
than those called for by the Maintenance System
will result in engine or emission control system
damage not covered by the Mercedes-Benz
Limited Warranty.
Please follow Maintenance System recommen-
dations for scheduled oil changes. Failure to do
so will result in engine or emission control
system damage not covered by the
Mercedes-Benz Limited Warranty.
!Do not blend oil additives with engine oil.
They may damage the engine.
Damage or malfunctions resulting from blending
oil additives are not covered by the
Mercedes-Benz Limited Warranty.
!Never use R-12 (CFC) or mineral-based
lubricating oil. Otherwise damage to the system
will occur.
Warning!G
During vehicle operation, the boiling point of
the brake fluid is continuously reduced
through the absorption of moisture from the
atmosphere. Under extremely strenuous
operating conditions, this moisture content
can lead to the formation of bubbles in the
system, thus reducing the system’s
efficiency.
Therefore, the brake fluid must be replaced
regularly. Refer to your vehicle’s
Maintenance Booklet for replacement inter-
val.
164.boo Seite 564 Freitag, 30. März 2007 12:54 12

580 Index
Headlamps
Automatic headlamp mode 144
Bi-Xenon* 477, 508
Cleaning lenses 429
Cleaning system* 208, 383
Halogen 507
High beam see High beam flasher
High beam see High beam headlamps
Light sensor, Messages in the
multifunction display 477
Low beam see Low beam headlamps
Manual headlamp mode 144
Messages in the multifunction
display 477, 478, 479, 480, 481,
482
Replacing bulbs 504, 505
Switch 61, 143
Heated seats see Seat heating*
Heated steering wheel* 327
Height adjustment
Vehicle level control (Vehicles with Air
suspension program) 281
Vehicle level control (Vehicles with
enhanced Off-road Package*) 283High beam flasher 61, 147
High beam headlamps
Indicator lamp 29
Messages in the multifunction
display 478
Replacing bulbs 505, 507, 508
Switching on 61, 147
High mounted brake lamp 505
Hill start assist system 196
Hinged quarter windows* see
Power windows
Hood 378
Messages in the multifunction
display 474
Opening 378
Hooks
Loading 304
Horn 25
HVAC see Climate control or
automatic climate control (3-zone)*
Hydroplaning 352I
Identification labels see Labels
Ignition 42, 44, 57
Immobilizer 109
Indicator lamps see Lamps, Indicator and
warning
Infant and child restraint systems see
Children in the vehicle
Inflation pressure see Tires,
Inflation pressures
Information button see Tele Aid
Infrared reflecting windshield* 344
Inside door handle 120
Instrument cluster 26, 28, 152
Illumination brightness 153
Lamps 436
Messages in display see Multifunction
display messages
Multifunction display 155
Outside temperature indicator 153
Selecting language 172
Instrument lighting see Instrument cluster,
Illumination brightness
Instrument panel see Instrument cluster
164.boo Seite 580 Freitag, 30. März 2007 12:54 12

582 Index
Kickdown 196
Kilopascal 416
L
Labels 550
Certification 550
Emission control information 551
Engine number 551
Paintwork code 550
Vehicle Identification Number
(VIN) 550
Lamp sensor see Light sensor
Lamps, exterior 505
Front 505
Light sensor, Messages in the
multifunction display 477
Messages in display 477
Messages in the multifunction
display 477, 479, 481
Rear 505
Switch 143Lamps, indicator and warning
ABS 27, 436
Adaptive Damping System
(ADS)* 279
Alarm system 110
Battery (SmartKey with
KEYLESS-GO*) 119
Battery (SmartKey) 114
Brakes 27, 437, 438
Center console 31, 32, 447
CHECK ENGINE 29, 439, 440
Differential locks* 205
Distance warning lamp* 263
Downhill Speed Regulation 274
Engine diagnostics 29, 439, 440
ESP
®27, 441
Fog lamps, Front/rear 143
Front passenger front air bag off 31,
32, 80
Fuel reserve 29, 446
High beam headlamps 29
Instrument cluster 26, 28, 436, 437,
438, 439, 440, 441, 442, 443, 444,
446
Off-road driving program 278
Parktronic* 290Preglow indicator, Diesel engine 29
Seat belt telltale 29, 89, 442
Seat belts 443
Seat heating* 138
Seat ventilation* 140
SRS 29, 74, 89, 446
Turn signals 27
Vehicle level control 281, 283
Language, Setting 172
LATCH-type child seat anchors see
Children in the vehicle
Layout of poly-V-belt drive
(GL 320 CDI) 552
Layout of poly-V-belt drive
(GL 450, GL 550) 552
Leather upholstery*, Cleaning and care
of 434
Lever for cruise control 255
License plate lamps 514
Messages in the multifunction
display 479
Replacing bulbs 505, 514
Light alloy wheels, Cleaning 432
Light sensor
Messages in the multifunction
display 477
164.boo Seite 582 Freitag, 30. März 2007 12:54 12

585 Index
Off-road - 4-ETS 108
Off-road - ABS 102
Off-road - ESP
®106
Off-road driving
Checklist 357, 363
Crossing obstacles 361
Driving instructions for off-road
driving 355
Driving through water 360
Returning 363
Rules 356
Special driving features 356
Steep terrain 358
Off-road driving program (Vehicles without
enhanced off-road package*) 277
Oil level see Engine oil, Checking level
One-touch gearshifting 199
Operating safety 17
Operator’s Manual 10
Ornamental moldings, Cleaning 429
Outside temperature see Displays
Overdue maintenance service term 423
Overhead control panel 34
Oxidation catalyst (diesel engine) 371P
Paintwork code 550
Paintwork, Cleaning 426
Panic alarm 100
Panorama roof, Rear 212
Parcel net
Front passenger footwell 319
Front seat backrests 319
Parking 67, 350
On hills 67
Over things that burn, Potential
consequences 67, 371
Parking brake 59, 67
Lamps, Indicator and warning 437
Messages in the multifunction
display 468
Releasing 59
Parking lamps 505
Messages in the multifunction
display 480
Replacing bulbs 509
Parking position*
Exterior rear view mirrors 182, 209Parktronic* 31, 32, 288
Cleaning system sensors 430
Minimum distance 290
Range 289
Switching on/off 291
System malfunction 292
System sensors 289
System sensors, Cleaning 430
Warning indicators 25, 290
Parts service 548
PASS AIR BAG OFF indicator lamp see
Front passenger front air bag off
indicator lamp
Passenger compartment 370
Fuse box 545
Interior lighting 149
Interior rear view mirror 34
Parcel net in front passenger
footwell 319
Passenger safety see Occupant safety
Pedals 347
Phone see Telephone*
164.boo Seite 585 Freitag, 30. März 2007 12:54 12