engine coolant MERCEDES-BENZ ML350 2008 W164 Owner's Guide
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2008, Model line: ML350, Model: MERCEDES-BENZ ML350 2008 W164Pages: 561
Page 525 of 561
524 Technical data
Fuels, coolants, lubricants
ModelCapacityFuels, coolants, lubricants etc.
Fuel tankAll models25.1 US gal (95.0 l)Gasoline engine:
Premium unleaded gasoline
Minimum Posted Octane 91
(Avg. of 96 RON/86 MON)
Diesel engine:
ULTRA-LOW SULFUR HIGHWAY DIESEL FUEL
(15 ppm SULFUR MAXIMUM)
including a reserve ofAll except
ML 63 AMGapprox. 3.5 US gal (13.0 l)
including a reserve ofML 63 AMGapprox. 4.0 US gal (15.0 l)
Air conditioning systemAll modelsR-134a refrigerant and special PAG lubricant
oil (never R-12)
Windshield washer system and
headlamp cleaning system*All models8.1 US qt (7.7 l)MB Windshield Washer Concentrate1
1Use MB Windshield Washer Concentrate “MB SummerFit” and water for temperatures above freezing or MB Windshield Washer Concentrate “MB SummerFit” and
commercially available premixed windshield washer solvent/antifreeze for temperatures below freezing point. Follow suggested mixing ratios (page 530).
Page 526 of 561
525 Technical data
Fuels, coolants, lubricants
Engine oils
Engine oils are specifically tested for their
suitability in our engines and durability for
our service intervals. Therefore, only use
approved engine oils and oil filters
required for vehicles with Maintenance
System. For a listing of approved engine
oils and oil filters, refer to the Factory
Approved Service Products pamphlet
(USA only), or contact an authorized
Mercedes-Benz Light Truck Center.Engine oil additives
Air conditioning refrigerant
R-134a (HFC) refrigerant and special PAG
lubricating oil are used in the air condition-
ing system.
Brake fluid
Only brake fluid approved by
Mercedes-Benz is recommended. Any
authorized Mercedes-Benz Light Truck
Center will provide you with additional
information.
!Using engine oils and oil filters of
specification other than those expressly
required for the Maintenance System, or chang-
ing of oil and oil filter at change intervals longer
than those called for by the Maintenance System
will result in engine or emission control system
damage not covered by the Mercedes-Benz
Limited Warranty.
Please follow Maintenance System recommen-
dations for scheduled oil changes. Failure to do
so will result in engine or emission control
system damage not covered by the
Mercedes-Benz Limited Warranty.
!Do not blend oil additives with engine oil.
They may damage the engine.
Damage or malfunctions resulting from blending
oil additives are not covered by the
Mercedes-Benz Limited Warranty.
!Never use R-12 (CFC) or mineral-based
lubricating oil. Otherwise damage to the system
will occur.
Warning!G
During vehicle operation, the boiling point of
the brake fluid is continuously reduced
through the absorption of moisture from the
atmosphere. Under extremely strenuous
operating conditions, this moisture content
can lead to the formation of bubbles in the
system, thus reducing the system’s
efficiency.
Therefore, the brake fluid must be replaced
regularly. Refer to your vehicle’s
Maintenance Booklet for replacement inter-
val.
Page 527 of 561
526 Technical data
Fuels, coolants, lubricants
Premium unleaded gasoline
(gasoline engine)
Fuel requirements
Gasoline engine
Only use premium unleaded fuel:
The octane number (posted at the
pump) must be 91 min. It is an average
of both the Research Octane Number
(RON) and the Motor Octane Number
(MON): (RON+MON) /2. This is also
known as the ANTI-KNOCK INDEX.
Unleaded gasoline containing oxygenates
such as ethanol, IPA, IBA and TBA can be
used provided the ratio of any one of these
oxygenates to gasoline does not
exceed 10%; MTBE must not exceed 15%.
The ratio of methanol to gasoline must not
exceed 3% plus additional cosolvents.
Using mixtures of ethanol and methanol is
not allowed. Gasohol, which contains
10% ethanol and 90% unleaded gasoline,
can be used.
Warning!G
Gasoline is highly flammable and poisonous.
It burns violently and can cause serious
personal injury.
Never allow sparks, flame or smoking mate-
rials near gasoline!
Turn off the engine before refueling.
Whenever you are around gasoline, avoid in-
haling fumes and skin or clothing contact,
extinguish all smoking materials.
Direct skin contact with fuels and the inha-
lation of fuel vapors are damaging to your
health.
!To maintain the engine’s durability and per-
formance, premium unleaded gasoline must be
used. If premium unleaded gasoline is not avail-
able and low octane fuel is used, follow these
precautions:
Have the fuel tank only partially filled with
unleaded regular gasoline and fill up with
premium unleaded gasoline as soon as
possible.
Avoid full throttle driving and abrupt acceler-
ation.
Do not exceed an engine speed of 3000 rpm
if the vehicle is loaded with a light load such
as two persons and no luggage.
Do not exceed 2/3 of maximum accelerator
pedal position if the vehicle is fully loaded or
operating in mountainous terrain.
Page 528 of 561
527 Technical data
Fuels, coolants, lubricants
These blends must also meet all other fuel
requirements, such as resistance to spark
knock, boiling range, vapor pressure, etc.
Diesel engine
Only use commercially available vehicular
ULTRA-LOW SULFUR HIGHWAY DIESEL
FUEL (15 ppm SULFUR MAXIMUM).
To prevent malfunctions, diesel fuel with
improved cold flow characteristics is of-
fered in the winter months. Check with
your fuel retailer.Gasoline additives (gasoline engine)
A major concern among engine
manufacturers is carbon build-up caused
by gasoline. Mercedes-Benz recommends
only the use of quality gasoline containing
additives that prevent the build-up of
carbon deposits.
After an extended period of using fuels
without such additives carbon deposits
can build up, especially on the intake
valves and in the combustion area, leading
to engine performance problems such as:
Warm-up hesitation
Unstable idle
Knocking/pinging
Misfire
Power lossIn areas where carbon deposits may be
encountered due to lack of availability of
gasolines which contain these additives,
Mercedes-Benz recommends the use of
additives approved by us for use on
Mercedes-Benz vehicles. Refer to the
Factory Approved Service Products
pamphlet (USA only) or contact an
authorized Mercedes-Benz Light Truck
Center for a listing of approved product(s).
Follow directions on product label.
Do not blend other fuel additives with fuel.
This only results in unnecessary costs and
may be harmful to the engine operation.
!Do not fill the tank with gasoline. Do not
blend diesel fuel with gasoline or kerosine. The
fuel system and engine will otherwise be
damaged, which is not covered by the
Mercedes-Benz Limited Warranty.
!Damage or malfunction resulting from poor
fuel quality or from blending additional fuel
additives other than those tested and approved
by us for use on Mercedes-Benz vehicles are not
covered by the Mercedes-Benz Limited
Warranty.
Page 529 of 561
528 Technical data
Fuels, coolants, lubricants
Coolants
The engine coolant is a mixture of water
and anticorrosion/antifreeze, which
provides:
Corrosion protection
Freeze protection
Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory
with a coolant providing freeze protection
to approximately -35°F (-37°C) and corro-
sion protection.If the antifreeze mixture is effective to
-35°F (-37°C), the boiling point of the cool-
ant in the pressurized cooling system is
reached at approximately 266°F (130°C).
The coolant solution must be used year
round to provide the necessary corrosion
protection and increase boil-over protec-
tion. Refer to Maintenance Booklet for
replacement interval.
Coolant system design and coolant used
determine the replacement interval. The
replacement interval published in the
Maintenance booklet is only applicable if
MB 325.0 Anticorrosion/Antifreeze solu-
tion or other Mercedes-Benz approved
products of equal specification are used to
renew the coolant concentration or bring it
back up to the proper level.
For information on other Mercedes-Benz
approved products of equal specification,
refer to the Factory Approved Service
Products pamphlet (USA only) or contact
an authorized Mercedes-Benz Light Truck
Center.To provide important corrosion protection,
the solution must be at least 50% anticor-
rosion/antifreeze (equivalent to freeze
protection to approximately -35°F
[-37°C]). If you use a solution that is more
than 55% anticorrosion/antifreeze (freeze
protection to approximately -49°F
[-45°C]), the engine temperature will
increase due to the lower heat transfer
capability of the solution. Therefore, do not
use more than this amount of anticorro-
sion/antifreeze.
If the coolant level is low, water and
MB 325.0 Anticorrosion/Antifreeze
should be used to bring it up to the proper
level (have cooling system checked for
signs of leakage). Please make sure the
mixture is in accordance with label instruc-
tions.
The water in the cooling system must meet
minimum requirements, which are usually
satisfied by normal drinking water. If you
are not sure about the water quality, con-
sult an authorized Mercedes-Benz Light
Truck Center.
!Add premixed coolant solution only. Adding
water and MB 325.0 Anticorrosion/Antifreeze
separately from each other, could cause engine
damage not covered by the
Mercedes-Benz Limited Warranty.
Page 530 of 561
529 Technical data
Fuels, coolants, lubricants
Anticorrosion/antifreeze
Your vehicle contains a number of
aluminum parts. The use of aluminum
components in motor vehicle engines
necessitates that anticorrosion/antifreeze
coolant used in such engines be
specifically formulated to protect the aluminum parts. Failure to use such
anticorrosion/antifreeze coolant will result
in a significantly shortened service life.
Therefore, the following product is strongly
recommended for use in your vehicle:
MB 325.0 Anticorrosion/Antifreeze agent.Before the start of the winter season (or
once a year in hot southern regions), you
should have the anticorrosion/antifreeze
concentration checked. The coolant is also
regularly checked each time you bring your
vehicle to an authorized Mercedes-Benz
Light Truck Center for service.
Anticorrosion/antifreeze quantity
Approximate freeze protection
Model-35°F (-37°C)-49°F (-45°C)
ML 320 CDI
ML 3505.0 US qt (4.75 l)5.5 US qt (5.2 l)
ML 5501
1Data preliminary.
5.6 US qt (5.25 l)6.1 US qt (5.8 l)
ML 63 AMG6.1 US qt (5.8 l)6.8 US qt (6.4 l)
Page 531 of 561
530 Technical data
Fuels, coolants, lubricants
Windshield washer system and
headlamp cleaning system*
Both the windshield washer system and
headlamp cleaning system* are supplied
from the windshield washer reservoir.
The windshield washer reservoir has a ca-
pacity of approximately 8.1 US qt (7.7 l).
Refill the reservoir with MB Windshield
Washer Concentrate and water (or con-
centrate and commercially available
premixed windshield washer sol-
vent/antifreeze, depending on ambient
temperatures).Windshield and headlamp washer fluid
mixing ration
For temperatures above freezing point, use
MB Windshield Washer Concentrate
“MB SummerFit” and water:
1 part “MB SummerFit” to 100 parts
water
(1.34 fl oz [40 ml] “MB SummerFit” to
1gal [4.0l] water)
For temperatures below freezing point, use
MB Windshield Washer Concentrate
“MB SummerFit ” and commercially avail-
able premixed windshield washer
solvent/antifreeze:
1 part “MB SummerFit” to 100 parts
solvent
(1.34 fl oz [40 ml] “MB SummerFit” to
1 gal [4.0 l] solvent)Warning!G
Washer solvent/antifreeze is highly flamma-
ble. Do not spill washer solvent/antifreeze
on hot engine parts, because it may ignite
and burn. You could be seriously burned.
Page 535 of 561
534 Index
Climate control 204
Air conditioning, Cooling 214, 215
Air distribution, Front 209
Air distribution, Rear 217
Air recirculation mode 212
Air vents, Front 210
Air volume 210
Control panel*, Rear 216
Control panel, Front 206
Deactivating system 208
Defogging 212
Defrosting 210
Rear window defroster 203
Residual engine heat (REST) 215
Clock 27, 169
Cloth upholstery,
Cleaning and care of 397
Cockpit 24
Cockpit Management and Data System
see COMAND system
Cold tire inflation pressure 380
Collapsible tire 518
Collapsible tire (ML 63 AMG only) 453
Collapsible wheel chock 452COMAND system see separate operating
instructions
Combination switch 59, 60, 62, 139
Compass 307
Adjustment 173
Calibration 174
Calling up the compass 307
Control and operation of radio
transmitters 334
Control system 147
Multifunction display 147
Multifunction steering wheel 148
Resetting to factory default 164
Control system menus 147
AIRMATIC*/Compass 162
AMG menu 156
AUDIO 160
NAV* 161
Settings 163
Standard display 154
TEL* 180
Trip computer 178
Vehicle configuration 177
Vehicle status message memory 162Control system submenus 151, 153, 166
Comfort* 176
Instrument cluster 167, 168
Lighting 170
Time/Date 169
Vehicle 173
Coolant 345, 528
Anticorrosion/antifreeze
mixing ratio and quantity 529
Capacities 522
Checking coolant level 339, 345
Messages in the multifunction
display 431, 433
Temperature 336
Temperature display 154
Corner-illuminating front fog lamps* 140
Messages in the multifunction
display 439
Replacing bulbs 469
Crossing obstacles 325
Cruise control 244
Activating 246
Messages in the multifunction
display 416
Page 538 of 561
537 Index
Engine
Belt layout (ML 320 CDI) 512
Belt layout (ML 350, ML 550) 512
Belt layout (ML 63 AMG) 512
Block heater (Canada only) 385
Break-in recommendations 343
Cleaning 391
Compartment 341
Emergency engine shut-down 506
Malfunction indicator lamp 29
Maximum engine speed 146, 513,
514
Number 511
Starting 54
Starting with KEYLESS-GO* 55
Starting with the SmartKey 55
Tachometer 29, 146
Technical data 513
Turning off with KEYLESS-GO* 67
Turning off with the SmartKey 67Engine coolant see Coolant
Engine oil 343, 525
Adding 344, 525
Additives 525
Changing 344, 525
Checking level 343
Checking with the oil dipstick 343
Consumption 343
Filler neck (ML 350, ML 320 CDI) 344
Filler neck (ML 550, ML 63 AMG) 344
Recommended engine oils and oil
filters 525
ESP
®27, 100
Four wheel electronic traction system
with ESP
®100
Messages in the multifunction
display 418, 419
Off-road-ESP
®103
Warning lamp 27, 405
ETD 87, 410
Safety guidelines 76
Expanding cargo compartment 269Exterior rear view mirrors 49, 199
Folding 201
Power folding* 200
Synchronizing 200
F
Fastening the seat belts 51
Filler neck, Engine oil
(ML 350, ML 320 CDI) 344
Filler neck, Engine oil
(ML 550, ML 63 AMG) 344
First aid kit 448
Flat tire 478
Collapsible tire
(ML 63 AMG only) 453, 518
Lifting the vehicle 479
Lowering the vehicle 487
Minispare wheel
(except ML 63 AMG) 452
Mounting the spare wheel 479
Preparing the vehicle 479
Spare wheel 518
Floormats 289
Page 539 of 561
538 Index
Fluids
Automatic transmission fluid 345
Brake fluid 340, 523, 525
Capacities 522
Engine coolant 340, 345, 528
Engine oil 343, 525
Power steering fluid 523
Windshield washer and headlamp
cleaning system* 340, 524, 530
Fog lamps 138, 139
Corner-illuminating front fog
lamps* 140
Messages in the multifunction
display 439
Rear fog lamp 139
Replacing bulbs 469
4-ETS 104
Off-road - 4-ETS 105
Front air bags 77
Front defroster 210, 225
Front lamps see HeadlampsFront passenger front air bag 72, 77
Messages in the multifunction
display 421, 422, 423, 424
Front passenger front air bag off indicator
lamp 31, 83
Front seat head restraints see
Head restraints
Front towing eye 501
Fuel 338
Additives 527
Capacities, Fuel tank 524
Consumption statistics 179
Diesel fuel 524
Filling the tank 337
Fuel filler flap and cap 337, 457
Fuel gauge 29
Fuel tank reserve warning lamp 29,
410
Premium unleaded gasoline 338,
526
Requirements, Octane rating 526Fuel cap
Messages in the multifunction
display 435
Fuel consumption statistics
Since last reset 179
Since start 179
Fuel filler flap 337
Locking/unlocking 337
Opening 337
Opening in an emergency 457
Fuel tank
Capacity 524
Filler flap 337
Fuel, Premium unleaded gasoline 524
Fuels, coolants, lubricants etc. 522
Fuses 504
Fuse box in cargo compartment 505
Fuse box in engine compartment 505
Fuse box in passenger
compartment 506
Fuse chart 448
Replacing 504