key MERCEDES-BENZ ML320 1997 Complete Repair Manual

11
Switching from Hands Free to Handset Operation
If you are using the phone in Hands Free operation and wish to switch to Handset operation:
Switching from Handset to Hands Free Operation
With the phone in the cradle, close the flip to switch the call from Handset to Hands Free mode.
Muting and Unmuting a Hands Free Call
To Mute

Press the mute key on the radio keypad.
To Unmute

Depress the mute key on the radio keypad.
Muting and Unmuting a Handset Call
To Mute

Press
MUTE

(+
).
This mutes the call so the other party cannot hear you speaking.
To Unmute

Press
UNMUTE

(+
).
Step

11 1 1

Open the flip on your phone.
22 2 2

Remove the phone and cradle from the holder.
33 3 3

Begin speaking.

S-B-82.70/179A February 20022 TDMA PROGRAMMING
1. Obtain the following information from the cellular carrier before beginning the programming sequence:
• Cellular telephone number: __ __ __ - __ __ __ - __ __ __ __
• Carrier system I.D.: __ __ __ __ __ (I.D. number will be 1 to 5 digits)
2. Obtain the telephone security code from the customer. In a new telephone, it is set to 000000.
• Telephone security code: __ __ __ __ __ __ (Default is all zeros)
3. Program as follows:
StepToPress (Input)Phone Displays
1Enter Programming
ModePress: #, Carrier System I.D., #, *,
“SEND”Enter Security Code
_ _ _ _ _ _
2 Enter Security CodePress: 0, 0, 0, 0, 0, 0 and select
“OK” (This is the factory default
code)ESN (Hex)
3 Enter Phone NumberScroll down to MIN: --- --- --- ----
and insert the ten digit MIN
through the keypad and select
“OK” (MIN is the customer’s
cellular number)IMSI
4Finalizing
ProgrammingSelect “DONE” (The handset
display will turn off temporarily)Main Menu
Note: The telephone will display “Try Again” if an entry error is made. Press “CLR” to erase the
message/incorrect digits or press and hold “CLR” to clear all digits and then enter the correct number
and press “SEND.”
4. The telephone will power off after the “NAM Program Begins” message displays. W hen the telephone is
powered up again, it will search for the network and be ready for use.

S-B-82.70/179A
February 20023 CDMA PROGRAMMING
1. Obtain the following information from the cellular carrier before beginning the programming sequence:
• Cellular telephone number: __ __ __ - __ __ __ - __ __ __ __
• Carrier analog system I.D.: __ __ __ __ __ (I.D. number will be 1 to 5 digits)
• Carrier digital system I.D.: __ __ __ __ __ (I.D. number will be 1 to 5 digits)
Note: Generally, the analog and digital system I.D. numbers will be the same. Questions regarding
system I.D. numbers should be addressed with the cellular carrier.
2. Program as follows:
StepToPress (Input)Telephone Displays
1Enter
Programming
ModePress: 7, 4, 6, 6, 3, #, MENU,
MENUNam 1
Nam 2
2
Selecting NAM Choose “SELECT” for NAM 1 MIN: 0000000000
3Enter Phone
NumberInsert the ten digit MIN
through the keypad and select
“OK” (This is the customer’s
cellular number)IMSI
4Enter AMPS
System I.D.Scroll down to AMPS Sys ID,
insert the number and select
“OK” (AMPS data is provided
by the carrier)CDMA Sys ID:
5Enter CDMA
System I.D.Insert the CDMA Sys ID and
select “OK” (CDMA data is
provided by the carrier)MIN:
6Finalizing
ProgrammingSelect “DONE” and then press
the “END” keyMain Menu
Note: The telephone will display “Try Again” if an entry error is made. Press “CLR” to erase the
message/incorrect digits or press and hold “CLR” to clear all digits and then enter the correct number
and press “STO.”
3. After the “Entry Done” message appears, the telephone will display “Searching” as it attempts to contact
a network. W hen the “Searching” message disappears, the telephone is ready for use.
4. To program a second number, follow step 1 in the table below and steps 2-6 in the above table.
StepToPress (Input)Phone Displays
1Enter NAM2
Programming
Mode7, 4, 6, 6, 3, #, 2, FCN, FCN Enter MIN
Note: Be sure to obtain the system I.D. for each before beginning the programming sequence if the
second through fourth numbers are with different cellular carriers.
Note: The CDMA telephone has a two telephone number maximum. Refer to the operation guide for
instructions on how to switch between the various telephone numbers.

AD54.30-P-3000-02A
Warning buzzer function check IC

Warning buzzer
D
Light reminder and parking brake reminder

D
Key reminder

I
D
Seat belt reminder

for approx. 6 s

I
,
M
,
H
and Korea

for approx. 12 s

G

The warning tone is interrupted as soon as the seat belt buckle is

inserted.

D
Warning tone for a shortage of oil

D
Vehicle speed warning

G
> 120 km/h, v-limit warning (cruise

control)

D
In addition the symbol for vehicle speed warning appears in the
instrument cluster with multi-function display.
D

On model 163 a warning tone sounds for approx. 5 seconds if the

CAN signal is unusable.

D
Model 168 with automatic clutch system features an audible gear

warning.

It sounds if a gear is engaged at the same time as the driver's

door is opened. Brake and accelerator pedal must not be

operated.

Copyright DaimlerChrysler AG 05.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1

AR82.30-P-6100GHRemoving and installing wiper arm
7.3.97

MODEL
163.113 /128 /136 /154 /157 /172 /174 /175

P82.30-0386-11

1
Protective cap

2
Nut


Remove/install

Danger!

Injury hazard
by trapping or crushing, in

extreme cases with loss of limbs when

reaching into windshield wiper mechanism
Always remove ignition key when working on

windshield wiper mechanism.

AS82.30-Z-0001-01A

1
Ensure that wiper motor is in park position

2
Open protective cap (1)

3
Unscrew nut (2)


*BA82.30-P-1002-01C

4
Take off wiper arm


Hold wiper arm on mounting section to

avoid hitting against windshield.

5
Install in the reverse order


Windshield wipers

Number

Designation
Model

Series 163

BA82.30-P-1002-01C
Nut for wiper arm on windshield
Nm
18

Copyright DaimlerChrysler AG 09.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1

AR82.30-P-6400GH
Remove/install wiper system
3.3.97

MODEL
163.113 /128 /136 /154 /157 /172 /174 /175

P82.30-0393-06

1
Nuts

2
Wiper system

3
Connector

M6/1
Wiper motor


Remove/install

Danger!

Injury hazard
by trapping or crushing, in

extreme cases with loss of limbs when

reaching into windshield wiper mechanism
Always remove ignition key when working on

windshield wiper mechanism.

AS82.30-Z-0001-01A

1
Ensure that wiper motor is in park position

2
Remove cover on air intake

AR83.25-P-1405GH

3
Unscrew nuts (1) on wiper arm

4
Lift wiper system (2)

5
Disconnect connector (3) from the wiper

motor (M6/1)

6
Remove wiper system (2)

7
Install in the reverse order

Copyright DaimlerChrysler AG 09.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1