wipers MERCEDES-BENZ GL550 2008 X164 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2008, Model line: GL550, Model: MERCEDES-BENZ GL550 2008 X164Pages: 601
Page 4 of 601
Contents
Introduction.......................................... 9
Product information ................................ 9
Operator’s Manual ............................... 10
Service and warranty information .. 10
Important notice for California
retail buyers and lessees of
Mercedes-Benz automobiles .......... 11
Maintenance .................................. 12
Roadside Assistance ...................... 12
Change of address or ownership.... 13
Operating your vehicle
outside the USA or Canada ............ 13
Where to find it .................................... 15
Symbols ............................................... 16
Operating safety .................................. 17
Proper use of the vehicle ............... 17
Problems with your vehicle .................. 18
Reporting safety defects...................... 19
Reporting safety defects ................ 19
Vehicle data recording ......................... 20
Information regarding electronic
recording devices ........................... 20At a glance.......................................... 21
Exterior view ......................................... 22
Cockpit ................................................. 24
Instrument cluster ................................ 26
Instrument cluster ................................ 28
Multifunction steering wheel ................ 30
Center console ..................................... 31
Upper part (Vehicles without
enhanced off-road package*) ......... 31
Upper part (Vehicles with
enhanced off-road package*) ......... 32
Lower part ...................................... 33
Overhead control panel ........................ 34
Door control panel................................ 35
Storage compartments ......................... 36Getting started................................... 39
Unlocking ............................................. 40
Unlocking with the SmartKey ......... 40
Unlocking with KEYLESS-GO*......... 41
Starter switch positions .................. 41
Adjusting .............................................. 45
Seats .............................................. 45
Steering wheel ................................ 48
Mirrors ............................................ 51
Driving .................................................. 53
Fastening the seat belts ................. 53
Starting the engine ......................... 56
Parking brake ................................. 59
Driving off ....................................... 60
Switching on headlamps ................. 61
Turn signals .................................... 62
Windshield wipers ........................... 62
Rear window wiper/washer ............ 64
Problems while driving.................... 65
Parking and locking .............................. 67
Parking brake ................................. 67
Switching off headlamps................. 68
Turning off the engine..................... 68
Releasing seat belts........................ 70
Locking ........................................... 70
164.boo Seite 3 Freitag, 30. März 2007 12:54 12
Page 24 of 601
23 At a glance
Exterior view
ItemPage
1Tailgate122
Power tailgate*123
Cargo compartment
Loading instructions301
Cargo tie-down rings302
Hooks304
Expanding304
Cover blind310
Cargo net*312
Vehicle tool kit490
Spare wheel494
2Rear window defroster212
3Rear lamps505
4Fuel filler flap374
Refueling374
Fuel375,
565
ItemPage
5Exterior rear view mirrors
Adjusting51
Auto-dimming rear view
mirrors*208
Power folding*209
6Towing eye bolt
Installing towing eye bolt540
7Tires and wheels384,
555
Checking tire inflation
pressure395
General information384
Flat tire519
Spare wheel494
8Hood378
Opening378
Engine oil380
Coolant381
ItemPage
9Windshield wipers62
Wiper blades, replacing516
Wiper blades, cleaning431
aWindshield
Cleaning with wiper fluid64
Cleaning431
bRoof rails295
Carriers*296
cPower tilt/sliding sunroof*251
dDoors
Locking and unlocking112
Opening120
Unlocking/locking in an
emergency496
eFront lamps505
fHeadlamp cleaning system*208
164.boo Seite 23 Freitag, 30. März 2007 12:54 12
Page 26 of 601
25 At a glance
Cockpit
ItemPage
1Cruise control lever256
2Instrument cluster26
3Multifunction steering
wheel30
4Horn
5Steering wheel gearshift
buttons198
6Gear selector lever for
automatic transmission56
7Front Parktronic* warning
indicators290
8Overhead control panel34
9Glove box release
Glove box lock315
316
ItemPage
aGlove box315
CD changer315
AUX-socket315
bPower outlet324
cCenter console31
dStarter switch42
eSteering wheel adjustment,
manual49
fHood lock release378
gParking brake release59
hParking brake pedal67
jPower tailgate switch*124
ItemPage
kDoor control panel35
lExterior lamp switch61
143
mSteering wheel adjustment,
electrical*
Heated steering wheel*50
327
nCombination switch
High beam
Turn signals
Windshield wipers
Rear window wiper
147
61
62
62
64
164.boo Seite 25 Freitag, 30. März 2007 12:54 12
Page 63 of 601
62 Getting started
Driving
Turn signals
The combination switch is located on the
left of the steering column.
Combination switch
1Turn signals, right
2Turn signals, left
Press the combination switch in
direction of arrow1 or2.
The corresponding turn signal indicator
lampL orK in the instrument
cluster flashes (
page 26).The combination switch resets automati-
cally after major steering wheel move-
ment.
Windshield wipers
The combination switch is located on the
left of the steering column.
Combination switch
1Single wipe
Wiping with windshield washer fluid
2Switching on windshield wipers
Switch on the ignition (page 42).
iTo signal minor directional changes such as
changing lanes, press combination switch only
to point of resistance and release. The corre-
sponding turn signal will flash three times.
!Do not operate the windshield wipers when
the windshield is dry. Dust that accumulates on
a windshield might scratch the glass and/or
damage the wiper blades when wiping occurs on
a dry windshield. If it is necessary to operate the
windshield wipers in dry weather conditions,
always operate the windshield wipers with wind-
shield washer fluid (
page 64).
!If anything blocks the windshield wipers
(leaves, snow, etc.), switch them off immediate-
ly.
For safety reasons, stop the vehicle in a safe
location and
remove SmartKey from starter switch
or
turn off the engine by pressing the
KEYLESS-GO* start/stop button and
open the driver’s door (with the driver’s
door open, starter switch is in
position0, same as with SmartKey
removed from starter switch)
before attempting to remove any blockage.
Remove blockage.
Turn the windshield wipers on again.
164.boo Seite 62 Freitag, 30. März 2007 12:54 12
Page 64 of 601
63 Getting started
Driving
Switching on windshield wipers
Turn the combination switch to the
desired position depending on the
intensity of the rain.
MWindshield wipers off
USlow intermittent wiping
Rain sensor operation with low
sensitivity.
VFast intermittent wiping
Rain sensor operation with high
sensitivity.
uSlow continuous wiping
tFast continuous wipingIntermittent wiping
Only switch on intermittent wiping under
wet weather conditions or in the presence
of precipitation.
When you select intermittent wiping, the
rain sensor is activated. The rain sensor
automatically sets a suitable wiping
interval depending on the wetness of the
sensor surface.
Turn the combination switch to
positionU orV.After the initial wipe, pauses between
wipes are automatically controlled by the
rain sensor.
Single wipe
Press the combination switch briefly in
direction of arrow1 to the resistance
point.
The windshield wipers wipe one time
without washer fluid.
If windshield wipers fail to function at all in the
combination switch positionU orV,
set the combination switch to the next
higher wiper speed
have the windshield wipers checked at the
nearest authorized Mercedes-Benz Light
Truck Center
!Do not leave windshield wipers on an inter-
mittent setting when the vehicle is taken to an
automatic car wash or during windshield clean-
ing. Wipers will operate in the presence of water
sprayed on the windshield, and windshield
wipers may be damaged as a result.
!If you have set intermittent wiping, dirt on
the surface of the rain sensor or optical effects
may cause the windshield wipers to wipe in an
undesired fashion. This could then damage the
windshield wiper blades or scratch the windows.
You should therefore switch off the windshield
wipers when weather conditions are dry.
iIntermittent wiping is interrupted when the
vehicle is at a standstill and a front door is
opened. This protects persons getting into or out
of the vehicle from being sprayed.
Intermittent wiping will be continued when all
doors are closed and
the automatic transmission is set to
positionD orR
or
the wiper setting is changed using the
combination switch
164.boo Seite 63 Freitag, 30. März 2007 12:54 12
Page 65 of 601
64 Getting started
Driving
Wiping with windshield washer fluid
Press the combination switch in direc-
tion of arrow1 past the resistance
point.
The windshield wipers operate with
washer fluid.
For information on cleaning the headlamps
with washer fluid, see “Headlamp cleaning
system*” (
page 208).
For information on filling up the washer
reservoir, see “Windshield/rear window
washer system and headlamp cleaning
system*” (
page 383).
Rear window wiper/washer
The combination switch is located on the
left of the steering column.
Combination switch
1Rear window wiper switch
2Wiping rear window with washer fluid
3Intermittent wiping
4Rear window wiper off
5Wiping rear window with washer fluid6Rear window wiper indicator
Switch on the ignition (page 42).
Activating intermittent wipe
Turn rear window wiper switch1 to
position3 (
page 64).
In the lower multifunction display you
will see indicator6, indicating that
the rear window wiper is activated.
iTo prevent smears on the windshield or
noisy/chattering wiper blades, wipe with
windshield washer fluid every now and then even
when it is raining.
iThe rear window wiper engages automatical-
ly when the automatic transmission is shifted to
positionR with the windshield wipers switched
on.
164.boo Seite 64 Freitag, 30. März 2007 12:54 12
Page 180 of 601
179 Controls in detail
Control system
Press buttonj ork repeatedly
until the message
Compass Setting
Zone
appears in the multifunction
display.
The selection marker is on the current
setting.
Press buttonæ orç to set the
respective compass zone.
For information on how to call up the
compass, see “Compass” (
page 344).Compass calibration
This function is not available if your vehicle
is equipped with the COMAND system and
navigation module*.
In order to calibrate the compass properly,
mind the following:
Calibrate the compass in open terrain.
Nearby buildings, bridges, power lines
and large antenna masts, for example,
could impair compass calibration.
Switch off electrical consumers (e.g.
climate control, windshield wipers, or
rear window defroster).
Close all doors and the tailgate.
Start the engine (page 56).
Press buttonæ orç to move
the selection marker to the
Vehicle
submenu.
Press buttonj ork repeatedly
until the message
Compass Calibration appears in the
multifunction display.
The selection marker is on setting
switched Off.
Press buttonæ to set the selection
marker to
Start.
The following message appears in the
multifunction display:
Compass Calibration Active
Please drive in a full circle.
iMake sure you are in area where you can
drive a full circle with your vehicle without dis-
turbing traffic in order to calibrate the compass.
164.boo Seite 179 Freitag, 30. März 2007 12:54 12
Page 209 of 601
208 Controls in detail
Good visibility
For information on windshield wipers, see
“Windshield wipers” (
page 62).
Headlamp cleaning system*
The headlamps will automatically be
cleaned with a high-pressure water jet
when you have
switched on the headlamps
and
operated the windshield wipers with
windshield washer fluid five times
When you switch off the headlamps, the
counter resets.
For information on filling up the washer
reservoir, see “Windshield/rear window
washer system and headlamp cleaning
system*” (
page 383).
Rear view mirrors
For more information on setting the rear
view mirrors, see “Mirrors” (
page 51).
Interior rear view mirror, antiglare
position
1Lever
Tilt the mirror to the antiglare position
by moving lever1 towards the wind-
shield.
The interior rear view mirror is dimmed.Auto-dimming rear view mirrors*
The reflection brightness of the exterior
rear view mirror on the driver’s side and
the interior rear view mirror will respond
automatically to glare when
the ignition is switched on
and
incoming light from headlamps falls on
the sensor in the interior rear view
mirror
The rear view mirror will not react if
the automatic transmission is set to
positionR
the interior lighting is turned on
164.boo Seite 208 Freitag, 30. März 2007 12:54 12
Page 223 of 601
222 Controls in detail
Climate control
Deactivating
Press button| (page 216) once
more.
The indicator lamp on the button goes
out. Defrosting is turned off.
The previous settings are in effect
again. The air conditioning compressor
remains switched on.Windshield fogged on the outside
Switch the windshield wipers on
(
page 63).
Press button| (page 216).
The indicator lamp on the button
comes on.
The climate control switches automatically
to the following functions:
most efficient blower speed and
heating power, depending on outside
temperature
air flows onto the windshield and the
door windows (side air vents must be
open)
the air conditioning compressor
switches on at outside temperatures
above approximately 41°F (5°C) for
air-dryingIf the automatic air distribution is switched
off:
Press air distribution button9 ora
(
page 216).
Air recirculation mode
Switch to air recirculation mode to prevent
unpleasant odors from entering the vehicle
from the outside (e.g. before driving
through a tunnel). This setting cuts off the
intake of outside air and recirculates the
air in the passenger compartment.
iTo switch off, you can also press
button´ orU (
page 216).
iKeep this setting selected only until the
windshield is clear again.
Warning!G
Fogged windows impair visibility,
endangering you and others. If the windows
begin to fog on the inside, switching off the
air recirculation mode immediately should
clear interior window fogging. If interior win-
dow fogging persists, make sure the air
conditioning (
page 216) is activated, or
press button|.
164.boo Seite 222 Freitag, 30. März 2007 12:54 12
Page 238 of 601
237 Controls in detail
3-zone automatic climate control*
Windshield fogged on the outside
Switch the windshield wipers on
(
page 63).
Press buttonU (page 230).
The indicator lamp on buttonU
goes out. Air volume and air
distribution are controlled separately
for each zone.
If the automatic air distribution and
air volume are switched off:
Press buttons8 andY
(
page 230).
Maximum cooling MAXCOOL
If the air distribution control as well as the
airflow volume control are set toU and
there is a high need for cooling, the
MAXCOOL function is activated.
“
MAXCOOL” appears in the front and rear
display.
This provides the fastest possible cooling
of the vehicle interior (when windows and
tilt/sliding sunroof* are closed).
Air recirculation mode
Switch to air recirculation mode to prevent
unpleasant odors from entering the vehicle
from the outside (e.g. before driving
through a tunnel). This setting cuts off the
intake of outside air and recirculates the
air in the passenger compartment.
iKeep this setting selected only until the
windshield is clear again.
Warning!G
Fogged windows impair visibility,
endangering you and others. If the windows
begin to fog on the inside, switching off the
air recirculation mode immediately should
clear interior window fogging. If interior win-
dow fogging persists, make sure the air
conditioning (
page 239) is activated, or
press button|.
164.boo Seite 237 Freitag, 30. März 2007 12:54 12