garage door opener MERCEDES-BENZ GL450 2008 X164 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2008, Model line: GL450, Model: MERCEDES-BENZ GL450 2008 X164Pages: 601
Page 7 of 601
Contents
Power tilt/sliding sunroof* ................ 251
Opening and closing ..................... 251
Synchronizing ............................... 253
Driving systems ................................. 255
Cruise control............................... 255
Distronic* (Canada only) .............. 260
Distance warning function*
(Canada only) ............................... 272
Downhill Speed Regulation
(DSR) ............................................ 273
Off-road driving program
(Vehicles without
enhanced off-road package*) ....... 277
Air suspension program ............... 278
Adaptive Damping System
(ADS)* .......................................... 278
Vehicle level control ..................... 279
Parktronic system* ...................... 288
Rear view camera* ....................... 293Loading .............................................. 295
Carriers* ...................................... 295
Loading instructions..................... 301
Cargo tie-down rings .................... 302
Hooks........................................... 304
Expanding cargo compartment .... 304
Cargo compartment cover blind... 310
Cargo net* ................................... 312
Useful features .................................. 315
Storage compartments ................ 315
Parcel nets ................................... 319
Cup holders.................................. 320
Ashtrays ....................................... 321
Cigarette lighter ........................... 323
Power outlets ............................... 324
Floormats ..................................... 325
Seat cover under third-row seats . 326
Heated steering wheel* ............... 327
Telephone* .................................. 328
Tele Aid ........................................ 331
Garage door opener ..................... 338
Compass ...................................... 344
Infrared reflecting windshield* ..... 344
Operation......................................... 345
The first 1000 miles (1500 km) ......... 346
Driving instructions ........................... 347
Drive sensibly – save fuel............. 347
Drinking and driving ..................... 347
Pedals .......................................... 347
Power assistance ......................... 348
Brakes.......................................... 348
Driving off .................................... 350
Parking......................................... 350
Tires ............................................. 351
Hydroplaning................................ 352
Tire traction ................................. 352
Tire speed rating .......................... 353
Winter driving instructions ........... 353
Standing water............................. 355
Off-road driving ............................ 355
Trailer towing ............................... 364
Passenger compartment .............. 370
Driving abroad ............................. 370
Control and operation of radio
transmitters ................................. 370
Catalytic converter
(gasoline engine).......................... 371
164.boo Seite 6 Freitag, 30. März 2007 12:54 12
Page 35 of 601
34 At a glance
Overhead control panel
ItemPage
1Left reading lamp switch149
2Rear interior lighting switch149
3Automatic interior lighting
switch149
4Front interior lighting switch149
5Right reading lamp switch149
6Front right interior lamp149
7Power tilt/sliding sunroof*
switch251
8Tele Aid (emergency call
system) button334
9Interior rear view mirror208
aFront right reading lamp149
ItemPage
bFront left reading lamp149
cGarage door opener339
dVehicles without
telephone* installed:
Hands-free microphone for
Tele Aid (emergency call
system)331
eVehicles with telephone*
installed:
Hands-free microphone for
Tele Aid (emergency call
system) and telephone*331
fFront left interior lamp149
164.boo Seite 34 Freitag, 30. März 2007 12:54 12
Page 339 of 601
338 Controls in detail
Useful features
As an alternative, you may unlock the vehi-
cle via Internet using the ID and password
sent to you shortly after the completion of
your acquaintance call.
The Response Center will then unlock your
vehicle with the remote door unlocking
feature.Stolen Vehicle Recovery services
In the event your vehicle was stolen:
Report the incident to the police.
The police will issue a numbered
incident report.
Pass this number on to the
Mercedes-Benz Response Center along
with your password issued to you when
you subscribed to the service.
The Response Center will then attempt
to covertly contact the vehicle’s
Tele Aid system. Once the vehicle is
located, the Response Center will
contact the local law enforcement and
you. The vehicle’s location will only be
provided to law enforcement.
If you have any questions, please call the
Response Center at 1-800-756-9018 (in
the USA) or 1-888-923-8367 (in Canada).
Garage door opener
The integrated remote control is capable of
operating up to three separately controlled
devices. It provides a convenient way to re-
place up to three hand-held remote con-
trols used to operate devices such as
garage door openers, gate openers, or oth-
er devices compatible with HomeLink
® or
some other systems.
Before the integrated remote control can
be used, it must be programmed to the ga-
rage door opener, gate operator or other
device you wish to operate. See the follow-
ing instructions for programming informa-
tion.iThe remote door unlock feature is available
if the relevant cellular phone network is avail-
able.
The SOS button will flash and the message
Connecting Call will appear in the multifunc-
tion display to indicate receipt of the door unlock
command.
Once the vehicle is unlocked, a Response Center
specialist may attempt to establish voice contact
with the vehicle occupants.
If the tailgate recessed handle was pulled for
m o r e t h a n 2 0 s e c o n d s b e f o r e d o o r u n l o c k a u t h o -
rization was received by the Response Center,
you must wait 15 minutes before pulling the tail-
gate recessed handle again.
iWhen the anti-theft alarm stays on for more
than 30 seconds, a call is initiated automatically
to the Response Center. See anti-theft alarm
system (
page 109).
164.boo Seite 338 Freitag, 30. März 2007 12:54 12
Page 340 of 601
339 Controls in detail
Useful features
Interior rear view mirror with integrated
remote control
1Indicator lamp
2 3 4Signal transmitter button
Needed for programming (not part of vehi-
cle equipment):
5Hand-held remote control of ga-
rage door opener, gate operator
or other device
6Hand-held remote control but-
tonProgramming the integrated remote
control
Step 1:
Switch on the ignition (page 42).
Warning!G
Before programming the integrated remote
control to a garage door opener or gate
operator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage. When programming
a garage door opener, the door moves up or
down. When programming a gate operator,
the gate opens or closes.
Do not use the integrated remote control
with any garage door opener that lacks
safety stop and reverse features as required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982).
A garage door that cannot detect an object
– signaling the door to stop and reverse –
does not meet current U.S. federal safety
standards.
When programming a garage door opener,
park the vehicle outside the garage.
Do not run the engine while programming
the integrated remote control. Inhalation of
exhaust gas is hazardous to your health.
All exhaust gas contains carbon monoxide
(CO), and inhaling it can cause unconscious-
ness and possible death.
164.boo Seite 339 Freitag, 30. März 2007 12:54 12
Page 341 of 601
340 Controls in detail
Useful features
Step 2:
If you have previously programmed a
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when indicator lamp1
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory.
If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and be-
gin directly with step 3.Step 3:Hold end of the hand-held remote
control5 of the device you wish to
train approximately 2 to 5 in
(5 to 12 cm) away from the signal
transmitter button (2, 3 or4) to be
programmed, while keeping the indica-
tor lamp1 in view.
Step 4:
Using both hands, simultaneously
press hand-held remote control
button6 and the desired signal trans-
mitter button (2, 3 or4). Do not
release the buttons until step 5 is com-
pleted.
Indicator lamp1 will flash, first slowly
and then rapidly.Step 5:
After indicator lamp1 changes from a
slow to a rapidly flashing light, release
the hand-held remote control button
and the signal transmitter button.
Step 6:
Press and hold the just-trained signal
transmitter button (2, 3 or4) and
observe indicator lamp1.
If indicator lamp1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button (2, 3 or4) is pressed and re-
leased.
iIndicator lamp1 flashes immediately the
first time the signal transmitter button is
programmed. If this button has already been
programmed, the indicator lamp will only start
flashing after 20 seconds.
iIf indicator lamp1 flashes rapidly for about
2 seconds and then turns to a constant light,
continue with programming steps 8 through 12
as your garage door opener may be equipped
with the “rolling code” feature.
164.boo Seite 340 Freitag, 30. März 2007 12:54 12
Page 342 of 601
341 Controls in detail
Useful features
Step 7:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
Rolling code programming
To train a garage door opener (or other
rolling code devices) with the rolling code
feature, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
Step 8:
Locate “training” button on the garage
door opener motor head unit.
Exact location and color of the button
may vary by garage door opener brand.
Depending on manufacturer, the
“training” button may also be referred
to as “learn” or “smart” button. If there
is difficulty locating the transmitting
button, refer to the garage door opener
Operator’s Manual.Step 9:
Press the “training” button on the ga-
rage door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the follow-
ing two steps.
Step 10:
Return to the vehicle and firmly press,
hold for 2 seconds and release the pro-
grammed signal transmitter button
(2, 3 or4).
Step 11:
Press, hold for 2 seconds and release
same signal transmitter button a sec-
ond time to complete the training pro-
cess.Step 12:
Confirm the garage door operation by
pressing the programmed signal trans-
mitter button (2, 3 or4).
Step 13:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the
integrated signal transmitter to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:
iSome garage door openers (or other rolling
code equipped devices) may require you to
press, hold for 2 seconds and release the same
signal transmitter button a third time to
complete the training process.
164.boo Seite 341 Freitag, 30. März 2007 12:54 12
Page 344 of 601
343 Controls in detail
Useful features
Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:
Check the frequency of hand-held
remote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 280-390 MHz.
Put a new battery in hand-held remote
control5. This will increase the likeli-
hood of the hand-held remote control
sending a faster and more accurate sig-
nal to the integrated remote control.
While performing step 3, hold
hand-held remote control5 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming. Attempt varying
angles at the distance of 2 to 5 in
(5 to 12 cm) away or the same angle at
varying distances.
If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.
Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.
iCertain types of garage door openers are in-
compatible with the integrated remote control. If
you should experience further difficulties with
programming the integrated remote control,
contact an authorized Mercedes-Benz Light
Truck Center, or call Mercedes-Benz Customer
Assistance Center (in the USA only) at
1-800-FOR-MERCedes, or Customer Service (in
Canada) at 1-800-387-0100.
iUSA only:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interfer-
ence, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
iCanada only:
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation of the device.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
164.boo Seite 343 Freitag, 30. März 2007 12:54 12
Page 580 of 601
579 Index
Fuel consumption statistics
Since last reset 185
Since start 184
Fuel filler flap 374
Locking/unlocking 374
Opening 374
Opening in an emergency 497
Fuel tank
Capacity 563
Filler flap 374
Fuels, coolants, lubricants etc. 562
Fuses 543
Fuse box in cargo compartment 544
Fuse box in engine compartment 544
Fuse box in passenger
compartment 545
Fuse chart 490
Replacing 543G
Garage door opener 338
Gasoline see Fuel
GAWR 416
Gear range
Automatic transmission 189, 197
Limiting 197
Shifting into optimal 199
Gear selector lever 25, 56, 189
Cleaning 433
Gearshift pattern for automatic
transmission 189
Messages in the multifunction
display 459
Position indicator 192, 197
Transmission position 192
Global locking/unlocking see Key,
SmartKey
Glove box 315
Good visibility 208Gross Axle Weight Rating see GAWR
Gross Trailer Weight see GTW
Gross Vehicle Weight Rating see GVWR
Gross Vehicle Weight see GVW
GTW 416
GVW 416
GVWR 416
H
Halogen headlamp see Headlamps
Hands-free microphone 34
Hard plastic trim items, cleaning 433
Hazard warning flasher 149
Head restraints 46, 133
Active head restraint 90, 133
Front seats, Adjusting 46
Rear seats 91
Rear seats, Adjusting 135
Rear seats, Removing and
installing 136
Headlamp aim
Adjusting 514
Headlamp cleaning system* 208, 383
Reservoir capacity 563
Headlamp shut-off delay see Delayed
shut-off, Exterior lamps
164.boo Seite 579 Freitag, 30. März 2007 12:54 12