warning lights MERCEDES-BENZ ML320 1997 Complete User Guide

253 Practical hints
What to do if …
Problem
Possible cause
Suggested solution
:
The yellow warning lamp flashes
after starting the engine or while
driving.
The engine oil level has sunk to the minimum
level. If the engine oil level continues to sink,
the warning lamp will light up.

Add approved oil at the next gas
station (
page 302).

If oil loss is visible on the engine, have
the malfunction corrected as soon as
possible at a Mercedes-Benz Light
Truck Center.
_
The red indicator lamp does not
go out after starting the engine.
The adjustable telescoping steering column
is not properly locked.

Lock the adjustable steering column
(page 39).
‡
The green front fog lamp indica-
tor lamp lights up when ignition
is turned on.
The front fog lamps are switched on.

Fog lamps (
page 111).
<
The red seat belt warning lamp
illuminates for a brief period
after starting the engine.
The warning lamp reminds you to fasten seat
belts.

Fasten your seat belt (
page 64).
W
The yellow low washer system
fluid level lamp comes on after
starting the engine or while driv-
ing.
There is approximately 1.3 US qt. (1.25 l) of
washer fluid remaining in the reservoir.

Add washer fluid (
page 224).
The washer fluid may have frozen.

Move the vehicle to a warmer environ-
ment so that the washer fluid will
thaw.

Correct the concentration level after
the washer fluid in the reservoir
thaws.

255 Practical hints
What to do if …
Problem
Possible cause
Suggested solution
1
The red SRS indicator lamp lights
up while driving.
There is a malfunction in the restraint sys-
tems. The airbags or emergency tensioning
device (ETDs) could deploy unexpectedly or
fail to activate in an accident.

Drive with added caution to the near-
est authorized Mercedes-Benz Light
Truck Center.
Warning!
G
In the event a malfunction of the SRS is indi-
cated as outlined above, the SRS may not be
operational. For your safety, we strongly
recommend that you visit an authorized
Mercedes-Benz Light Truck Center immedi-
ately to have the system checked, otherwise
the SRS may not be activated when needed
in an accident, which could result in serious
or fatal injury, or it might deploy unexpect-
edly and unnecessarily which could result in
an accident / or injury to you or to others.

267 Practical hints
Replacing bulbs
Rear lamps Notes on bulb replacement


Use only 12-volt bulbs of the same type
and with the specified watt rating.


Switch lights off before changing a bulb
to prevent short circuits.


Always use a clean lint-free cloth when
handling bulbs.


Your hands should be dry and free of oil
and grease.


If the newly installed bulb does not light
up, visit an authorized Mercedes-Benz
Light Truck Center.


Have the LEDs and bulbs for the follow-
ing lamps replaced by an authorized
Mercedes-Benz Light Truck Center:

Additional turn signals in the exteri-
or rear view mirrors


Bi-Xenon lamps*


Front fog lamps (vehicles with sport
package)*
Lamp
Type
6
Brake lamp
1073
(32 cp bulb)
7
Backup lamp
1073
(32 cp bulb)
8
Turn signal lamp
PY 21 W
9
Tail, parking and
standing lamp
Rear fog lamp, driv-
er’s side
P 21 / 4 W
a
Side marker lamp
W5W
b
High mounted brake
lamp
1073
(32 cp bulb)
c
License plate lamps
C 5 W
Warning!
G
Keep bulbs out of reach of children.
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Halogen lamps contain pressurized gas. A
bulb can explode if you:

touch or move it when hot


drop the bulb


scratch the bulb
Wear eye and hand protection.
Because of high voltage in xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.

268 Practical hintsReplacing bulbsReplacing bulbs for front lamps
Replacing low beam bulbs
1Low beam halogen or Bi-Xenon* head-
lamp cover with locking tab2Electrical connector
Bi-Xenon* headlampHalogen headlamp

Switch off the lights.

Open the hood (
page 217).

Push down tab at top end of cover1
and remove.

Pull electrical connector2 off.

Unclip the retainer springs and take out
the bulb.

Insert the new bulb so that the base lo-
cates in the recess on the holder.

Clip the retainer springs.

Plug the connector2 onto the bulb.

Align headlamp cover and click into
place.
Warning!
G
Do not remove the cover
1
for the
Bi-Xenon headlamp. Because of high voltage
in xenon lamps, it is dangerous to replace
the bulb or repair the lamp and its compo-
nents. We recommend that you have such
work done by a qualified technician.

282 Practical hintsJump startingThe battery is located on the right side of
the engine compartment.
Make sure the two vehicles do not
touch.

Turn off all electrical consumers.

Apply parking brake.

Shift gear selector lever to positionP.

Open the hood.

Connect positive terminals1 and4
of the batteries with the jumper cable.
Clamp cable to positive terminal4 of
charged battery first.1Positive terminal of discharged battery
2Negative terminal of discharged
battery
3Negative terminal of charged battery
4Positive terminal of charged battery

Start engine of the vehicle with the
charged battery and run at idle speed.

Connect negative terminals2 and3
of the batteries with the jumper cable.
Clamp cable to negative terminal3 of
charged battery first.

Start the engine of the disabled vehi-
cle.
Now you can turn on the electrical
consumers. Do not turn on the lights under
any circumstances.

Remove the jumper cables first from
the negative terminals2 and3 and
then from positive terminals1
and4.
You can now turn on the lights.

Have the battery checked at the
nearest authorized Mercedes-Benz
Light Truck Center.
Warning!
G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(page 223).
!Never invert the terminal connections.
!Do not tow-start the vehicle.

311 Technical terms
ABS
(A
ntilock B
rake S
ystem)
Prevents the wheels from locking up
during braking so that the vehicle can
continue to be steered.
BabySmart
TM airbag deactivation
system
This system detects if a special system
compatible child restraint seat is in-
stalled on the front passenger seat. The
system will automatically deactivate
the passenger front airbag when such a
seat is properly installed (indicator
lamp7 in the instrument cluster
lights up). See your authorized
Mercedes-Benz Light Truck Center for
availability.
BabySmartTM compatible child seats
Special restraint system for children.
The sensor system for the passenger
seat prevents deployment of the pas-
senger front airbag if a BabySmart
TM
compatible child seat is installed.BAS
(B
rake A
ssist S
ystem)
System for potentially reducing braking
distances in emergency braking situa-
tions. The system is activated when it
senses an emergency based on how
fast the brake is applied.
Bi-Xenon headlamps*
Headlamps which use an electric arc as
the light source and produce a more in-
tense light than filament headlamps.
Bi-Xenon headlamps produce low
beam and high beam.
CAC
(C
ustomer A
ssistance C
enter)
Mercedes-Benz customer service cen-
ter, which can help you with any ques-
tions about your vehicle and provide
assistance in the event of a break-
down.CAN system
(C
ontroller A
rea N
etwork)
Data bus network serving to control ve-
hicle functions such as door locking or
windshield wiping.
Cockpit
All instruments, switches, buttons and
indicator / warning lamps in the pas-
senger compartment needed for vehi-
cle operation and monitoring.
Cruise control
Driving convenience system for auto-
matically maintaining the vehicle speed
set by the driver.
Engine number
The number set by the manufacturer
and placed on the cylinder block to
uniquely identify each engine pro-
duced.

GF54.30-P-3010A
Function of acoustic warnings
24.10.96

MODEL
129, 140 as of 1.6.96,

163, 168, 170,

202 as of 1.8.96,

208 up to 31.7.99,

210 as of 1.6.96 up to 30.6.99

Display
Function

Turn signal indicator

ticking
Switching on the turn signal indicator is

indicated acoustically by the turn signal

indicator ticking. The driver's attention is

brought to a defect in the turn signal system

by the turn signal indicator ticking at a higher

frequency.

Turn signal indicator ticking is generated

electromagnetically. The frequency

corresponds to that of the turn signal indicator

lamp.

The signal comes from the combination relay

(turn signal indicator with trailer coupling, rear

window defroster), wiper motor, ATA (N10/2),

on model 210 from the multi-function control
module (N10-1) or from the driver-side signal-

acquisition and actuation module (SAM)

(N10/1), on model 163 from the All-Activity

Module (AAM, N10), on model 168 it is

generated by the integrated turn signal

indicator control in the instrument cluster (A1).

Parking brake reminderThe parking brake warning sounds when

terminal 15g is ON from a speed of approx. 5

km/h.
Piezoelectric loudspeaker (quartz), function

GF54.30-P-3017A

Gear warning, model 168

only with automatic

transmission or automatic

clutch
The acoustic gear warning is active, when

D
a gear is engaged
and

D
the brake is
not
depressed
and

D
the accelerator pedal is
not

pressed
and


D
the driver's door is opened.

These conditions are processed in the gear

recognition module (A61) or in the automatic

clutch control module (N15/4). The

information on the status of the driver's door

is available as a CAN message. It is

transmitted by the instrument cluster (A1).

Piezoelectric loudspeaker (quartz), function

GF54.30-P-3017A

Speed warning
The speed warning sounds when terminal

15g is ON from a speed of approx. 120 km/h.

(on national variants only)

Piezoelectric loudspeaker (quartz), function

GF54.30-P-3017A

Speed limit warning
The warning sounds if the set maximum

speed is exceeded by at least 6 km/h.
(on vehicles with variable cruise control only)

Piezoelectric loudspeaker (quartz), function

GF54.30-P-3017A

Seat belt reminder
On national variants only
Piezoelectric loudspeaker (quartz), function

GF54.30-P-3017A

Switched-on lights

reminder
The switched-on lights reminder sounds when

terminal 15g is OFF, terminal 58k is ON,

when the starter key is removed and the

driver's door is opened.
Piezoelectric loudspeaker (quartz), function

GF54.30-P-3017A

Key reminder
The key reminder when terminal 15g is OFF

and the driver's door is open when the starter

key is inserted
Piezoelectric loudspeaker (quartz), function

GF54.30-P-3017A

Soft top reminder, model

170 only
The soft top reminder sounds when terminal

15 is ON and soft top reminder input is on low

level.
Piezoelectric loudspeaker (quartz), function

GF54.30-P-3017A

Copyright DaimlerChrysler AG 05.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1

GF54.30-P-2001A
Indicator / warning displays, function
24.10.96

MODEL
129, 140 as of 1.6.96,

163, 168, 170,

202 as of 1.8.96,

208 up to 31.7.99,

210 as of 1.6.96 up to 30.6.99

The table below lists the various warning alarms and indications

according to type (visual/acoustic) and their actuation (direct/CAN).

Visual warning and indicator signals actuated over direct lines:
D
Left turn signal indicator lamp (A1e1)

D
Right turn signal indicator lamp (A1e2)

D
High beam indicator lamp (A1e3)

D
Fuel reserve warning lamp (A1e4)

D
Brake fluid / parking brake warning lamp (A1e7) (except model

163)

D
Low windshield washer fluid level warning lamp (A1e13) (as of

01.09.01 also valid for model 163)

D
Low engine coolant level warning lamp (A1e11) (except model

168, model 163 as of 3.99)

D
Coolant level and temperature warning lamp (A1e11) (only model

168 as of 9.99 and only coolant level function)

D
Generator charge indicator/warning lamp (A1e5)

D
Seat belt warning lamp (A1e9)

D
Seatbelt/backrest lock warning lamp (A1e9)

D
Exterior lamp failure indicator lamp (A1e14)

-----------------------------------------------------------------------------------------
D

Hydraulic fluid level warning lamp (A1e37)

D
ADS warning lamp, suspension (A1e27)

D
Steering lock warning lamp (A1e40) (only

I
)

D
SRS airbag malfunction indicator lamp (A1e15)

D
AIRBAG OFF indicator lamp (A1e56), only model 163 except

I

Also refer to document: Indicator and warning signals triggered

over CAN data lines
Acoustic warning and indicator signals actuated over direct

lines:
D
Turn signal ticker

D
Seat belt reminder

D
Switched-on lights reminder

D
Key warning

D
Soft top warning, only model 170


Also refer to document: Acoustic warnings, function

Acoustic warning and indicator signals actuated over CAN data

lines:
D
Parking brake warning

D
Vehicle speed warning

D
Vehicle speed limit warning

D
Gear warning, only model 168


Also refer to document: Acoustic warnings, function

Indicator and warning signals triggered over

direct lines

GF54.30-P-3002A

Indicator and warning signals triggered over

CAN data lines

GF54.30-P-3003A
Acoustic warnings, function
GF54.30-P-3010A

Copyright DaimlerChrysler AG 04.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1

GF54.30-P-2001A
Indicator / warning displays, function
24.10.96

MODEL
129, 140 as of 1.6.96,

163, 168, 170,

202 as of 1.8.96,

208 up to 31.7.99,

210 as of 1.6.96 up to 30.6.99

The table below lists the various warning alarms and indications

according to type (visual/acoustic) and their actuation (direct/CAN).

Visual warning and indicator signals actuated over direct lines:
D
Left turn signal indicator lamp (A1e1)

D
Right turn signal indicator lamp (A1e2)

D
High beam indicator lamp (A1e3)

D
Fuel reserve warning lamp (A1e4)

D
Brake fluid / parking brake warning lamp (A1e7) (except model

163)

D
Low windshield washer fluid level warning lamp (A1e13) (as of

01.09.01 also valid for model 163)

D
Low engine coolant level warning lamp (A1e11) (except model

168, model 163 as of 3.99)

D
Coolant level and temperature warning lamp (A1e11) (only model

168 as of 9.99 and only coolant level function)

D
Generator charge indicator/warning lamp (A1e5)

D
Seat belt warning lamp (A1e9)

D
Seatbelt/backrest lock warning lamp (A1e9)

D
Exterior lamp failure indicator lamp (A1e14)

-----------------------------------------------------------------------------------------
D

Hydraulic fluid level warning lamp (A1e37)

D
ADS warning lamp, suspension (A1e27)

D
Steering lock warning lamp (A1e40) (only

I
)

D
SRS airbag malfunction indicator lamp (A1e15)

D
AIRBAG OFF indicator lamp (A1e56), only model 163 except

I

Also refer to document: Indicator and warning signals triggered

over CAN data lines
Acoustic warning and indicator signals actuated over direct

lines:
D
Turn signal ticker

D
Seat belt reminder

D
Switched-on lights reminder

D
Key warning

D
Soft top warning, only model 170


Also refer to document: Acoustic warnings, function

Acoustic warning and indicator signals actuated over CAN data

lines:
D
Parking brake warning

D
Vehicle speed warning

D
Vehicle speed limit warning

D
Gear warning, only model 168


Also refer to document: Acoustic warnings, function

Indicator and warning signals triggered over

direct lines

GF54.30-P-3002A

Indicator and warning signals triggered over

CAN data lines

GF54.30-P-3003A
Acoustic warnings, function
GF54.30-P-3010A

Copyright DaimlerChrysler AG 05.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1

GF54.30-P-3002A
Indicator and warning signals triggered over direct lines, function
24.10.96

MODEL
129, 140 as of 1.6.96,

163, 168, 170,

202 as of 1.8.96,

208 up to 31.7.99,

210 as of 1.6.96 up to 30.6.99

Indicator and warning signals

Indicator lamps for left turn signal (A1e1) and right turn signal

(A1e2)
The signal in models 129, 140, 170, 202 comes from the

combination relay (turn signals with trailer coupling, rear

window defroster, wiper motor, anti-theft alarm system)

(N10/2), and in model 210 from the multifunction control

module (N10-1) or the driver's side signal acquisition and

actuation module (SAM) (N10/1).

In model 168 the entire turn signal control is located in the

instrument cluster (A1).

Brake fluid / parking brake warning lamp (A1e7)

The signal for the brake fluid comes direct from the brake fluid level switch (S11) (except model 163).

(The signal for the parking brake comes over CAN.)

Low windshield washer fluid level warning lamp (A1e13) except

models 163 and 168
See

document: Coolant/washer fluid level voltage coding, task /

function

-----------------------------------------------------------------------------------------
Low windshield washer fluid level warning lamp (A1e13) as of

01.09.01 for model 163
See document: Displaying washer fluid level, function

Low engine coolant level warning lamp (A1e11) except models

163 and 168
See

document: Coolant/washer fluid level voltage coding, task /

function

Low engine coolant level warning lamp (A1e11) model 163 as of

3.99
See

document: Displaying coolant level, function

Coolant level and temperature warning lamp (A1e11) model 168

as of 9.99
See

document: Displaying coolant level, function

Fuel reserve warning lamp (A1e4)
When the reserve fuel level is reached, this lamp lights up and

goes out again only after refueling is detected. If the vehicle is

refueled with the ignition ON, refueling is detected only if at

least 7 liters of fuel are added.

-----------------------------------------------------------------------------------------

AIRBAG OFF indicator lamp (A1e56), only model 163 except

I

The signal comes from the emergency tensioning retractor

(ETR) control module with airbag (AB, N2/2)

Generator charge indicator/warning lamp (A1e5)

See document: Terminal 61 and terminal 61e, charge indicator

lamp, exterior lamp failure, function

Seatbelt/backrest lock warning lamp (A1e9)

The seat belt warning lamp is only used in a few national

versions, and is actuated direct by a seat belt buckle switch
(normally closed contact). After engine start, the lamp flashes

for a short time (approx. 6 seconds).

In model 129 if this lamp fails to go out after flashing briefly, but

continues to shine constantly, then the seat backrest is not

locked.
Exterior lamp failure indicator lamp (A1e14)

The signal comes from the lamp failure monitor

See document: Terminal 61 and terminal 61e, charge indicator

lamp, exterior lamp failure, function
Hydraulic fluid level warning lamp (A1e37)
The signal comes direct from the ADS level control oil level

switch (S44).

ADS warning lamp, suspension (A1e27) The signal comes from the ADS control module, suspension
(N51).

SRS airbag malfunction indicator lamp (A1e15)
The signal comes from the emergency tensioning retractor

(ETR) control module with airbag (AB, N2/2)

Voltage coding of coolant / windshield washer

fluid level, function
Except models 163 and 168

GF54.30-P-3006A

Displaying coolant level, function
Model 163 as of 3.99

GF54.30-P-3028GH

Model 168 as of 9.99

GF54.30-P-3028GC

Terminal 61 and terminal 61e, charge

indicator lamp, exterior lamp failure, function

GF54.30-P-3007A

Copyright DaimlerChrysler AG 04.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1