sensor MERCEDES-BENZ ML500 2003 W163 User Guide

126 Controls in detailAutomatic climate controlThe automatic climate control is operation-
al whenever the engine is running. You can
operate the climate control system in ei-
ther the automatic or manual mode. The
system cools or heats the interior depend-
ing on the selected interior temperature
and the current outside temperature.
Nearly all dust particles, pollutants and
odors are filtered out before outside air en-
ters the passenger compartment through
the air distribution system.
Automatic mode
Switching on
Briefly press button
U

(
page 125).
The indicator lamp lights up. The tem-
perature, air volume and distribution
are controlled automatically.

Adjust the temperature with the tem-
perature control4 (
page 125).
Temperature control is switched off in
the extreme position (blue or red dot).
Warning!
G
Follow the recommended settings for heat-
ing and cooling given on the following pag-
es. Otherwise the windows could fog up,
impairing visibility and endangering you and
others.
iSevere conditions (e.g. strong air pollu-
tion) may require replacement of the fil-
ter before its scheduled interval. A
clogged filter will reduce the air volume
to the interior.
If the vehicle interior is hot, ventilate
the interior before driving off.
Keep the air intake grille in front of the
windshield free of snow and debris.
Do not touch the interior temperature
sensor to maintain a precise tempera-
ture.
The set value is indicated by a lighted
segment on the control wheels.

135 Controls in detail
Power windows
Opening the windows
Press switch
k
to resistance point.
The window will move downwards until
you release the switch.
Closing the windows

Press switch
j
to resistance point.
The window will move upwards until
you release the switch.
Fully opening the windows

Press switch
k
past the point of re-
sistance and release.Fully closing the windows

Press switch
j
past the point of re-
sistance and release.
Stopping the windows

Briefly press switch
k
or
j
.
!If the side window is blocked in the up-
per area, the closing process is inter-
rupted and the window reopens
slightly.
Remove the obstruction, press switch j
past the point of resistance again
and release.
If the window still does not close
without an object having been trapped,
then hold the
j
switch down. The
side window will then close without the
obstruction sensor function.
iIf the driver’s window cannot be auto-
matically closed without an object
having been trapped, press the
j

switch past the point of resistance
again within five seconds and release.
The side windows will now close with-
out the obstruction sensor function.
Warning!
G
When closing the windows, make sure that
there is no danger of anyone being harmed
by the closing procedure.

149 Controls in detail
Driving systems
Parktronic system* (Parking assist)
The Parktronic system assists the driver
during parking maneuvers. It visually and
audibly indicates the distance between the
vehicle and an obstacle.
With the ignition on, Parktronic engages
automatically at speeds up to approxi-
mately 10 mph (15 km / h) and deactivates
during higher speeds.Parktronic monitors your vehicle’s environ-
ment by means of six sensors in the front
bumper and four sensors in the rear
bumper.
1Sensors located in front bumperWarning!
G
Parktronic is a supplemental system. It is
not intended to nor does it replace the need
for extreme care. The responsibility during
parking and other critical maneuvers rests
always with the driver.
Make sure that no persons or animals are lo-
cated in the area in which your are maneu-
vering. They could otherwise be injured.
Special attention must be paid to objects
with smooth surfaces or low silhouettes
(e.g. trailer couplings, painted posts, or
street curbs). Such objects may not be de-
tected by the system and can damage the
vehicle.
The operational function of the Parktronic
can be affected by dirty sensors, especially
at times of snow and ice. For notes on clean-
ing the Parktronic system sensors
(page 220).
Interference caused by other ultrasonic sig-
nals (e.g. working jackhammers or the air
brakes of trucks) can cause the system to
send erratic indications, and should be tak-
en into consideration.

150 Controls in detailDriving systemsMonitoring reach of sensors
The sensors must be free of dirt, ice and
snow or they will be unable to function
properly. Clean the sensors regularly with-
out scratching or damaging them.Front sensors
Rear sensors
Minimum distance
When an obstacle is located in this area, all
warning displays will light up and a warning
tone will sound. If the vehicle moves closer
than the minimum distance to an object,
the distance may no longer be displayed.Warning indicators
The warning indicators show the distance
between the sensor and the obstacle. The
warning indicators for the front area are lo-
cated above the center air outlets in the
dashboard. The warning indicator for the
rear area is located in the rear passenger
compartment lamp.
1Segments, left side of vehicle
2Segments, right side of vehicle
Each warning indicator has 6 yellow and 2
red segments.
Center
40 in (100 cm)
Corner
24 in (60 cm)
Center
48 in (120 cm)
Corner
32 in (80 cm)
Center
6 in (15 cm)
Corner
8 in (20 cm)

151 Controls in detail
Driving systems
The selector lever position determines
which warning indicator is activated.
As soon as the sensors detect an obstacle,
one or more segments light up, depending
on the distance. An intermittent acoustic
warning will also sound as the seventh seg-
ment lights up and a constant acoustic
warning lasting a maximum of 3 seconds
will sound for the eighth segment.Switching Parktronic on/off
You can switch Parktronic off manually.
The switch is located on the lower part of
the center console.
1Switching off
2Indicator lamp
3Switching onSwitching Parktronic off

Press switch on the upper part1.
Indicator lamp2 lights up.
Switching Parktronic on

Press switch on the upper part3.
The indicator lamp2 goes out.
Selector lever
position
Warning indicator
D
Front area activated
R
Rear area activated
N or P
No area activated
!If all red segments light up in the warn-
ing indicators, a dirty sensor or a ultra-
sonic signal could be the reason.

Clean the sensors (
page 220).
After cleaning the sensors, switch
the ignition on.
!If Parktronic is malfunctioning, all red
segments of the warning indicators
light up and an additional warning
sounds.
Contact your Mercedes-Benz Light
Truck Center as soon as possible.
iIf you switch the ignition on, Parktronic
will be automatically switched on.
The rear Parktronic sensors will not au-
tomatically disengage when towing a
trailer. Therefore switch Parktronic off.

198 OperationDriving instructionsCatalytic converter
Your Mercedes-Benz is equipped with
monolithic type catalytic converters, an
important element in conjunction with the
oxygen sensors to achieve substantial con-
trol of the pollutants in the exhaust emis-
sions. Keep your vehicle in proper
operating condition by following our rec-
ommended maintenance instructions as
outlined in your Service Booklet.
Emission control
Certain engine systems serve to keep the
toxic components of the exhaust gases
within permissible legal limits.
These systems, of course, will function
properly only when maintained strictly ac-
cording to factory specifications. Any ad-
justments on the engine should, therefore,
be carried out only by qualified
Mercedes-Benz Light Truck Center autho-
rized technicians. Engine adjustments
should not be altered in any way. More-
over, the specified service jobs must be carried out regularly according to
Mercedes-Benz servicing requirements.
For details refer to the Service Booklet.
!To prevent damage to the catalytic con-
verters, use only premium unleaded
gasoline in this vehicle.
Any noticeable irregularities in engine
operation should be repaired promptly.
Otherwise, excessive unburned fuel
may reach the catalytic converter,
causing it to overheat and start a fire.
Warning!
G
As with any vehicle, do not idle, park or op-
erate this vehicle in areas where combusti-
ble materials such as grass, hay or leaves
can come into contact with the hot exhaust
system, as these materials could be ignited
and cause a vehicle fire.
Warning!
G
Inhalation of exhaust gas is hazardous to
your health. All exhaust gas contains carbon
monoxide, and inhaling it can cause uncon-
sciousness and lead to death.
Do not run the engine in confined areas
(such as a garage) which are not properly
ventilated. If you think that exhaust gas
fumes are entering the vehicle while driving,
have the cause determined and corrected
immediately. If you must drive under these
conditions, drive only with at least one win-
dow fully open at all times.

220 OperationVehicle careOrnamental moldings
For regular cleaning and care of very dirty
chrome-plated parts, use a chrome clean-
er.
Headlamps, tail lamps, turn signal
lenses
Use a mild car wash detergent, such as
Mercedes-Benz approved Car Shampoo,
with plenty of water.
To prevent scratches, never apply strong
force and use only a soft, non-scratchy
cloth when cleaning the lenses. Do not at-
tempt to wipe dirty lenses with a dry cloth
or sponge.Cleaning the Parktronic* system
sensor
1Parktronic system sensor
Use a mild car wash detergent, such as
Mercedes-Benz approved Car Shampoo,
with plenty of water to clean the sensor1.
When using a steam cleaner or power
washer, aim nozzle only briefly from a min-
imum distance of 4 in. (10 cm) at
sensors1.
To prevent scratches, never apply strong
force and use only a soft, non-scratchy
cloth when cleaning the sensor. Do not at-
tempt to wipe dirty sensors with a dry cloth
or sponge.Wiper blades
Clean the wiper blade inserts with a clean
cloth and detergent solution.
Window cleaning
Use a window cleaning solution on all glass
surfaces. An automotive glass cleaner is
recommended.
iFor safety reasons, remove key from
steering lock before cleaning the wiper
blades, otherwise the wiper motor can
suddenly turn on and cause injury.iFor safety reasons, switch off wipers
and remove key from steering lock be-
fore cleaning the windshield, otherwise
the wiper motor can suddenly turn on
and cause injury.

293 Technical terms
ABS
(A
ntilock B
rake S
ystem)
Prevents the wheels from locking up
during braking so that the vehicle can
continue to be steered.
BabySmart
TM
airbag deactivation
system
This system detects if a special system
compatible child restraint seat is in-
stalled on the front passenger seat. The
system will automatically deactivate
the passenger front airbag when such a
seat is properly installed (indicator
lamp
7
in the instrument cluster
lights up). See your authorized
Mercedes-Benz Light Truck Center for
availability.
BabySmartTM
compatible child seats
Special restraint system for children.
The sensor system for the passenger
seat prevents deployment of the pas-
senger front airbag if a BabySmart
TM
compatible child seat is installed.BAS
(B
rake A
ssist S
ystem)
System for potentially reducing braking
distances in emergency braking situa-
tions. The system is activated when it
senses an emergency based on how
fast the brake is applied.
Bi-Xenon headlamps*
Headlamps which use an electric arc as
the light source and produce a more in-
tense light than filament headlamps.
Bi-Xenon headlamps produce low
beam and high beam.
CAC
(C
ustomer A
ssistance C
enter)
Mercedes-Benz customer service cen-
ter, which can help you with any ques-
tions about your vehicle and provide
assistance in the event of a break-
down.CAN system
(C
ontroller A
rea N
etwork)
Data bus network serving to control ve-
hicle functions such as door locking or
windshield wiping.
Cockpit
All instruments, switches, buttons and
indicator/warning lamps in the passen-
ger compartment needed for vehicle
operation and monitoring.
Cruise control
Driving convenience system for auto-
matically maintaining the vehicle speed
set by the driver.
Engine number
The number set by the manufacturer
and placed on the cylinder block to
uniquely identify each engine pro-
duced.

300 Index
Passenger 59
Safety guidelines 57
Side impact 59
Window curtain 59
Alarm
Audible 70, 79
Canceling 79
Visual 78
Alarm system
Anti-theft 78
Anticorrosion/antifreeze 288
Antiglare
Automatic 119
Antilock brake system (ABS) 293
Anti-theft alarm system
Arming 78
Canceling alarm 79
Disarming 79
Anti-theft systems
Anti-theft alarm system 78
Immobilizer 78
Tow-away alarm, glass breakage
sensor 79
Aquaplaning see Hydroplaning 183Armrest
Storage compartment in front of 153
Storage spaces 153
Armrest in rear seat bench 155
Ashtray
Front center console 156
Rear center console 157
At the gas station 200
ATF (automatic transmission fluid) 206
Attaching a trailer 194
Automatic antiglare for rear
view mirror 119
Automatic central locking
Activating 89
Deactivating 89
Automatic climate control 124
Adjusting air distribution 127
Adjusting air volume 127
Air conditioning 129
Air outlets 132
Air recirculation mode 128
Basic setting 127
Changing basic setting 127
Defrosting 128Economy mode 125
Rear passenger compartment 131
Rear window defroster 131
Residual heat utilization 130
Residual ventilation 130
Switching off 127
Switching on 126
Automatic headlamp mode 103
Automatic interior lighting control
Activating 107
Deactivating 107
Automatic locking when driving 89
Automatic transmission 113
Accelerator position 117
Emergency operation (Limp Home
Mode) 117
Gear ranges 114
Gear selector lever position 115
Gear shifting malfunctions 117
Kickdown 117
Manual shifting 113
One-touch gearshifting 113
Selector lever position 113
Towing a trailer 117
Transmission fluid 206

306 Index
Gasoline additives 287
Premium unleaded gasoline 200, 286
Requirements 287
Reserve warning 25
Fuel additives 287
Fuel filler flap 200
Locking 200
Opening 244
Unlocking 200
Fuel requirements 287
Fuel tank
Filler flap 200
Fuels, coolants, lubricants etc. 284
Functions
Trip computer 172
Fuse box 271, 272
Fuse chart 271
Fuses 271
Fuse box in engine compartment 271
Fuse box in passenger footwell 272
Fuse chart 271
Fuse extractor 271
Spare fuses 271G
Garage door opener 29, 168
Erasing in remote control 171
Integrated remote control 169
Rolling code programming 170
Gasoline see Fuel 200
Gasoline additives 287
Gauge for
Coolant temperature 25
Fuel 25
Outside temperature 25
Gear range 294
Automatic transmission 114
Limiting 114
Shifting into optimal 114
Gear range limit
Canceling 114
Gear selector lever
Cleaning 221
Position 115
Glass breakage sensor 79
Global Positioning System (GPS) 294
Glossary 293Glove box 23, 152
Closing 152
Opening 152
Good visibility 119
GPS 294
H
Hand-held transmitter
Programming integrated remote con-
trol 169
Hard plastic trim items
Cleaning 221
Hazard warning flasher 106
Switching off 106
Switching on 106
Head restraint
Installing 92
Removing 92
Head restraints
Manual seats 36
Power seats* 37
Headlamp aim
Adjusting 253
Headlamp cleaning system* 208