roof MERCEDES-BENZ GL320CDI 2007 X164 Owner's Guide

253 Controls in detail
Power tilt/sliding sunroof*
Power tilt/sliding sunroof*
Opening and closing
Warning!G
When closing the tilt/sliding sunroof, make
sure that there is no danger of anyone being
harmed by the closing procedure.
If the tilt/sliding sunroof encounters an ob-
struction that blocks its path in a circum-
stance where you are closing the tilt/sliding
sunroof by moving the tilt/sliding sunroof
switch past the resistance point, or by
pressing and holding button‹ on the
SmartKey, by pressing and holding the lock
button (vehicles with KEYLESS-GO*) on the
door handle, the automatic reversal function
will not operate.
The opening/closing procedure of the
tilt/sliding sunroof can be immediately halt-
ed by releasing the switch or, if the switch
was moved past the resistance point and re-
leased, by moving the switch in any direc-
tion.
The tilt/sliding sunroof is made out of glass.
In the event of an accident, the glass may
shatter. This may result in an opening in the
roof.
In a vehicle rollover, occupants not wearing
their seat belts or not wearing them properly
may be thrown out of the opening. Such an
opening also presents a potential for injury
for occupants wearing their seat belts prop-
erly as entire body parts or portions of them
may protrude from the passenger compart-
ment.
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock your vehicle. Do not leave children un-
attended in the vehicle, or with access to an
unlocked vehicle. A child’s unsupervised
access to a vehicle could result in an
accident and/or serious personal injury.!To avoid damaging the seals, do not trans-
port any objects with sharp edges which can
stick out of the tilt/sliding sunroof.
Do not open the tilt/sliding sunroof if there is
snow or ice on the roof, as this could result in
malfunctions.
The tilt/sliding sunroof can be opened or closed
manually should an electrical malfunction occur
(
page 503).
!Please keep in mind that weather conditions
can sometimes change rapidly. Make sure to
close the tilt/sliding sunroof when leaving the
vehicle. If water enters the vehicle interior,
vehicle electronics could be damaged which is
not covered by the Mercedes-Benz Limited
Warranty.
iWhen the tilt/sliding sunroof is open, reso-
nance noises may result in addition to the usual
wind noises. They are caused by minimal pres-
sure changes in the passenger compartment. To
reduce or eliminate these noises, change the po-
sition of the tilt/sliding sunroof or open a side
window slightly.

254 Controls in detail
Power tilt/sliding sunroof*
The tilt/sliding sunroof is opened and
closed electrically. The switch for the
tilt/sliding sunroof is located on the
overhead control panel.
Sunroof switch
1Push back to slide sunroof open
2Push forward to slide sunroof closed
3Push up to raise sunroof at rear
4Pull down to lower sunroof at rear
With the sunroof closed or tilted open, a
screen can be slid into the roof opening to
guard against sun rays. When sliding the
sunroof open, the screen will also retract.
Switch on the ignition (page 42).
Opening and closing
To open, close, raise, or lower the
tilt/sliding sunroof, move the sunroof
switch to the resistance point in the
required direction of arrows1to4
(
page 254).
Release the sunroof switch when the
tilt/sliding sunroof has reached the de-
sired position.
iYou can also open or close the tilt/sliding
sunroof using the SmartKey or the
KEYLESS-GO* function, see “Summer opening
feature” (
page 251) and see “Convenience
closing feature” (
page 252).
iDepending on the current position, the
tilt/sliding sunroof may also open or close when
the air recirculation button: on the control
panel of the climate control (
page 218) or
automatic climate control* (
page 232) is
pressed and held.

255 Controls in detail
Power tilt/sliding sunroof*
Fully opening (Express-open) and
closing (Express-close)
To fully open or close the tilt/sliding
sunroof, move the sunroof switch past
the resistance point in the required
direction of arrows1to2
(
page 254) and release.
The tilt/sliding sunroof opens or closes
completely.
Stopping the power tilt/sliding sunroof
during Express-open
Move the sunroof switch in any direc-
tion.
The movement of the tilt/sliding sun-
roof stops.
Synchronizing
The tilt/sliding sunroof must be
synchronized

after the battery has been
disconnected or discharged

after the tilt/sliding sunroof has been
closed manually (
page 503)

after a malfunction

if the tilt/sliding sunroof does not open
smoothly
Remove the fuse for the tilt/sliding
sunroof from the fuse box
(
page 544).
iIf the movement of the tilt/sliding sunroof is
blocked during the closing procedure, the
tilt/sliding sunroof will stop and reopen slightly.
Warning!G
If the tilt/sliding sunroof encounters an ob-
struction that blocks its path in a circum-
stance where you are closing the tilt/sliding
sunroof by moving the tilt/sliding sunroof
switch past the resistance point, or by
pressing and holding button‹ on the
SmartKey, by pressing and holding the lock
button (vehicles with KEYLESS-GO*) on the
door handle, the automatic reversal function
will not operate.
The opening/closing procedure of the
tilt/sliding sunroof can be immediately halt-
ed by releasing the switch or, if the switch
was moved past the resistance point and re-
leased, by moving the switch in any direc-
tion.
iFor information on which fuse box contains
the fuse for the power tilt/sliding sunroof, see
the fuse chart provided with the vehicle tool kit
(
page 495).

256 Controls in detail
Power tilt/sliding sunroof*
Reinsert the fuse in the main box.
Switch on the ignition (page 42).
Press and hold the sunroof switch in
the direction of arrow3 (
page 254)
until the tilt/sliding sunroof is fully
raised at the rear.
Hold the sunroof switch in the direction
of arrow3 for approximately
1 second.
Open the tilt/sliding sunroof using the
Express-open feature (
page 255).
If the tilt/sliding sunroof opens
completely, it is synchronized.
If the tilt/sliding sunroof does not open
completely:
Repeat the above steps.


292 Controls in detail
Driving systems
Front sensors
Rear sensors
Minimum distance
If the system detects an obstacle in this
range, all the distance warning segments
illuminate and you hear a warning signal. If
the obstacle is closer than the minimum
distance, the actual distance may no
longer be indicated by the system.Warning indicators
Visual signals indicate to the driver the rel-
ative distance between the sensors and an
obstacle. The warning indicator for the
front area is located above the center air
vents in the dashboard. The warning indi-
cator for the rear area is located in the rear
passenger compartment under the roof.
Front area warning indicator
1Left side of the vehicle
2Right side of the vehicle
3Readiness indicatorsEach warning indicator is divided into five
yellow and two red distance segments for
either side of the vehicle. The Parktronic
system is operational when the readiness
indicators3 are illuminated.
The current transmission position deter-
mines which warning indicator will be acti-
vated.
Centerapprox. 40 in (100 cm)
Cornersapprox. 24 in (60 cm)
Centerapprox. 48 in (120 cm)
Cornersapprox. 32 in (80 cm)
Centerapprox. 8 in (20 cm)
Cornersapprox. 6 in (15 cm)
Automatic trans-
mission positionWarning indicator
DFront area activated
R or NFront and rear area
activated
PNeither activated

297 Controls in detail
Loading
Loading
Carriers*
Roof rails
Basic cross bars*
The maximum roof load (
page 559) of
any add-on roof equipment is reduced by
the unladen weight of the basic cross bars
(13.7 Ibs/6.2 kg).
Four keys and an Allen wrench required for
installing and removing are included with
the basic cross bars.
Warning!G
Only use carriers* when the basic cross
bars have been completely mounted. The
left and right roof rails are only stabilized by
means of the basic cross bars mounted.
Follow the manufacturer’s installation
instructions. Otherwise, an improperly at-
tached roof rack system or its load could be-
come detached from the vehicle.
Do not exceed the maximum roof load of
198 lb (90 kg).
Take into consideration that when the roof is
loaded, the handling characteristics are dif-
ferent from those when operating the vehi-
cles without a roof loaded.
!Load the carriers* in such a way that the
vehicle cannot be damaged while driving.
Make sure

the tailgate can be completely opened

the tilt/sliding sunroof can be completely
raised at the rear
iThe following accessories are available for
your Mercedes-Benz:

Roof Cargo Container – Small, Medium, or
Large

Ski and Snowboard Carrier – Standard

Ski and Snowboard Carrier – Deluxe (Only in
connection with corresponding adapter.)
For more information on Mercedes-Benz acces-
sories, contact your authorized Mercedes-Benz
Light Truck Center.
iThe keys and the Allen wrench are stored
with the vehicle tool kit under the cargo compart-
ment floor (
page 495).

298 Controls in detail
Loading
Installing the basic cross bars
iSpare parts are available as Mercedes-Benz
accessories. Contact your authorized
Mercedes-Benz Light Truck Center.
Warning!G
Please follow these installation instructions
carefully. Caution should be exercised to
avoid damage to the vehicle while installing
the basic cross bars. Also, be careful not to
injure yourself or others while installing and
adjusting the basic cross bars or loading
items on them.
Each individual step of the installation in-
structions, the warning notices, the general
safety precautions and the instructions for
use must be followed exactly. If the basic
cross bars are not mounted correctly, they
and the objects attached to them could
come loose from your vehicle and cause an
accident, thereby injuring you and other per-
sons and/or causing damage to property,
including damage to your vehicle.
Warning!G
Every time the basic cross bars are mount-
ed, before you set off on a journey and peri-
odically during longer journeys, check all the
screws on the bars to make sure that they
are secure, and tighten them if necessary.
Repeat these checks at regular intervals as
road-surface conditions dictate, and at least
after every 1500 miles (2500 km) of contin-
uous use.
Otherwise, the basic cross bars, mounted
accessories and the objects attached to
them could come loose from the vehicle
causing an accident, thereby injuring you
and other persons and/or causing damage
to property, including damage to your vehi-
cle.
Do not use lubricant on the screws of the
basic cross bars. The screws could work
loose and the basic cross bars could be-
come detached from your vehicle, together
with the objects attached to them causing
an accident, thereby injuring you and other
persons and/or causing damage to proper-
ty, including damage to your vehicle.
Warning!G
Only install the basic cross bars at the exact
locations designated on the roof rails. The
designated locations for the front basic
cross bars are between the markings en-
graved on the inside of the roof rails
(
page 300). The designated locations for
the rear basic cross bars are between the
gaps on the roof rails (
page 300).

299 Controls in detail
Loading
Otherwise, the basic cross bars
(
page 300), mounted accessories and the
objects attached to them could come loose
from the vehicle causing an accident, there-
by injuring you and other persons and/or
causing damage to property, including dam-
age to your vehicle.
Warning!G
A roof load creates a greater surface area
exposed to the wind and causes the vehicle
to have a higher center of gravity, thereby
changing the vehicle’s driving characteris-
tics. Accordingly, the additional weight on
the roof of the vehicle can have a detrimen-
tal effect on braking, cornering and acceler-
ation.
Never exceed the maximum permissible
roof load or the maximum permissible vehi-
cle weight, even when accessories for the
basic cross bars (e.g. ski racks, bicycle
racks, etc.) are being used. Overloading the
vehicle could result in an accident. When
calculating the weight placed on the roof
please make sure to add the weight of the
basic cross, accessory racks and the load
carried together.
Always adapt your driving style to the road,
traffic and weather conditions, and drive
with added caution when the roof is loaded.
Always drive with extreme care when the
roof rack is loaded. Take into consideration
that when the roof rack is loaded, the han-
dling characteristics are different from
those when operating the vehicles without a
roof rack loaded.Warning!G
Do not use accessories which have not been
approved by Mercedes-Benz for use in con-
junction with these basic cross bars. If
non-approved accessories are used, these
accessories and/or the objects attached to
them could come loose from the vehicle,
thereby injuring you and other persons
and/or causing damage to property, includ-
ing damage to your vehicle.
!Have a second person assist you when
installing the basic cross bars. The vehicle could
otherwise be damaged.
!Objects attached to the basic cross bar
system’s accessories must not be allowed to
restrict the movement of the tilt/sliding sunroof.
The tilt/sliding sunroof could otherwise be dam-
aged when it is raised.

300 Controls in detail
Loading
1Key
2Cover cap
3Sticker FRONT (or REAR)
4Screw for clamping claw
5Clamping claw
The front and rear basic cross bars are of
different lengths. Please pay close atten-
tion to stickers3 FRONT and REAR on the
basic cross bars.
Unlock cover cap2 with key1.
Remove cover cap2.
Sticker3 indicating the location,
FRONT or REAR, becomes visible.
Turn screw4 counterclockwise with
the included Allen wrench until
clamping claw5 is wide open.
6Front basic cross bar
7Rear basic cross bar
8Gaps
9Markings
aRoof rails
Place front basic cross bar6 between
markings9 on roof railsa.4Screw for clamping claw
5Clamping claw
aRoof rail
Make sure clamping claw5 lies flush
against the inside of roof raila as
shown in the illustration.
If necessary, adjust clamping width of
basic cross bars (
page 301).
Slightly tighten screw4 on both sides
by turning it clockwise.
iMarkings9 are located on the inside of
each roof rail, indicated by the white lines in the
illustration.

301 Controls in detail
Loading
Place rear basic cross bar7 on roof
railsa i n s u c h a w a y t h a t t h e c l a m p i n g
claws reach into gaps8 (
page 300)
on the roof rails.
Make sure clamping claw5 lies flush
against the inside of roof raila as
shown in the illustration (
page 300).
If necessary, adjust clamping width of
basic cross bars (
page 301).
Slightly tighten screw4 on both sides
by turning it clockwise.
On the front and rear basic cross bars
tighten screws4. Observe a
tightening torque of 4 lb-ft (6 Nm).
Attach cover caps (page 300) and
lock them.
Store key and Allen wrench back into
the storage well (
page 495).
Adjusting the clamping widths of the
basic cross barsThe clamping widths of the basic cross
bars are factory set for your vehicle. These
clamping widths are solely intended for the
designated positions.
Only install the basic cross bars at the des-
ignated locations and pay attention to the
stickers3 FRONT and REAR
(
page 300).
4Screw for clamping claw
5Clamping claw
bScrews for adjusting clamping width
(2 in total for each side)
cCover strip
Warning!G
Have the tightening torque checked after
mounting the basic cross bars. The screws
could come loose if they are not tightened to
a torque of 4 lb-ft (6 Nm).
Warning!G
Only install the basic cross bars at the exact
locations designated on the roof rails. The
designated locations for the front basic
cross bars are between the markings en-
graved on the inside of the roof rails
(
page 300). The designated locations for
the rear basic cross bars are between the
gaps on the roof rails (
page 300).
Otherwise, the basic cross bars
(
page 300), mounted accessories and the
objects attached to them could come loose
from the vehicle causing an accident, there-
by injuring you and other persons and/or
causing damage to property, including dam-
age to your vehicle.