lights MERCEDES-BENZ ML500 1997 Complete Owner's Guide

255 Practical hints
What to do if …
Problem
Possible cause
Suggested solution
1
The red SRS indicator lamp lights
up while driving.
There is a malfunction in the restraint sys-
tems. The airbags or emergency tensioning
device (ETDs) could deploy unexpectedly or
fail to activate in an accident.

Drive with added caution to the near-
est authorized Mercedes-Benz Light
Truck Center.
Warning!
G
In the event a malfunction of the SRS is indi-
cated as outlined above, the SRS may not be
operational. For your safety, we strongly
recommend that you visit an authorized
Mercedes-Benz Light Truck Center immedi-
ately to have the system checked, otherwise
the SRS may not be activated when needed
in an accident, which could result in serious
or fatal injury, or it might deploy unexpect-
edly and unnecessarily which could result in
an accident / or injury to you or to others.

267 Practical hints
Replacing bulbs
Rear lamps Notes on bulb replacement


Use only 12-volt bulbs of the same type
and with the specified watt rating.


Switch lights off before changing a bulb
to prevent short circuits.


Always use a clean lint-free cloth when
handling bulbs.


Your hands should be dry and free of oil
and grease.


If the newly installed bulb does not light
up, visit an authorized Mercedes-Benz
Light Truck Center.


Have the LEDs and bulbs for the follow-
ing lamps replaced by an authorized
Mercedes-Benz Light Truck Center:

Additional turn signals in the exteri-
or rear view mirrors


Bi-Xenon lamps*


Front fog lamps (vehicles with sport
package)*
Lamp
Type
6
Brake lamp
1073
(32 cp bulb)
7
Backup lamp
1073
(32 cp bulb)
8
Turn signal lamp
PY 21 W
9
Tail, parking and
standing lamp
Rear fog lamp, driv-
er’s side
P 21 / 4 W
a
Side marker lamp
W5W
b
High mounted brake
lamp
1073
(32 cp bulb)
c
License plate lamps
C 5 W
Warning!
G
Keep bulbs out of reach of children.
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Halogen lamps contain pressurized gas. A
bulb can explode if you:

touch or move it when hot


drop the bulb


scratch the bulb
Wear eye and hand protection.
Because of high voltage in xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.

268 Practical hintsReplacing bulbsReplacing bulbs for front lamps
Replacing low beam bulbs
1Low beam halogen or Bi-Xenon* head-
lamp cover with locking tab2Electrical connector
Bi-Xenon* headlampHalogen headlamp

Switch off the lights.

Open the hood (
page 217).

Push down tab at top end of cover1
and remove.

Pull electrical connector2 off.

Unclip the retainer springs and take out
the bulb.

Insert the new bulb so that the base lo-
cates in the recess on the holder.

Clip the retainer springs.

Plug the connector2 onto the bulb.

Align headlamp cover and click into
place.
Warning!
G
Do not remove the cover
1
for the
Bi-Xenon headlamp. Because of high voltage
in xenon lamps, it is dangerous to replace
the bulb or repair the lamp and its compo-
nents. We recommend that you have such
work done by a qualified technician.

269 Practical hints
Replacing bulbs
High beam bulbs
1High beam headlamp cover with lock-
ing tab
Switch off the lights.

Open the hood (
page 217).

Twist cover1 counterclockwise and
remove.2Electrical connector

Pull electrical connector2 off.

Unclip the retainer springs and take out
the bulb.

Insert the new bulb so that the base lo-
cates in the recess on the holder.

Clip the retainer springs.

Plug the connector2 onto the bulb.

Align headlamp cover and click into
place.Turn signal, parking, standing and side
marker lamp bulbs
1Bulb socket

Switch off the lights.

Open the hood (
page 217).

Twist bulb socket1 counterclockwise
and pull out.

Push bulb into socket, turn counter-
clockwise and remove.

Insert new bulb in socket, push in and
twist clockwise.

Reinstall the bulb socket.


270 Practical hintsReplacing bulbs
Align headlamp cover and click into
place.
Fog lamp bulbs
1Fog lamp

Switch off the lights.

Use a suitable object (e.g. screwdriver)
to press on the release lever behind the
front panel.
Front fog lamp1 releases.

Remove fog lamp out of bumper.2Bulb socket
3Tabs

Twist bulb socket2 counterclockwise
to its end stop and pull out.

Pull bulb out of the bulb socket.

Insert new bulb in socket.

Reinstall bulb socket2.

Twist bulb socket2 clockwise to its
end stop.

Reinstall fog lamp into the bumper.
Make sure tabs3 firmly seat into the
slots of holder.
Replacing bulbs for rear lamps
Tail lamp assemblies
Switch off the lights.

Open liftgate.
1Screws
2Tail, parking and standing lamp
Fog lamp, driver’s side
3Side marker lamp
4Turn signal lamp
5Backup lamp
6Brake lamp

Remove screws1.

Remove tail lamp.


271 Practical hints
Replacing bulbs
7Tabs
Squeeze tabs7 together and remove
bulb holder.

Gently push bulb into socket, turn
counterclockwise and remove.

Insert new bulb in socket, push in and
turn clockwise.

Reinstall bulb holder. You should hear
it engage.

Insert the tail lamp in the body, lower
edge first. Make sure it engages.

Retighten screws with washers on
them.License plate lamp
1License plate lamp
2Screws

Switch off the lights.

Loosen both screws2 and remove
lamp.

Replace the tubular lamp and reinstall
lamp.

Retighten the screws.High mounted brake lamp
1Cover
2Tab

Switch off the lights.

Squeeze both sides of cover1, fold it
forward and remove.

Press tab2 on reflector and remove
reflector.

Gently push bulb into socket, turn
counterclockwise and remove.

Insert new bulb in socket, push in and
turn clockwise.


282 Practical hintsJump startingThe battery is located on the right side of
the engine compartment.
Make sure the two vehicles do not
touch.

Turn off all electrical consumers.

Apply parking brake.

Shift gear selector lever to positionP.

Open the hood.

Connect positive terminals1 and4
of the batteries with the jumper cable.
Clamp cable to positive terminal4 of
charged battery first.1Positive terminal of discharged battery
2Negative terminal of discharged
battery
3Negative terminal of charged battery
4Positive terminal of charged battery

Start engine of the vehicle with the
charged battery and run at idle speed.

Connect negative terminals2 and3
of the batteries with the jumper cable.
Clamp cable to negative terminal3 of
charged battery first.

Start the engine of the disabled vehi-
cle.
Now you can turn on the electrical
consumers. Do not turn on the lights under
any circumstances.

Remove the jumper cables first from
the negative terminals2 and3 and
then from positive terminals1
and4.
You can now turn on the lights.

Have the battery checked at the
nearest authorized Mercedes-Benz
Light Truck Center.
Warning!
G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(page 223).
!Never invert the terminal connections.
!Do not tow-start the vehicle.

311 Technical terms
ABS
(A
ntilock B
rake S
ystem)
Prevents the wheels from locking up
during braking so that the vehicle can
continue to be steered.
BabySmart
TM airbag deactivation
system
This system detects if a special system
compatible child restraint seat is in-
stalled on the front passenger seat. The
system will automatically deactivate
the passenger front airbag when such a
seat is properly installed (indicator
lamp7 in the instrument cluster
lights up). See your authorized
Mercedes-Benz Light Truck Center for
availability.
BabySmartTM compatible child seats
Special restraint system for children.
The sensor system for the passenger
seat prevents deployment of the pas-
senger front airbag if a BabySmart
TM
compatible child seat is installed.BAS
(B
rake A
ssist S
ystem)
System for potentially reducing braking
distances in emergency braking situa-
tions. The system is activated when it
senses an emergency based on how
fast the brake is applied.
Bi-Xenon headlamps*
Headlamps which use an electric arc as
the light source and produce a more in-
tense light than filament headlamps.
Bi-Xenon headlamps produce low
beam and high beam.
CAC
(C
ustomer A
ssistance C
enter)
Mercedes-Benz customer service cen-
ter, which can help you with any ques-
tions about your vehicle and provide
assistance in the event of a break-
down.CAN system
(C
ontroller A
rea N
etwork)
Data bus network serving to control ve-
hicle functions such as door locking or
windshield wiping.
Cockpit
All instruments, switches, buttons and
indicator / warning lamps in the pas-
senger compartment needed for vehi-
cle operation and monitoring.
Cruise control
Driving convenience system for auto-
matically maintaining the vehicle speed
set by the driver.
Engine number
The number set by the manufacturer
and placed on the cylinder block to
uniquely identify each engine pro-
duced.

GF54.30-P-3010A
Function of acoustic warnings
24.10.96

MODEL
129, 140 as of 1.6.96,

163, 168, 170,

202 as of 1.8.96,

208 up to 31.7.99,

210 as of 1.6.96 up to 30.6.99

Display
Function

Turn signal indicator

ticking
Switching on the turn signal indicator is

indicated acoustically by the turn signal

indicator ticking. The driver's attention is

brought to a defect in the turn signal system

by the turn signal indicator ticking at a higher

frequency.

Turn signal indicator ticking is generated

electromagnetically. The frequency

corresponds to that of the turn signal indicator

lamp.

The signal comes from the combination relay

(turn signal indicator with trailer coupling, rear

window defroster), wiper motor, ATA (N10/2),

on model 210 from the multi-function control
module (N10-1) or from the driver-side signal-

acquisition and actuation module (SAM)

(N10/1), on model 163 from the All-Activity

Module (AAM, N10), on model 168 it is

generated by the integrated turn signal

indicator control in the instrument cluster (A1).

Parking brake reminderThe parking brake warning sounds when

terminal 15g is ON from a speed of approx. 5

km/h.
Piezoelectric loudspeaker (quartz), function

GF54.30-P-3017A

Gear warning, model 168

only with automatic

transmission or automatic

clutch
The acoustic gear warning is active, when

D
a gear is engaged
and

D
the brake is
not
depressed
and

D
the accelerator pedal is
not

pressed
and


D
the driver's door is opened.

These conditions are processed in the gear

recognition module (A61) or in the automatic

clutch control module (N15/4). The

information on the status of the driver's door

is available as a CAN message. It is

transmitted by the instrument cluster (A1).

Piezoelectric loudspeaker (quartz), function

GF54.30-P-3017A

Speed warning
The speed warning sounds when terminal

15g is ON from a speed of approx. 120 km/h.

(on national variants only)

Piezoelectric loudspeaker (quartz), function

GF54.30-P-3017A

Speed limit warning
The warning sounds if the set maximum

speed is exceeded by at least 6 km/h.
(on vehicles with variable cruise control only)

Piezoelectric loudspeaker (quartz), function

GF54.30-P-3017A

Seat belt reminder
On national variants only
Piezoelectric loudspeaker (quartz), function

GF54.30-P-3017A

Switched-on lights

reminder
The switched-on lights reminder sounds when

terminal 15g is OFF, terminal 58k is ON,

when the starter key is removed and the

driver's door is opened.
Piezoelectric loudspeaker (quartz), function

GF54.30-P-3017A

Key reminder
The key reminder when terminal 15g is OFF

and the driver's door is open when the starter

key is inserted
Piezoelectric loudspeaker (quartz), function

GF54.30-P-3017A

Soft top reminder, model

170 only
The soft top reminder sounds when terminal

15 is ON and soft top reminder input is on low

level.
Piezoelectric loudspeaker (quartz), function

GF54.30-P-3017A

Copyright DaimlerChrysler AG 05.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1

CONTENTS - FUNCTION DESCRIPTION OF EXTERIOR LIGHTING - GF82.10-P-0999A
MODELS 129, 140, 163 up to 31.08.01, 202, 208, 210 with CODE (612b) xenon headlamp unit
MODEL 163 as of 1.9.01 with CODE (614) Bi-xenon headlamp unit
MODEL 202 with CODE (236a) Special light circuit for daytime running lamps
Headlamp range control
(HRC), location of
components GF82.10-P-0001-
01GHA
Exterior lights, functionModels 129, 140,
202, 208, 210, with
Code 612b lamp unit
for Xenon headlampGF82.10-P-0003A
Electrical headlamp range adjustment
(HRA), location of componentsMODEL 208 with
code 612b xenon
headlamp unitGF82.10-P-0001-
01A
Model 210 with code
612b xenon
headlamp lamp unitGF82.10-P-0001-
01B
Model 129 with code
612b xenon
headlamp lamp unitGF82.10-P-0001-
01C
Model 140 with code
612b xenon
headlamp lamp unitGF82.10-P-0001-
01D
Model 202 with code
612b xenon
headlamp unitGF82.10-P-0001-
01E
Model 163, up to
31.08.01GF82.10-P-0001-
01GH
Model 163 as of
1.09.01GF82.10-P-0001-
01GHA
Xenon headlamp (XENON), location of
componentsModels 129, 140,
208, 210 with code
612b xenon
headlamp lamp unitGF82.10-P-0002-
01A
Model 202 with code
612b xenon
headlamp unitGF82.10-P-0002-
01B
Headlamp range adjustment, functionModels 129, 140,
202, 208, 210 with
code 612b xenon
headlamp unitGF82.10-P-0001A

2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Electrical System - Body - 163 Chassis
me
Saturday, October 02, 2010 3:30:04 PMPage 19 © 2006 Mitchell Repair Information Company, LLC.