check oil MERCEDES-BENZ ML63AMG 2007 W163 Comand Manual

360 OperationEngine compartment
Have excess oil siphoned or drained
off. Contact an authorized
Mercedes-Benz Light Truck Center.
For more information on messages in the
multifunction display concerning engine
oil, see “Practical hints” (
page 413).
Checking engine oil level with the oil
dipstick (except ML 500)
When checking the oil level


the vehicle must be parked on level
ground


the vehicle must have been stationary
for at least 5 minutes with the engine
turned off1Oil dipstick
2Upper mark
3Lower mark

Open the hood (
page 356).

Pull out oil dipstick1.

Wipe oil dipstick1 clean.

Fully insert oil dipstick1 into the
dipstick guide tube.

Pull out oil dipstick1 again after
approximately 3 seconds to obtain
accurate reading.
The oil level is correct when it is be-
tween lower mark3 (min.) and upper
mark2 (max.) of the oil dipstick.

If necessary, add engine oil
(page 361).
For more information on engine oil, see
“Technical data” section (
page 543) and
(
page 546).
!
Excess oil must be siphoned or drained off.
It could cause damage to the engine and/or
catalytic converter (gasoline engine) or the oxi-
dation catalyst (diesel engine) not covered by
the Mercedes-Benz Limited Warranty.
i
All models (except ML 63 AMG):
The filling quantity between the upper and lower
marks on the oil dipstick is approximately
2.1 US qt. (2.0 l).
ML 63 AMG:
The filling quantity between the upper and lower
marks on the oil dipstick is approximately
1.6 US qt. (1.5 l).

403 Operation
Maintenance
Calling up the maintenance service indicator display
You can call up the maintenance service in-
dicator display at any time to check when
the next maintenance service is due.
Switch on the ignition (
page 40).

Press buttonè orÿ on the mul-
tifunction steering wheel repeatedly
until the standard display appears in
the multifunction display (
page 154).

Press buttonk orj until the
maintenance service indicator display
with the service symbol9 and the
service deadline appears in the multi-
function display.Resetting the maintenance service
indicator
In the event that the maintenance service
on your vehicle is not carried out by an
authorized Mercedes-Benz Light Truck
Center, you can have the maintenance
service indicator reset. The automotive
maintenance facility carrying out the
maintenance service will find the informa-
tion for resetting the maintenance service
indicator in the maintenance-relevant
information for your vehicle. Such informa-
tion is available from either your
authorized Mercedes-Benz Light Truck
Center or directly from Mercedes-Benz.
i
If the battery is disconnected, the days of
disconnection will not be included in the count
shown by the maintenance service indicator.To arrive at the true maintenance service dead-
line, you will need to subtract these days from
the days shown in the maintenance service indi-
cator message or maintenance service indicator
display.
Do not confuse the maintenance service indica-
tor with the engine oil level indicatorN.
i
If the maintenance service indicator was
inadvertently reset, have an authorized
Mercedes-Benz Light Truck Center correct it.
Only reset if the proper maintenance service has
been performed. Resetting the system without
performing the proper service as called for by
the maintenance service indicator will result in
engine damage and/or other vehicle damage not
covered by the Mercedes-Benz Limited
Warranty.

404 OperationVehicle careCleaning and care of the vehicle
Regular and proper care will help to
maintain the value of your vehicle. The
best way to protect your vehicle from
harmful environmental influences is to
wash it and use protective treatments
regularly.While in operation, even while parked, your
vehicle is subjected to varying external in-
fluences which, if gone unchecked, can at-
tack the paintwork as well as the
underbody and cause lasting damage.
Such damage is caused not only by
extreme and varying climatic conditions,
but also by:


Air pollution


Road salt


Tar


Gravel and stone chipping
To avoid paint damage, you should
immediately remove:


Grease and oil


Fuel


Coolant


Brake fluid


Bird droppings


Insects


Tree resins, etc.Frequent washing reduces and/or
eliminates the aggressiveness and
potency of the above adverse influences.
More frequent washings are necessary to
deal with unfavorable conditions:


near the ocean


in industrial areas (smoke, exhaust
emissions)


during winter operation
You should check your vehicle from time to
time for stone chipping or other damage.
Any damage should be repaired as soon as
possible to prevent corrosion.
In doing so, do not neglect the underbody
of the vehicle. A prerequisite for a thor-
ough check is a washing of the underbody
followed by a thorough inspection. Dam-
aged areas need to be re-undercoated.
Warning!
G
Many cleaning products can be hazardous.
Some are poisonous, others are flammable.
Always follow the instructions on the partic-
ular container. Always open your vehicle’s
doors or windows when cleaning the inside.
Never use fluids or solvents that are not de-
signed for cleaning your vehicle.
Always lock away cleaning products and
keep them out of reach of children.

453 Practical hints
What to do if …
When the message
Add 1 qt. engine oil
at next refueling (Canada:
1 liter
)
appears while the engine is running and at
operating temperature, the engine oil level
has dropped to approximately the mini-
mum level.
When this occurs, the warning will first
come on intermittently and then stay on if
the oil level drops further.Visually check for oil leaks. If no obvious oil
leaks are noted, drive to the nearest
service station where the engine oil should
be topped to the required level with an ap-
proved oil specified in the Factory
Approved Service Products pamphlet.
Display symbol
Display messages
Possible cause/consequence
Possible solution
N
Check eng. oil level
at next refueling
The engine oil level is too low.

Check the engine oil level (
page 360)
(except ML 500), or (
page 358)
(ML 500 only).
USA only:Add 1 qt. engine oil
at next refuelingCanada only:Add 1 liter engine oil
at next refueling
The engine oil level is too low.

Add engine oil (
page 361) and check
the engine oil level (page 360) (except
ML 500), or (
page 358) (ML 500 only).
Engine oil level
cannot be measured
The measuring system is
malfunctioning.

Have the measuring system checked by
an authorized Mercedes-Benz Light Truck
Center.

454 Practical hintsWhat to do if …Display symbol
Display messages
Possible cause/conse-
quence
Possible solution
N
Engine oil level
Stop car, turn engine off
There is no oil in the engine.
There is a danger of engine
damage.

Carefully bring the vehicle to a halt as soon as
it is safe to do so in a safe location.

Turn off the engine.

Add engine oil (
page 361) and check the en-
gine oil level (
page 360) (except ML 500), or
(
page 358) (ML 500 only).
Engine oil level
Reduce oil level
You have added too much
engine oil. There is a risk of
damaging the engine and/or
the catalytic converter (gaso-
line engine) or the oxidation
catalyst (diesel engine).

Have oil siphoned or drained off.
Observe all legal requirements with respect to
its disposal.
Engine oil level
Visit workshop
The engine oil has dropped to
a critical level.

Check the engine oil level (
page 360) (except
ML 500), or (
page 358) (ML 500 only) and
add oil as required (
page 361).

If you must add engine oil frequently, have the
engine checked for possible leaks.
!
The engine oil level warnings should not be
ignored. Extended driving with the symbol dis-
played could result in serious engine damagethat is not covered by the Mercedes-Benz
Limited Warranty.

484 Practical hintsReplacing bulbs
Notes on bulb replacement

Only use 12-volt bulbs of the same type
and with the specified watt rating.


Switch lights off before changing a bulb
to prevent short circuits.


Always use a clean lint-free cloth when
handling bulbs.


Your hands should be dry and free of oil
and grease.


If the newly installed bulb does not
come on, visit an authorized
Mercedes-Benz Light Truck Center.Have the LEDs and bulbs for the following
lamps replaced by an authorized
Mercedes-Benz Light Truck Center:


the additional turn signal lamps in the
exterior rear view mirrors


the high mounted brake lamp


the Bi-Xenon* low beam lamps


the Bi-Xenon high beam flasher spot-
light*
Warning!
G
Bulbs and bulb sockets can be very hot.
Allow the lamp to cool down before chang-
ing a bulb.
Keep bulbs out of reach of children.
Halogen lamps contain pressurized gas.
A bulb can explode if you:

touch or move it when hot


drop the bulb


scratch the bulb
Wear eye and hand protection.
Because of high voltage in Xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.
!
Do not replace the LEDs yourself. You could
otherwise damage the LEDs or parts of the vehi-
cle. Only have the LEDs replaced by a qualified
specialist workshop having the necessary skills
and tools for carrying out the work required.
i
Replacing the bulbs for the front lamps is a
technically complex process. For your conve-
nience, we recommend that you have this work
carried out by an authorized Mercedes-Benz
Light Truck Center.
Have the headlamp adjustment checked
regularly.

548 Technical dataFuels, coolants, lubricantsIn areas where carbon deposits may be
encountered due to lack of availability of
gasolines which contain these additives,
Mercedes-Benz recommends the use of
additives approved by us for use on
Mercedes-Benz vehicles. Refer to Factory
Approved Service Products pamphlet for a
listing of approved product(s). Follow
directions on product label.
Do not blend other fuel additives with fuel.
This only results in unnecessary costs and
may be harmful to the engine operation.
Damage or malfunction resulting from
poor fuel quality or from blending addition-
al fuel additives other than those tested
and approved by us for use on
Mercedes-Benz vehicles listed in the
Factory Approved Service Products
pamphlet are not covered by the
Mercedes-Benz Limited Warranty.
Fuel requirements
Gasoline engine
Only use premium unleaded fuel.

The octane number (posted at the
pump) must be 91 min. It is an average
of both the Research (R) octane num-
ber and the Motor (M) octane number:
(R+M) /2). This is also known as the
ANTI-KNOCK INDEX.
Unleaded gasoline containing oxygenates
such as ethanol, IPA, IBA and TBA can be
used provided the ratio of any one of these
oxygenates to gasoline does not
exceed 10%; MTBE must not exceed 15%.
The ratio of methanol to gasoline must not
exceed 3% plus additional cosolvents.
Using mixtures of ethanol and methanol is
not allowed. Gasohol, which contains
10% ethanol and 90% unleaded gasoline,
can be used.These blends must also meet all other fuel
requirements, such as resistance to spark
knock, boiling range, vapor pressure, etc.
Diesel engine
Only use commercially available vehicular
diesel fuels No. 2 or No. 1 (ASTM D975 No.
2-D or No. 1-D).
To prevent malfunctions, diesel fuel with
improved cold flow characteristics is of-
fered in the winter months. Check with
your fuel retailer.
!
Do not fill the tank with gasoline. Do not
blend diesel fuel with gasoline or kerosine. The
fuel system and engine will otherwise be dam-
aged, which is not covered by the
Mercedes-Benz Limited Warranty.

549 Technical data
Fuels, coolants, lubricants
Coolants
The engine coolant is a mixture of water
and anticorrosion/antifreeze, which
provides:

Corrosion protection


Freeze protection


Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory
with a coolant providing freeze protection
to approximately -35°F (-37°C) and corro-
sion protection.If the antifreeze mixture is effective to
-22°F (-30°C), the boiling point of the cool-
ant in the pressurized cooling system is
reached at approximately 266°F (130°C).
The coolant solution must be used year
round to provide the necessary corrosion
protection and increase boil-over protec-
tion. Refer to Maintenance Booklet for
replacement interval.
Coolant system design and coolant used
determine the replacement interval. The
replacement interval published in the
Maintenance booklet is only applicable if
MB 325.0 anticorrosion/antifreeze solu-
tion or other Mercedes-Benz approved
products of equal specification (see
Factory Approved Service Products
pamphlet) are used to renew the coolant
concentration or bring it back up to the
proper level.To provide important corrosion protection,
the solution must be at least 45% anticor-
rosion/antifreeze (equivalent to freeze
protection to approx. - 22°F [-30°C]). If
you use a solution that is more than 55%
anticorrosion/antifreeze (freeze protec-
tion to approx. - 49°F [-45°C]), the engine
temperature will increase due to the lower
heat transfer capability of the solution.
Therefore, do not use more than this
amount of anticorrosion/antifreeze.
If the coolant level is low, water and
MB 325.0 anticorrosion/antifreeze should
be used to bring it up to the proper level
(have cooling system checked for signs of
leakage). Please make sure the mixture is
in accordance with label instructions.
The water in the cooling system must meet
minimum requirements, which are usually
satisfied by normal drinking water. If you
are not sure about the water quality, con-
sult an authorized Mercedes-Benz Light
Truck Center.
!
Add premixed coolant solution only. Adding
water and MB 325.0 Anticorrosion/Antifreeze
separately from each other, could cause engine
damage not covered by the
Mercedes-Benz Limited Warranty.

559 Index
Emergency operations
Remote door unlock, Tele Aid* 315
Unlocking/opening the tailgate 476
Emergency Tensioning Device see ETD
Emergency, In case of
Battery, Jump starting 515
Engine shut-down 525
First aid kit 469
Flat tire 497
Fuses 522
Hazard warning flasher 142
Instrument cluster, Indicator
lamps 414, 415, 416, 417, 418,
419, 420, 421, 422, 423, 424
Roadside Assistance 12, 312
Towing the vehicle 518
Emission control 350
Information label 531
System warranties 10
Vacuum line routing diagram
label 531Engine
Belt layout (ML 320 CDI) 532
Belt layout (ML 350) 532
Belt layout (ML 500) 532
Belt layout (ML 63 AMG) 533
Block heater (Canada only) 400
Break-in recommendations 358
Cleaning 406
Compartment 356
Emergency engine shut-down 525
Malfunction indicator lamp 29, 449
Maximum engine speed 146, 534,
535
Messages in the
multifunction display 449
Number 531
Starting 54
Starting with KEYLESS-GO* 55
Starting with the SmartKey 55
Tachometer 29, 146
Technical data 534
Turning off with KEYLESS-GO* 67
Turning off with the SmartKey 67Engine coolant see Coolant
Engine oil 358, 546
Adding 361, 546
Additives 546
Changing 361, 546
Checking level 358
Checking level with the
control system (ML 500 only) 358
Checking with the oil dipstick
(except ML 500) 360
Consumption 358
Filler neck (ML 350, ML 320 CDI) 361
Filler neck (ML 500, ML 63 AMG) 361
Messages in display 359, 453
Messages in the
multifunction display 453
Recommended engine oils
and oil filters 546
Engine oil level 358
ESP
®
27, 98
Four wheel electronic traction system
with ESP
®
98
Messages in the
multifunction display 436, 437
Off-road-ESP®
101
Warning lamp 27, 419, 420

566 IndexMON 353, 548
Multicontour seat* 130
Multifunction display 147
Changing settings see Control
system menus and Control system
submenus
Selecting display 168
Selecting language 167
Multifunction display messages 428
ABS 430
Air suspension package* 467
Brake fluid 449
Brake lamps 458
Brake pads 447
Check engine 449
Coolant 452
Cruise control 431
Distronic* 432
Doors 455
Downhill Speed Regulation 447
EBP 448
Engine coolant 450, 452
Engine oil 453
ESP
®
419Fog lamps, Front 458
Fog lamps, Rear 461
Front passenger front air bag 440,
441, 442, 443
Fuel cap 455
Gear selector lever 438
Headlamps 458, 460, 461, 463
Hood 455
Key, SmartKey 457
Key, SmartKey with
KEYLESS-GO* 456, 457
Lamps 458, 460, 461, 463
Low tire pressure 444, 465, 466
Parking brake 438, 448
Parking lamps 459
Tele Aid* 464
Telephone* 464
Turn signals 463
Vehicle battery 446
Windshield washer fluid 464
Multifunction steering wheel 30, 148
Button operation 148N
Navigation system* 161
See separate COMAND system
operating instructions
Net, Parcel 297
Net, Partition* 287
Neutral gear position, Automatic
transmission 185, 189
New vehicle, Break-in period 324
Night security illumination 139, 172
Normal occupant weight 396
Number, Vehicle Identification (VIN) 530
O
Occupant distribution 396
Occupant safety 70
Active head restraint 80
Air bags 71
Children and air bags 73, 82, 84
Children in the vehicle 82
Fastening the seat belt 51
Front passenger front air bag off
indicator lamp 86, 89, 90
Infant and child restraint systems 82