air filter MERCEDES-BENZ ML430 1997 Complete Manual Online

Fig. 38: Identifying Heater Box Function - Operating Condition No Heating
Operating condition: No heating Function
In the "no heating" operating status, the fresh air (A) is drawn in by the blower (5) into the heater housing and
routed through the dust filter (3).
The fresh air (B), which is cleaned by the dust filter (3), is subsequently routed around the heat exchanger (1).
This air conduction is controlled via the setting of the blending air flaps (6).
The cleaned fresh air (B) is routed directly into the passenger compartment via the air outlets (E, F, M and S).
The recirculated air flap (4) is closed.
Operating condition: No "recirculated air" heating

2001 Mercedes-Benz ML320
1998-2005 HVAC Climate Control - 163 Chassis
me
Saturday, October 02, 2010 3:23:15 PMPage 48 © 2006 Mitchell Repair Information Company, LLC.

Fig. 39: Identifying Heater Box Function - Operating Condition No Recirculated Air Heating
Operating condition: No "recirculating air" heating Function
In the no "recirculated air" heating mode the blower (5) draws the recirculated air (A) from the passenger
compartment over the opened recirculated air flaps (4) into the heater housing and routs it through the dust
cleaner (3). The recirculated air (B), which is cleaned by the dust filter (3), is subsequently routed around the
heat exchanger (1). This air conduction is controlled via the setting of the blending air flaps (6).
The cleaned recirculated air (B) is routed directly into the passenger compartment via the air outlets (E, F, M
and S).
The supply of fresh air is cut off by the recirculated air flap (4).
HEATER HOUSING TASK - GF83.20-P-2103-03GC
The heater housing serves to house the following components
Air ducting flaps
Dust filter
Blower
Series resistor group
Heating system heat exchanger
PTC heater booster (in model 168 with engines OM 668.940/941 as of 01.03.01)
Fresh air/recirculated air flap actuator (with model 168 as of 01.03.01)

2001 Mercedes-Benz ML320
1998-2005 HVAC Climate Control - 163 Chassis
me
Saturday, October 02, 2010 3:23:15 PMPage 49 © 2006 Mitchell Repair Information Company, LLC.

Operating condition: Air ducting in heating mode
Fig. 60: Identifying Evaporator Housing Function
- Operating Condition Air Ducting In Heating Mode
Operating condition: HEATING Function
In the heating operating status, the fresh air (A) is drawn in by the blower (5) into the evaporator housing and
routed through the dust filter (3). The air purified by the dust filter (3) is then routed through the evaporator (2)
and dried there. The fresh air (B), which has been dried, cooled and cleaned, is subsequently routed through the
heat exchanger (1). This air conduction is controlled via the setting of the blending air flaps (6).
The fresh air (B), which has been dried, cooled and cleaned, is heated up again in the heat exchanger (1). The
warm air (C) is conducted via the air outlets (E, F, M and S) into the vehicle interior. The recirculated air flap
(4) is closed.
Operating condition: Air ducting in cooling mode

2001 Mercedes-Benz ML320
1998-2005 HVAC Climate Control - 163 Chassis
me
Saturday, October 02, 2010 3:23:15 PMPage 69 © 2006 Mitchell Repair Information Company, LLC.

Fig. 61: Identifying Evaporator Housing Function - Operating Condition Air Ducting In Cooling Mode)
Operating condition: cooling Function
In the cooling operating status, the fresh air (A) is drawn in by the blower (5) into the evaporator housing and
routed through the dust filter (3). The air purified by the dust filter (3) is then routed through the evaporator (2)
and dried there. The fresh air (B), which has been dried, cooled and cleaned, is subsequently routed around the
heat exchanger (1). This air conduction is controlled via the setting of the blending air flaps (6).
The dried, cooled and cleaned air (B) is routed directly into the passenger compartment via the air outlets (E, F,
M and S). The recirculated air flap (4) is closed.
Operating condition: Blend air ducting (warm/cold) closed-loop operation

2001 Mercedes-Benz ML320
1998-2005 HVAC Climate Control - 163 Chassis
me
Saturday, October 02, 2010 3:23:15 PMPage 70 © 2006 Mitchell Repair Information Company, LLC.

Fig. 62: Identifying Evaporator Housing Function - Operating Condition Blend Air Ducting
(Warm/Cold) Closed-Loop Operation
Operating condition: Blend air (warm/cold) Function
In the blend air operating status, the fresh air (A) is drawn in by the blower (5) into the evaporator housing and
routed through the dust filter (3). The air purified by the dust filter (3) is then routed through the evaporator (2)
and dried there. Some of the dried, cold and cleaned air (B) is routed through the heat exchanger (1) and some is
routed around the heat exchanger (1). This air conduction is controlled via the central setting of the blending air
flaps (6).
The air (B), which has been dried, cooled and cleaned by the heat exchanger (1) is heated up again. After
passing through the blending air flaps (6) this heated air (C) is mixed up to form blend air (D) with the dried,
cooled and cleaned air, which was routed around the heat exchanger (1). This blend air (D) is then routed via
the air outlets (E, F, M and S) into the passenger compartment. The recirculated air flap (4) is closed.
Operating condition: Air ducting "recirculation air" in cooling mode

2001 Mercedes-Benz ML320
1998-2005 HVAC Climate Control - 163 Chassis
me
Saturday, October 02, 2010 3:23:15 PMPage 71 © 2006 Mitchell Repair Information Company, LLC.

Fig. 63: Identifying Evaporator Housing Function - Operating Condition Air Ducting Recirculation Air
In Cooling Mode)
Operating condition: Cooling down "recirculation air" Function
In the cooling mode with recirculating air the blower (5) draws the recirculated air (A) from the passenger
compartment over the opened recirculated air flaps (4) into the evaporator housing and routes it through the dust
cleaner (3). The air purified by the dust filter (3) is then routed through the evaporator (2) and dried there. The
fresh air (B), which has been dried, cooled and cleaned, is subsequently routed around the heat exchanger (1).
This air conduction is controlled via the setting of the blending air flap (6).
The dried, cooled and cleaned air (B) is routed directly into the passenger compartment via the air outlets (E, F,
M and S). The supply of fresh air is cut off by the recirculated air flap (4).
EVAPORATOR HOUSING, TASK - GF83.30-P-2104-04GH
The evaporator housing houses the following components:
Air ducting flaps
Dust filter
Blower
Series resistor group
Evaporator
Heating system heat exchanger
Expansion valve

2001 Mercedes-Benz ML320
1998-2005 HVAC Climate Control - 163 Chassis
me
Saturday, October 02, 2010 3:23:15 PMPage 72 © 2006 Mitchell Repair Information Company, LLC.

The liquefied refrigerant is routed under pressure into the fluid reservoir and flows through a stainless steel
meshing to the filter block. The pores in the filter block are matched precisely to the refrigerant's molecular size.
Thus the refrigerant can flow through the filter block.
All other matter, primarily water, is held back by this molecular filter and deposited. The cleaned refrigerant
flows over a rising pipe to the expansion valve.
Whenever the system is opened, the fluid reservoir should be replaced because of the water which has
collected there in the meantime.
ALL-ACTIVITY MODULE, LOCATION - GF83.30-P-2108-02GH
The all-activity module (AAM) (N10) is located in the left-hand side of the engine compartment. It is plugged
on from below to the fuse and relay module (F1).
Fig. 67: Identifying All
-Activity Module And Relay Module
FRESH AIR/RECIRCULATED AIR FLAP ACTUATOR, LOCATION/TASK/FUNCTION - GF83.30-P-2116GC
MODELS 163 up to 31.8.01, 168 up to 28.2.01 with CODE (580) Air conditioning or Tempmatic for USA
MODEL 163 as of 1.9.01 with code (580a) Automatic air conditioning
Shown on model 163 as of 1.09.01

2001 Mercedes-Benz ML320
1998-2005 HVAC Climate Control - 163 Chassis
me
Saturday, October 02, 2010 3:23:15 PMPage 76 © 2006 Mitchell Repair Information Company, LLC.

AIR CONDITIONING FLUID RESERVOIR, LOCATION/TASK/FUNCTION - GF83.30-P-2120GC
MODELS 163 up to 31.8.01
168 up to with code (580) Air conditioning or Tempmatic for USA
OVERVIEW OF AIR CONDITIONING (TAC) SYSTEM COMPONENTS, LOCATION/PURPOSE/DESIGN/FUNCTION -
GF83.30-P-9999GI
MODEL 163 up to 31.8.01 with CODE (580a) Automatic air conditioning
Evaporator housing, task 04GH
Evaporator housing,
function GF83.30-P-2104-
02GH
At maximum heating mode in vehicles with engine
612.963 onlyGF83.30-P-2104-
02GK
Fluid reservoir (TAC),
locationModel 168GF83.30-P-2106-
01GC
Model 163GF83.30-P-2106-
01GH
Fluid reservoir (TAC),
task
Filtering chemical and mechanical impurities out
of the refrigerant
Volume accumulator for refrigerant
Draining of refrigerant

Fluid reservoir (TAC),
function GF83.30-P-2106-
02GC
Air inlet, location/function GF83.10-P-
2138GC
Air ducts, location/purpose/design GF83.10-P-
2139GH
Blower, location/purpose/design/function GF83.10-P-
2102GC
Series resistor group, location/purpose/function GF83.10-P-
2161GC
Dust filter, location/purpose/function GF83.10-P-
2142GH
Rear vent, location/purpose/function GF83.10-P-
2143GC
Defroster vent, location/purpose/function GF83.10-P-
2144GC
Center nozzle, location/purpose/function GF83.10-P-
2149GC

2001 Mercedes-Benz ML320
1998-2005 HVAC Climate Control - 163 Chassis
me
Saturday, October 02, 2010 3:23:15 PMPage 78 © 2006 Mitchell Repair Information Company, LLC.

Fig. 73: Identifying Automatic Air Conditioning Box Function - Operating Condition Air Ducting Under
Heater Operation
Operating condition: HEATING Function
When in heating mode, the blower motor (5) draws in fresh air (A) to the automatic air conditioning box and
routes it through the multipurpose filter (3). The air cleaned by the multipurpose filter (3) is then routed to the
evaporator core (2) and dried there. The dried, cooled and filtered air (B) is then routed on through the heat
exchanger (1). This air conduction is controlled via the setting of the blending air flaps (6).
The dried, cooled and filtered air (B) is then heated up again in the hot heat exchanger (1). The warm air (C) is
routed via the air outlets (E, F, FR, M and S) into the vehicle interior.
The fresh air/recirculated air flap (4) is closed.
Operating condition: Air ducting in cooling mode

2001 Mercedes-Benz ML320
1998-2005 HVAC Climate Control - 163 Chassis
me
Saturday, October 02, 2010 3:23:16 PMPage 91 © 2006 Mitchell Repair Information Company, LLC.

Fig. 74: Identifying Automatic Air Conditioning Box Function - Operating Condition Air Ducting In
Cooling Mode
Operating condition: cooling. Function
When in cooling mode, the blower motor (5) draws in fresh air (A) to the automatic air conditioning box and
routes it through the multipurpose filter (3). The air cleaned by the multipurpose filter (3) is then routed to the
evaporator core (2) and dried there. The dried, cooled and filtered air (B) is then routed around the heat
exchanger (1). This air conduction is controlled via the setting of the blending air flaps (6).
The dried, cooled and filtered air (B) is routed directly into the passenger compartment via the air outlets (E, F,
FR, M and S). The fresh air/recirculated air flap (4) is closed.
Operating condition: Air ducting in blending mode (hot/cold) closed-loop operation

2001 Mercedes-Benz ML320
1998-2005 HVAC Climate Control - 163 Chassis
me
Saturday, October 02, 2010 3:23:16 PMPage 92 © 2006 Mitchell Repair Information Company, LLC.