seats MERCEDES-BENZ M-CLASS 2007 Owner's Guide

286 Controls in detailLoadingReturning the rear seat backrest to
original position
1Seat backrest
2Seat cushion
Fold seat backrest1 rearward until it
engages.
The red indicator5 (
page 285)
should no longer be visible.

Fold seat cushion2 rearward until it
locks into position.

Check for secure locking by pushing
and pulling on the seat backrest.
Cargo compartment cover blind
The cargo compartment cover blind can be
installed behind the rear seats.1Handle
2Mount
Rolling out blind

Pull blind on handle1 across the car-
go compartment.

Guide blind into mounts2 and re-
lease.
Rolling up blind

Disengage blind and guide retraction
by its handle1.
Warning!
G
If a red indicator is visible with the backrest
up, then the backrest is not properly locked
into position.
Always lock backrest in its upright position
when the rear seats are occupied, or the ex-
tended cargo compartment is not in use.
Check for secure locking by pushing and
pulling on the backrest.!
With the cargo compartment cover blind in-
stalled, do not pile luggage higher than the lower
edges of the rear side windows.
ProCarManuals.com

287 Controls in detail
Loading
Removing blind
1Release button
2Blind
Roll the blind up (
page 286).

Push release button1.

Pull blind2 to the left against the
spring pressure until the spring in the
cover audibly engages.

Remove the blind.
Installing blind

Place left side of blind2 in left mount.

Position right side of blind2 over right
mount.

Press release button1 and guide
cover2 into mount.

Make sure the cargo compartment
cover blind is securely fastened.
Partition net*
i
Before removing cargo compartment cover
blind behind the rear seats, fold the left or right
rear seat forward. Afterwards, return the left or
right rear seat into its original position.
i
Before installing cargo compartment cover
blind behind the front seats, fold the rear seats
forward.
Warning!
G
Make sure the partition net is properly en-
gaged at top and bottom position and the
tightening belts are securely fastened.
Never use a damaged partition net.
To help avoid personal injury from smaller
objects being thrown around in the occu-
pant compartment during a collision or sud-
den maneuver, always use partition net
when transporting cargo.
The partition net cannot prevent the move-
ment of large, heavier objects into the pas-
senger compartment in an accident. Such
items must be properly secured using the
cargo tie-down rings (
page 283) in the
cargo compartment floor.
Passenger use of seats behind installed par-
tition net is restricted because of the foot-
well being taken up by the net.
ProCarManuals.com

288 Controls in detailLoadingUse of the partition net is a particularly im-
portant safety factor when the vehicle is
loaded higher than the top of the seat
backrests with smaller objects. For your
safety, always use the partition net when
transporting cargo.
The partition net can be installed in two
locations:
1Holder in B-pillar
2Holder in C-pillar


Without the cargo compartment ex-
panded (
page 284), use holders
above C-pillars2 and the cargo
tie-down rings in the cargo compart-
ment (
page 283).


With the cargo compartment expanded
(page 284), use holders above
B-pillars1 and the cargo tie-down
rings behind the front seats
(page 283).

Open the zipper on the partition net
package.

Roll out the partition net.

Unfold the partition net.
The partition net bars must audibly
engage.Installing the partition net
Partition net bar hung up behind the C-pillar1Holder
2Partition net bar
Hang partition net bar2 on holder1
as indicated by the arrow.

Push partition net bar2 forward into
holder1 in direction of arrow.
ProCarManuals.com

289 Controls in detail
Loading
Pulling the partition net tightBelt hook attached behind the front seats1Belt hook
2Cargo tie-down ring
3Tightening belt
Hook belt hook1 into cargo tie-down
ring2 in direction of arrow.

Pull tightening belt3 by the loose end
in direction of arrow until the partition
net is pulled tight.

After driving a short distance, make
sure the partition net is still tight and, if
necessary, pull it tight again.Loosening the partition net
Belt hook attached behind the front seats1Buckle
2Belt hook
3Cargo tie-down ring
Loosen the tightening belt by pulling
buckle1 upward in direction of arrow.

Remove belt hook2 from cargo
tie-down ring3.Removing and storing the partition net

Take partition net bar2 out of
holder1, see “Installing the partition
net” (
page 288).

Press the red button on the upper and
lower partition net bar.

Fold the partition net.

Roll up the partition net.

Close the zipper on the partition net
package.
ProCarManuals.com

292 Controls in detailLoading
Place load between the cargo net and
the side wall of the cargo compart-
ment.

Press locking button3 on belt
reel1. With the other hand, slowly
pull net over load until it is taut.
Telescoping rod
1Telescoping rod
2Mounting element

Insert one mounting element2 into
each cargo rail.

Turn mounting element2 in cargo rail
toN.

Insert telescoping rod1 into mount-
ing element2.

Turn mounting element2 in cargo rail
until it engages in the‹ position.
You should be able to feel the mounting
element engage in the cargo rail.Removing rear seat cushions
If your vehicle is equipped with the cargo
management system* you can remove the
rear seat cushions.
Removing the rear seat cushions will pro-
vide you with a larger cargo compartment.

Fold the seat cushions forward
(page 285).
1Release lever

Pull seat cushion release lever1 and
remove the seat cushion by pulling it
upward.

Remove the head restraints
(page 129).
i
The telescoping rod can be used to tighten
the load against the rear seats so as to secure it
from slipping.

ProCarManuals.com

297 Controls in detail
Useful features
3Storage compartment
4Coin holder
Opening the storage tray
Pull button1 and lift up armrest.
Opening the storage compartment

Pull button2 and lift up armrest.
The coin holders4 are located in front
of storage compartment3.Rear storage compartments
Depending on the vehicle configuration,
your vehicle may be equipped with two
storage compartments in the front of the
rear seats.

Briefly press the front of the cover.
The storage compartment opens
automatically.
Parcel nets
i
If your vehicle is equipped with a smoking
package*, the storage compartment contains an
ashtray (
page 300).
Warning!
G
Do not place objects with a combined
weight of more than 4.4 lbs (2 kg) into the
parcel net on the back of the front passen-
ger seat. Otherwise, the Occupant Classifi-
cation System OCS (
page 85) may not be
able to properly approximate the occupant
weight category.
Parcel nets are intended for storing
light-weight items only.
Heavy objects, objects with sharp edges or
fragile objects may not be transported in the
parcel nets. In an accident, during hard
braking, or sudden maneuvers, they could
be thrown around inside the vehicle and
cause injury to vehicle occupants.
Parcel nets cannot protect transported
goods in the event of an accident.
ProCarManuals.com

300 Controls in detailUseful featuresAshtrays*
Your vehicle is equipped with an ashtray
and a cigarette lighter (
page 301) locat-
ed in the front center console and an ash-
tray located in front of the rear seats
(
page 300).
Ashtray in the center console
1Ashtray insert
2Cover plateOpening the ashtray

Briefly touch cover plate2.
The ashtray opens automatically.
Removing ashtray insert

Grip the ashtray insert1 on the sides
and pull it out upwards.
Reinstalling ashtray insert

Install ashtray insert1.

Close ashtray cover plate2.Rear center console ashtray (front of
rear seats)
1Ashtray
2Ashtray cover
i
If your vehicle is not equipped with a smok-
ing package*, it has a storage compartment
(
page 296) with a power outlet (
page 302)
instead.
Warning!
G
Remove ashtray only with vehicle standing
still. Set the parking brake to secure vehicle
from movement. Set automatic transmis-
sion toP. With the automatic transmission
set toP, turn off the engine.
!
Close the ashtray when not in use and be-
fore folding the rear seats
ProCarManuals.com

302 Controls in detailUseful features
Power outletsPower outlets are located


in the front center console
(page 302)


in the rear center console (
page 303)


on the right-hand side of the cargo
compartment (
page 303)
Power outlet in front center console
1Power outlet cover

Switch on the ignition (
page 40).

Open cover plate (
page 296).

Pull out cover1 and insert electrical
plug (cigarette lighter type).
!
The lighter socket can accommodate
12V DC electrical accessories (up to a maximum
of 180 W) designed for use with the standard
“cigarette lighter” plug type. Keep in mind, how-
ever, that connecting accessories to the lighter
socket (for example extensive connecting and
disconnecting, or using plugs that do not fit prop-
erly) can damage the lighter socket. With the
socket damaged, the lighter may no longer be
able to be placed in the heating (pushed-in) posi-
tion, or the lighter may pop out too early with the
lighter not hot enough.
To help avoid damaging the cigarette lighter
socket, we recommend connecting 12V DC elec-
trical accessories designed for use with the stan-
dard “cigarette lighter” plug type to the 12V
power outlets (
page 302) in your vehicle
whenever possible.
i
If the engine is off, and the cigarette lighter
is being used extensively, the vehicle battery
may become discharged.
!
If you use all power outlets in the vehicle,
make sure that the maximum current drawn
does not exceed 55 A.
i
The power outlets can be used to
accommodate 12V DC electrical accessories
(e.g. air pump, auxiliary lamps) up to a maximum
of 240 W.
If the engine is off, the battery may become dis-
charged if used for long periods of time.
i
You can use the power outlet in the cargo
compartment or in the front of the rear seats
even if the ignition is switched off.
An emergency shut-off feature ensures that the
vehicle’s electrical voltage does not fall below a
minimum level. If the voltage drops to this mini-
mum level, the power outlets are automatically
switched off. This ensures that enough power re-
mains to start the engine.
ProCarManuals.com

394 OperationTires and wheels
Tire ply material
1Plies in sidewall
2Plies under tread
This marking tells you about the type of
cord and number of plies in the sidewall
and under the tread.
Tire and loading terminology
Accessory weight
The combined weight (in excess of those
standard items which may be replaced) of
automatic transmission, power steering,
power brakes, power windows, power
seats, radio, and heater, to the extent that
these items are available as
factory-installed equipment (whether
installed or not).
Air pressure
The amount of air inside the tire pressing
outward on each square inch of the tire.
Air pressure is expressed in pounds per
square inch (psi), or kilopascal (kPa) or
bars.
Aspect ratio
Dimensional relationship between tire
section height and section width
expressed in percentage.
Warning!
G
The temperature grade for this tire is estab-
lished for a tire that is properly inflated and
not overloaded. Excessive speed, underin-
flation, or excessive loading, either sepa-
rately or in combination, can cause
excessive heat build-up and possible tire
failure.
i
For illustration purposes only. Actual data
on tires are specific to each vehicle and may vary
from data shown in above illustration.
ProCarManuals.com

412 OperationVehicle careSeat belts
Only use clear, lukewarm water and
soap.
Upholstery
Using aftermarket seat covers or wearing
clothing that have the tendency to give off
coloring (e.g. when wet, etc.) may cause
the upholstery to become permanently dis-
colored. By lining the seats with a proper
intermediate cover, contact-discoloration
will be prevented.Leather upholstery*
Please not that leather upholstery is a
natural product and is therefore subject to
a natural aging process. Leather uphol-
stery may also react to certain ambient
influences such as high humidity or high
temperature by showing wrinkles for
example.

Wipe leather upholstery with a damp
cloth and dry thoroughly or clean with
Mercedes-Benz approved Leather
Care.
Exercise particular care when cleaning
perforated leather as its underside should
not become wet.
MB Tex upholstery

Use Mercedes-Benz approved Interior
Care onto a soft, lint-free cloth and
apply with light pressure for cleaning
the upholstery.
Wood trims

Dampen cloth using water and use
damp cloth to clean wood trims in your
vehicle.
!
The seat belts must not be treated with
chemical cleaning agents. Do not dry the seat
belts at temperatures above 176°F (80°C) or in
direct sunlight.
Warning!
G
Do not bleach or dye seat belts as this may
severely weaken them. In a crash they may
not be able to provide adequate protection.
Warning!
G
Only use seat or head restraint covers which
have been tested and approved by
Mercedes-Benz for your vehicle model.
Using other seat or head restraint covers
may interfere with or prevent the activation
of the active head restraints. Contact an
authorized Mercedes-Benz Light Truck
Center for availability.
!
Wipe with light pressure to avoid damage to
the upholstery.
!
Do not use solvents like tar remover or
wheel cleaner nor polishes or waxes as these
may be abrasive.
ProCarManuals.com