remote control MERCEDES-BENZ M-CLASS 2007 User Guide

308 Controls in detailUseful features
Press release button in direction of
arrow1 and take mobile phone
cradle3 out in direction of arrow2.
Installing a different mobile phone cra-
dle
Example illustration1Contact plate
2Recesses
3Mobile phone cradle
Insert mobile phone cradle3 into
recesses2 of contact plate1.

Push mobile phone cradle3 forward
until it engages.
Tele Aid*
Shortly after the completion of your
Tele Aid acquaintance call, you will receive
a user ID and password. By visiting
www.mbusa.com and selecting “Tele Aid”
(USA only), you will have access to account
information, remote door unlock and
more.The Tele Aid system
(Tele
matic A
larm I
dentification on
D
emand)
The Tele Aid system consists of three
types of response:

automatic and manual emergency


roadside assistance


information
The Tele Aid system is operational provid-
ing that the vehicle’s battery is charged,
properly connected, not damaged and cel-
lular and GPS coverage is available.
The speaker volume of a Tele Aid call can
be adjusted by using the volume control on
the COMAND system or on the multifunc-
tion steering wheel. To raise, turn the rota-
ry volume control on COMAND system
clockwise or press buttonæ on the
multifunction steering wheel. To lower,
turn the rotary volume control on
COMAND system control counterclock-
wise or press buttonç on the multi-
function steering wheel.
!
The initial activation of the Tele Aid system
may only be performed by completing the sub-
scriber agreement and placing an acquaintance
call using the ¡button. Failure to complete
either of these steps will result in a system that
is not activated.
If you have any questions regarding activation,
please call the Response Center at
1-800-756-9018 (in the USA) or
1-888-923-8367 (in Canada).

ProCarManuals.com

315 Controls in detail
Useful features
Remote door unlock
In case you have locked your vehicle unin-
tentionally (e.g. SmartKey inside vehicle),
and the reserve SmartKey is not handy:
Contact the Mercedes-Benz Response
Center at 1-800-756-9018 (in the USA)
or 1-888-923-8367 (in Canada).
You will be asked to provide your pass-
word which you provided when you
completed the subscriber agreement.

Then return to your vehicle and pull the
tailgate recessed handle for minimum
of 20 seconds until the SOS button is
flashing.
The message
Connecting call
ap-
pears in the multifunction display.As an alternative, you may unlock the vehi-
cle via Internet using the ID and password
sent to you shortly after the completion of
your acquaintance call.
The Response Center will then unlock your
vehicle with the remote door unlocking
feature.Stolen Vehicle Recovery services
In the event your vehicle was stolen:

Report the incident to the police.
The police will issue a numbered
incident report.

Pass this number on to the
Mercedes-Benz Response Center along
with your password issued to you when
you subscribed to the service.
The Response Center will then attempt
to covertly contact the vehicle’s
Tele Aid system. Once the vehicle is
located, the Response Center will
contact the local law enforcement and
you. The vehicle’s location will only be
provided to law enforcement.
!
If the indicator lamp continues to flash or
the system does not reset, contact the Response
Center at 1-800-756-9018 (in the USA) or
1-888-923-8367 (in Canada), or Mercedes-Benz
Customer Assistance at 1-800-FOR-MERCedes
(1-800-367-6372) in the USA or Customer
Service at 1-800-387-0100 in Canada.
i
The remote door unlock feature is available
if the relevant cellular phone network is avail-
able.
The SOS button will flash and the message
Connecting call
will appear in the multifunc-
tion display to indicate receipt of the door unlock
command.
Once the vehicle is unlocked, a Response Center
specialist may attempt to establish voice contact
with the vehicle occupants.
If the tailgate recessed handle was pulled for
more than 20 seconds before door unlock autho-
rization was received by the Response Center,
you must wait 15 minutes before pulling the tail-
gate recessed handle again.
ProCarManuals.com

316 Controls in detailUseful featuresGarage door opener*
The integrated remote control is capable of
operating up to three separately controlled
devices. It provides a convenient way to re-
place up to three hand-held remote con-
trols used to operate devices such as
garage door openers, gate openers, or oth-
er devices compatible with HomeLink
® or
some other systems.
Before the integrated remote control can
be used, it must be programmed to the ga-
rage door opener, gate operator or other
device you wish to operate. See the follow-
ing instructions for programming informa-
tion.
Interior rear view mirror with integrated
remote control1Indicator lamp
2 3 4Signal transmitter button
Needed for programming (not part of vehi-
cle equipment):
5Hand-held remote control of ga-
rage door opener, gate operator
or other device
6Hand-held remote control but-
ton
i
When the anti-theft alarm stays on for more
than 30 seconds, a call is initiated automatically
to the Response Center. See anti-theft alarm
system (
page 103).
Warning!
G
Before programming the integrated remote
control to a garage door opener or gate
operator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage. When programming
a garage door opener, the door moves up or
down. When programming a gate operator,
the gate opens or closes.
Do not use the integrated remote control
with any garage door opener that lacks
safety stop and reverse features as required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982).
A garage door that cannot detect an object
– signaling the door to stop and reverse –
does not meet current U.S. federal safety
standards.
ProCarManuals.com

317 Controls in detail
Useful features
Programming the integrated remote
control
Step 1:
Switch on the ignition (
page 40).Step 2:

If you have previously programmed a
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when indicator lamp1
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory.
If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and be-
gin directly with step 3.Step 3:

Hold end of the hand-held remote
control5 of the device you wish to
train approximately 2 to 5 in
(5 to 12 cm) away from the signal
transmitter button (2, 3 or4) to be
programmed, while keeping the indica-
tor lamp1 in view.
Step 4:

Using both hands, simultaneously
press hand-held remote control
button6 and the desired signal trans-
mitter button (2, 3 or4). Do not
release the buttons until step 5 is com-
pleted.
Indicator lamp1 will flash, first slowly
and then rapidly.
When programming a garage door opener,
park the vehicle outside the garage.
Do not run the engine while programming
the integrated remote control. Inhalation of
exhaust gas is hazardous to your health.
All exhaust gas contains carbon monoxide
(CO), and inhaling it can cause unconscious-
ness and possible death.
i
Indicator lamp1 flashes immediately the
first time the signal transmitter button is
programmed. If this button has already been
programmed, the indicator lamp will only start
flashing after 20 seconds.

ProCarManuals.com

318 Controls in detailUseful featuresStep 5:
After indicator lamp1 changes from a
slow to a rapidly flashing light, release
the hand-held remote control button
and the signal transmitter button.
Step 6:

Press and hold the just-trained signal
transmitter button (2, 3 or4) and
observe indicator lamp1.
If indicator lamp1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button (2, 3 or4) is pressed and re-
leased.Step 7:

To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
Rolling code programming
To train a garage door opener (or other
rolling code devices) with the rolling code
feature, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
Step 8:

Locate “training” button on the garage
door opener motor head unit.
Exact location and color of the button
may vary by garage door opener brand.
Depending on manufacturer, the
“training” button may also be referred
to as “learn” or “smart” button. If there
is difficulty locating the transmitting
button, refer to the garage door opener
Operator’s Manual.Step 9:

Press the “training” button on the ga-
rage door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the follow-
ing two steps.
Step 10:

Return to the vehicle and firmly press,
hold for 2 seconds and release the pro-
grammed signal transmitter button
(2, 3 or4).
Step 11:

Press, hold for 2 seconds and release
same signal transmitter button a sec-
ond time to complete the training pro-
cess.
i
If indicator lamp1 flashes rapidly for about
2 seconds and then turns to a constant light,
continue with programming steps 8 through 12
as your garage door opener may be equipped
with the “rolling code” feature.
i
Some garage door openers (or other rolling
code equipped devices) may require you to
press, hold for 2 seconds and release the same
signal transmitter button a third time to
complete the training process.

ProCarManuals.com

319 Controls in detail
Useful features
Step 12:
Confirm the garage door operation by
pressing the programmed signal trans-
mitter button (2, 3 or4).
Step 13:

To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the
integrated signal transmitter to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:Step 4:

Press and hold the signal transmitter
button (2, 3 or4). Do not release
this button until it has been successful-
ly trained.

While still holding down the signal
transmitter button (2, 3 or4),
“cycle” your hand-held remote control
button6 as follows: Press and hold
button6 for 2 seconds, then release
it for 2 seconds, and again press and
hold it for 2 seconds. Repeat this se-
quence on the hand-held remote con-
trol until the frequency signal has been
learned. Upon successful training,
indicator lamp1 will flash slowly and
then rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete.Reprogramming a single signal trans-
mitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:

Switch on the ignition (
page 40).

Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.

Indicator lamp1 will begin to flash af-
ter 20 seconds. Without releasing the
signal transmitter button, proceed with
programming starting with step 3.
i
Upon completion of programming the inte-
grated remote control, make sure you retain the
hand-held remote control that came with the ga-
rage door opener, gate operator or other device.
You may need it for use in other vehicles, for fu-
ture programming of an integrated remote con-
trol, or simply for continued use as a hand-held
remote control to operate the respective device
in other situations.
ProCarManuals.com

320 Controls in detailUseful featuresOperation of integrated remote control
Switch on the ignition (
page 40).

Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing the integrated remote control
memory

Switch on the ignition (
page 40).

Simultaneously press and hold outer
signal transmitter buttons2 and 4,
for approximately 20 seconds, until
indicator lamp1 flashes rapidly. Do
not hold for longer than 30 seconds.
The codes of all three channels are
erased.Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:


Check the frequency of hand-held
remote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 280-390 MHz.


Put a new battery in hand-held remote
control5. This will increase the likeli-
hood of the hand-held remote control
sending a faster and more accurate sig-
nal to the integrated remote control.


While performing step 3, hold
hand-held remote control5 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming. Attempt varying an-
gles at the distance of 2 to 5 inches
(5 to 12 cm) away or the same angle at
varying distances.


If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.


Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.
i
If you sell your vehicle, erase the codes of all
three channels.
i
Certain types of garage door openers are in-
compatible with the integrated remote control. If
you should experience further difficulties with
programming the integrated remote control,
contact an authorized Mercedes-Benz Center, or
call Mercedes-Benz Customer Assistance
Center (in the USA only) at 1-800-FOR-MER-
Cedes, or Customer Service (in Canada) at
1-800-387-0100.
ProCarManuals.com

557 Index
Cup holders 298
Cleaning 299
Front center console 299
Front center console,
Removing/Installing 299
Rear armrest 299
Curb weight 395
Current transmission program
mode (AMG vehicles only) 147
D
Date display, Setting 169, 170
Daytime running lamp mode 138
Setting 171
Deep water see Standing water
Defogging windshield 213, 227
Defrosting, Front 213, 227
Defrosting, Rear 205
Delayed shut-off
Exterior lamps 172
Interior lighting 173
Department of Transportation see DOT
Diesel engine
Preglow indicator lamp 29Difficulties
While driving 63
While starting 57
Digital clock see Clock
Digital speedometer 147, 155
Dimensions, Vehicle 541
Direction of rotation (tires) 368
Displays
Digital speedometer 147, 155
Distronic* 253
Maintenance service indicator 401
Messages in the
multifunction display 428
Multifunction display 147
Outside temperature 147, 155
Selecting 168
Symbol messages 446
Text messages 430
Vehicle status message 163, 428
Vehicle system settings,
Control system 151, 153, 164
Distance to empty (range), Trip
Computer 180Distronic* 250
Activating 256
Cleaning system sensor 408
Control system 255
Deactivating 259
Distance warning function* 179, 263
Driving hints 261
Messages in the
multifunction display 432
Sensor cover 408
Warning and indicator lamps 253
Door
Entry lamps 144
Locking, In an emergency 476
Locking/unlocking,
KEYLESS-GO* 39, 68
Locking/unlocking, SmartKey 38, 68
Messages in the
multifunction display 455
Opening from inside/outside 109,
118
Remote door unlock (Tele Aid*) 315
Unlocking, Mechanical key 475
ProCarManuals.com

559 Index
Emergency operations
Remote door unlock, Tele Aid* 315
Unlocking/opening the tailgate 476
Emergency Tensioning Device see ETD
Emergency, In case of
Battery, Jump starting 515
Engine shut-down 525
First aid kit 469
Flat tire 497
Fuses 522
Hazard warning flasher 142
Instrument cluster, Indicator
lamps 414, 415, 416, 417, 418,
419, 420, 421, 422, 423, 424
Roadside Assistance 12, 312
Towing the vehicle 518
Emission control 350
Information label 531
System warranties 10
Vacuum line routing diagram
label 531Engine
Belt layout (ML 320 CDI) 532
Belt layout (ML 350) 532
Belt layout (ML 500) 532
Belt layout (ML 63 AMG) 533
Block heater (Canada only) 400
Break-in recommendations 358
Cleaning 406
Compartment 356
Emergency engine shut-down 525
Malfunction indicator lamp 29, 449
Maximum engine speed 146, 534,
535
Messages in the
multifunction display 449
Number 531
Starting 54
Starting with KEYLESS-GO* 55
Starting with the SmartKey 55
Tachometer 29, 146
Technical data 534
Turning off with KEYLESS-GO* 67
Turning off with the SmartKey 67Engine coolant see Coolant
Engine oil 358, 546
Adding 361, 546
Additives 546
Changing 361, 546
Checking level 358
Checking level with the
control system (ML 500 only) 358
Checking with the oil dipstick
(except ML 500) 360
Consumption 358
Filler neck (ML 350, ML 320 CDI) 361
Filler neck (ML 500, ML 63 AMG) 361
Messages in display 359, 453
Messages in the
multifunction display 453
Recommended engine oils
and oil filters 546
Engine oil level 358
ESP
®
27, 98
Four wheel electronic traction system
with ESP
®
98
Messages in the
multifunction display 436, 437
Off-road-ESP®
101
Warning lamp 27, 419, 420
ProCarManuals.com

563 Index
Interior lighting 142
Delayed shut-off 173
Interior rear view mirror 49
Antiglare positions 200
Auto-dimming mirrors* 201
Interior storage spaces see
Storage compartments
Intermittent wiping
Windshield wipers 61
J
Jack 471
Lifting the vehicle 498
Jump starting 515
K
Key, Mechanical 475
Key, SmartKey 108
Batteries 111, 480
Battery check lamp 108
Checking battery condition 111
Closing the power windows
(Convenience closing feature) 239
Closing the tilt/sliding sunroof*
(Convenience closing feature) 239
Closing, Power tailgate* 123
Factory setting 109Locking/unlocking 38, 68, 108
Locking/unlocking, Global
setting 109
Loss of 111
Messages in the
multifunction display 457
Opening the power windows
(Summer opening feature) 239
Opening the tilt/sliding sunroof*
(Summer opening feature) 239
Remote control 108
Replacing batteries 480
Selective setting 110
Starter switch positions 40
Starting the engine 54
Turning off the engine 67
Unlocking and opening,
Power tailgate* 111
Key, SmartKey with KEYLESS-GO*
Batteries 116, 480
Battery check lamp 112
Checking battery condition 116
Closing the power windows
(Convenience closing feature) 239
Closing the tilt/sliding sunroof*
(Convenience closing feature) 239Closing, Power tailgate* 124
Closing/locking, Power
tailgate* 125
Factory setting 115
Important notes 113
Locking/unlocking 39, 68, 112
Locking/unlocking, Global
setting 115
Loss of 117
Messages in the
multifunction display 456, 457
Opening the power windows
(Summer opening feature) 239
Opening the tilt/sliding sunroof*
(Summer opening feature) 239
Remote control 112
Replacing batteries 480
Selective setting 115
Start/stop button 41
Starter switch positions 40, 41
Starting the engine 55
Turning off the engine 67
Unlocking and opening,
Power tailgate* 117
ProCarManuals.com