adding oil MERCEDES-BENZ ML63AMG 2007 W163 Comand Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2007, Model line: ML63AMG, Model: MERCEDES-BENZ ML63AMG 2007 W163Pages: 585
Page 360 of 585
359 Operation
Engine compartment
Press buttonk orj on the
multifunction steering wheel until the
following message appears in the mul-
tifunction display:
One of the following messages will
subsequently appear in the
multifunction display:
Engine oil level OK
Add 1.0 qt. to reach max. oil
level(Canada:
1.0 liter
)
Add 1.5 qts. to reach max. oil
level(Canada:
1.5 liters
)
Add 2.0 qts. to reach max. oil
level(Canada:
2.0 liters
)
If necessary, add engine oil
(page 361).
For information on adding engine oil, see
(
page 361).
For more information on engine oil, see
“Technical data” section (
page 543) and
(
page 546).
Other display messages
If the SmartKey or KEYLESS-GO*
start/stop button is not in position2, the
following message will appear:
Switch ignition on
to check engine oil level
Switch on the ignition (
page 40).
If you see the message:
Observe waiting period
If the engine is at operating
temperature, wait 5 minutes before
repeating check procedure.
If the engine is not at operating temper-
ature, wait 30 minutes before repeat-
ing check procedure.
If you see the message:
Engine oil level
Not when engine on
Turn off the engine.
If the engine is at operating tempera-
ture, wait 5 minutes before checking
oil.
If the engine is not at operating temper-
ature yet, you must wait 30 minutes
before checking oil.
If there is excess engine oil with the engine
at operating temperature, the following
message will appear:
Engine oil level
Reduce oil level
i
If you want to interrupt the checking proce-
dure, press the
k
or
j
button on the
multifunction steering wheel.
Page 362 of 585
361 Operation
Engine compartment
Adding engine oil
Example ML 350 (ML 320 CDI similar)1Filler capExample ML 500 (ML 63 AMG similar)1Filler cap
Unscrew filler cap1 from filler neck.
Add engine oil as required. Never over-
fill with oil.
Be careful not to spill any oil when adding.
Avoid environmental damage caused by oil
entering the ground or water.
Screw filler cap1 back on filler neck.
For more information on engine oil, see
“Technical data” section (
page 543) and
(
page 546).
!
Only use approved engine oils and oil filters
required for vehicles with Maintenance System
(U.S. vehicles) or FSS PLUS (Canada vehicles).
For a listing of approved engine oils and oil
filters, refer to the Factory Approved Service
Products pamphlet in your vehicle literature
portfolio, or contact an authorized
Mercedes-Benz Light Truck Center.
Using engine oils and oil filters of specification
other than those expressly required for the
Maintenance System (U.S. vehicles) or
FSS PLUS (Canada vehicles), or changing of oil
and oil filter at change intervals longer than
those called for by the Maintenance System
(U.S. vehicles) or FSS PLUS (Canada vehicles)
will result in engine or emission control system
damage not covered by the Mercedes-Benz
Limited Warranty.
!
Excess oil must be siphoned or drained off.
It could cause damage to the engine and/or
catalytic converter (gasoline engine) or the oxi-
dation catalyst (diesel engine) not covered by
the Mercedes-Benz Limited Warranty.
Page 550 of 585
549 Technical data
Fuels, coolants, lubricants
Coolants
The engine coolant is a mixture of water
and anticorrosion/antifreeze, which
provides:
Corrosion protection
Freeze protection
Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory
with a coolant providing freeze protection
to approximately -35°F (-37°C) and corro-
sion protection.If the antifreeze mixture is effective to
-22°F (-30°C), the boiling point of the cool-
ant in the pressurized cooling system is
reached at approximately 266°F (130°C).
The coolant solution must be used year
round to provide the necessary corrosion
protection and increase boil-over protec-
tion. Refer to Maintenance Booklet for
replacement interval.
Coolant system design and coolant used
determine the replacement interval. The
replacement interval published in the
Maintenance booklet is only applicable if
MB 325.0 anticorrosion/antifreeze solu-
tion or other Mercedes-Benz approved
products of equal specification (see
Factory Approved Service Products
pamphlet) are used to renew the coolant
concentration or bring it back up to the
proper level.To provide important corrosion protection,
the solution must be at least 45% anticor-
rosion/antifreeze (equivalent to freeze
protection to approx. - 22°F [-30°C]). If
you use a solution that is more than 55%
anticorrosion/antifreeze (freeze protec-
tion to approx. - 49°F [-45°C]), the engine
temperature will increase due to the lower
heat transfer capability of the solution.
Therefore, do not use more than this
amount of anticorrosion/antifreeze.
If the coolant level is low, water and
MB 325.0 anticorrosion/antifreeze should
be used to bring it up to the proper level
(have cooling system checked for signs of
leakage). Please make sure the mixture is
in accordance with label instructions.
The water in the cooling system must meet
minimum requirements, which are usually
satisfied by normal drinking water. If you
are not sure about the water quality, con-
sult an authorized Mercedes-Benz Light
Truck Center.
!
Add premixed coolant solution only. Adding
water and MB 325.0 Anticorrosion/Antifreeze
separately from each other, could cause engine
damage not covered by the
Mercedes-Benz Limited Warranty.
Page 560 of 585
559 Index
Emergency operations
Remote door unlock, Tele Aid* 315
Unlocking/opening the tailgate 476
Emergency Tensioning Device see ETD
Emergency, In case of
Battery, Jump starting 515
Engine shut-down 525
First aid kit 469
Flat tire 497
Fuses 522
Hazard warning flasher 142
Instrument cluster, Indicator
lamps 414, 415, 416, 417, 418,
419, 420, 421, 422, 423, 424
Roadside Assistance 12, 312
Towing the vehicle 518
Emission control 350
Information label 531
System warranties 10
Vacuum line routing diagram
label 531Engine
Belt layout (ML 320 CDI) 532
Belt layout (ML 350) 532
Belt layout (ML 500) 532
Belt layout (ML 63 AMG) 533
Block heater (Canada only) 400
Break-in recommendations 358
Cleaning 406
Compartment 356
Emergency engine shut-down 525
Malfunction indicator lamp 29, 449
Maximum engine speed 146, 534,
535
Messages in the
multifunction display 449
Number 531
Starting 54
Starting with KEYLESS-GO* 55
Starting with the SmartKey 55
Tachometer 29, 146
Technical data 534
Turning off with KEYLESS-GO* 67
Turning off with the SmartKey 67Engine coolant see Coolant
Engine oil 358, 546
Adding 361, 546
Additives 546
Changing 361, 546
Checking level 358
Checking level with the
control system (ML 500 only) 358
Checking with the oil dipstick
(except ML 500) 360
Consumption 358
Filler neck (ML 350, ML 320 CDI) 361
Filler neck (ML 500, ML 63 AMG) 361
Messages in display 359, 453
Messages in the
multifunction display 453
Recommended engine oils
and oil filters 546
Engine oil level 358
ESP
®
27, 98
Four wheel electronic traction system
with ESP
®
98
Messages in the
multifunction display 436, 437
Off-road-ESP®
101
Warning lamp 27, 419, 420