remote start MERCEDES-BENZ R320 2008 W251 Owner's Manual

39 Getting started
Unlocking
Unlocking with KEYLESS-GO*
With the KEYLESS-GO function, you can
lock or unlock the vehicle without using
the remote control buttons on the
SmartKey and start the engine without
inserting the SmartKey into the starter
switch.Grasp an outside door handle.
All turn signal lamps flash once. The
vehicle unlocks. The locking knobs in
the doors move up. The anti-theft alarm
system is disarmed. The locator light-
ing comes on if the feature is enabled
in the control system (
page 178).
Enter the vehicle.
For more information, see “SmartKey with
KEYLESS-GO*” (
page 113).
Starter switch positions
iTo unlock the vehicle, the SmartKey with
KEYLESS-GO must be outside the vehicle, no
further than approximately 3 feet (1 meter) away
from the respective door.
Warning!G
When leaving the vehicle, always take the
SmartKey with KEYLESS-GO* with you, and
lock the vehicle. Do not leave children
unattended in the vehicle, or with access to
an unlocked vehicle. A child’s unsupervised
access to a vehicle could result in an
accident and/or serious personal injury.
i If the vehicle has been parked for more than
72 hours, you must pull an outside door handle
in order to activate the KEYLESS-GO function.
Warning!G
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you and
lock the vehicle. Do not leave children
unattended in the vehicle, or with access to
an unlocked vehicle. A child’s unsupervised
access to a vehicle could result in an
accident and/or serious personal injury.

110 Controls in detail
In the “Controls in detail” section you will
find detailed information on how to oper-
ate the equipment installed in your vehicle.
If you are already familiar with the basic
functions of your vehicle, this section will
be of particular interest to you.
To quickly familiarize yourself with the ba-
sic functions of the vehicle, refer to the
“Getting started” section of this manual.
The corresponding page numbers are
given at the beginning of each segment.
Locking and unlocking
For more information on locking and un-
locking, see the “Getting started” section
(
page 38) and (page 67).
SmartKey
Your vehicle comes supplied with two
SmartKeys, each with remote control and
a removable mechanical key.
The SmartKey provides an extended oper-
ating range. To prevent theft, however, it is
advisable to only unlock the vehicle when
you are in close proximity to it.
The SmartKey centrally locks and unlocks:

the doors

the tailgate

the fuel filler flap
SmartKey with remote control
1‹Lock button
2ŠUnlock button* for tailgate
3Locking tab for mechanical key
4ŒUnlock button
5Battery check lamp
6ÂPanic button (
page 98)

121 Controls in detail
Locking and unlocking
Closing the tailgate from the outside
manually
1Handle
Lower tailgate by pulling firmly on
handle1.
Close tailgate with hands placed flat
on it.
Once the tailgate touches the latch,
the tailgate will pull itself shut automat-
ically.Power tailgate*
In vehicles with power tailgate, you can

open and close the tailgate from the
inside and the outside electrically

limit the opening height of the tailgate

interrupt the opening/closing proce-
dure at any time by

pressing or pulling the
door-mounted remote tailgate
switch (
page 122)

pressing the Šbutton on the
SmartKey (
page 110) or
SmartKey with KEYLESS-GO*
(
page 113)

pressing the tailgate closing switch
(
page 124)

pressing the tailgate
closing/locking switch (vehicles
with KEYLESS-GO*) (
page 125)
Warning!G
To prevent possible personal injury, always
keep hands and fingers away from the cargo
compartment opening when closing the
tailgate. Be especially careful when small
children are around.
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children
unattended in the vehicle, or with access to
an unlocked vehicle. A child’s unsupervised
access to a vehicle could result in an
accident and/or serious personal injury.
iTo prevent an inadvertent lockout, do not
place the SmartKey in the cargo compartment.
Vehicles with KEYLESS-GO*: To prevent a
possible inadvertent lockout, the tailgate will
open automatically if a SmartKey with
KEYLESS-GO is recognized inside the vehicle.iIf the vehicle was previously centrally locked
with the SmartKey or KEYLESS-GO*, the tailgate
will lock automatically after closing it. The turn
signals flash three times to confirm locking.
!The tailgate swings open upwards automat-
ically. Always make sure there is sufficient over-
head clearance.

123 Controls in detail
Locking and unlocking
Limiting opening height of tailgate*
In vehicles with power tailgate*, the tail-
gate opening height can be limited when
transporting goods on a roof rack*
(e.g. presence of an MB sport luggage
container*). When activated, the tailgate
opens to approximately 6.4 ft (1.95 m).
Activate the limiting opening height of
tailgate using the control system
(
page 183).
Closing the tailgate from the inside
You can close the tailgate from the inside
using the remote tailgate switch.
If the tailgate comes into contact with an
object while closing (e.g. luggage that has
been piled too high) the closing procedure
is stopped and the tailgate reopens.
Press remote tailgate switch1
(
page 122) until tailgate begins to
close.
The tailgate closes. While the tailgate is
closing an acoustic signal sounds.
To interrupt the closing procedure:
Press or pull remote tailgate switch1
(
page 122).
Warning!G
Maintain sight of the area around the rear of
the vehicle while operating the tailgate with
the door-mounted switch. Monitor the
closing procedure carefully to make sure no
one is in danger of being injured.
To interrupt the closing procedure, press or
pull the door-mounted remote tailgate
switch or press the Šbutton on the
SmartKey or SmartKey with KEYLESS-GO*.
Even with the SmartKey or the SmartKey
with KEYLESS-GO* removed from the
starter switch or the SmartKey with
KEYLESS-GO* removed from the vehicle,
the remote tailgate switch can be operated.
Therefore, do not leave children unattended
i n t h e v e h i c l e , o r w i t h a c c e s s t o a n u n l o c k e d
vehicle. A child’s unsupervised access to a
vehicle could result in an accident and/or
serious personal injury.

124 Controls in detail
Locking and unlocking
Closing the tailgate from the outside
You can close the tailgate from the outside
using the tailgate closing switch or
theŠbutton on the SmartKey or
SmartKey with KEYLESS-GO*.
In vehicles with KEYLESS-GO*, you can
also simultaneously lock the vehicle.
If the tailgate comes into contact with an
object while closing (e.g. luggage that has
been piled too high), the closing procedure
is stopped and the tailgate reopens.
Vehicles without KEYLESS-GO*
1Tailgate closing switch
Vehicles with KEYLESS-GO*
1Tailgate closing switch
Press tailgate closing switch1 or the
Šbutton on the SmartKey or
SmartKey with KEYLESS-GO* briefly.
The tailgate closes and an acoustic
warning sounds.
Warning!G
Monitor the closing procedure carefully to
make sure no one is in danger of being in-
jured. To prevent possible personal injury,
always keep hands and fingers away from
the cargo compartment opening when clos-
ing the tailgate. Be especially careful when
small children are around. To stop the clos-
ing procedure, do one of the following:

Press tailgate closing switch1
(
page 124).

Press KEYLESS-GO locking/closing
switch* 1 (
page 125).

Press the Šbutton on the SmartKey
(
page 110) or SmartKey with
KEYLESS-GO* (
page 113).

Press or pull the remote tailgate switch
on the driver’s door (
page 122).
Even with the SmartKey removed from the
starter switch or the SmartKey with
KEYLESS-GO* removed from the vehicle,
the tailgate closing switch can be operated.
Therefore, do not leave children unattended
in the vehicle, or with access to an unlocked
vehicle. A child’s unsupervised access to a
vehicle could result in an accident and/or
serious personal injury.

331 Controls in detail
Useful features
Step 3:
Hold the end of the hand-held remote
control5 of the device you wish to
train approximately 2 to 5 in
(5 to12 cm) away from the signal trans-
mitter button (2, 3 or4) to be pro-
grammed, while keeping indicator
lamp1 in view.
Step 4:
Using both hands, simultaneously
press hand-held remote control
button6 and the desired signal trans-
mitter button (2, 3 or4). Do not
release the buttons until step 5 is com-
pleted.
Indicator lamp1 will flash, first slowly
and then rapidly.Step 5:
After indicator lamp1 changes from a
slow to a rapidly flashing light, release
the hand-held remote control button
and the signal transmitter button.
Step 6:
Press and hold the just-trained signal
transmitter button (2, 3 or4) and
observe indicator lamp1.
If indicator lamp1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button (2, 3 or4) is pressed and
released.
Step 7:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.Rolling code programming
To train a garage door opener (or other
rolling code devices) with the rolling code
feature, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
Step 8:
Locate “training” button on the garage
door opener motor head unit.
Exact location and color of the button
may vary by garage door opener brand.
Depending on manufacturer, the
“training” button may also be referred
to as “learn”or “smart” button. If there
is difficulty locating the transmitting
button, refer to the garage door opener
Operator’s Manual.
iIndicator lamp1 flashes immediately the
first time the signal transmitter button is
programmed. If this button has already been
programmed, the indicator lamp will only start
flashing after 20 seconds.
iIf indicator lamp1 flashes rapidly for about
2 seconds and then turns to a constant light,
continue with programming steps 8 through 12
as your garage door opener may be equipped
with the “rolling code” feature.


332 Controls in detail
Useful features
Step 9:
Press the “training” button on the
garage door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the
following step.
Step 10:
Return to the vehicle and firmly
press, hold for 2 seconds and release
the programmed signal transmitter
button (2, 3 or4).
Step 11:
Press, hold for 2 seconds and release
same signal transmitter button a
second time to complete the training
process.Step 12:
Confirm the garage door operation by
pressing the programmed signal trans-
mitter button (2, 3 or4).
Step 13:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the
integrated signal transmitter to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:Step 4:
Press and hold the signal transmitter
button (2, 3 or4). Do not release
this button until it has been success-
fully trained.
While still holding down the signal
transmitter button (2, 3 or4),
“cycle” your hand-held remote control
button6 as follows: Press and hold
button6 for 2 seconds, then release
it for 2 seconds, and again press and
hold it for 2 seconds. Repeat this
sequence on the hand-held remote
control until the frequency signal has
been learned. Upon successful train-
ing, indicator lamp1 will flash slowly
and then rapidly after several seconds.
Proceed with programming step 5 and
step 6 to complete.
iSome garage door openers (or other rolling
code equipped devices) may require you to
press, hold for 2 seconds and release the same
signal transmitter button a third time to com-
plete the training process.


333 Controls in detail
Useful features
Reprogramming a single signal
transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:
Switch on the ignition (page 39).
Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.
Indicator lamp1 will begin to flash
after 20 seconds. Without releasing
the signal transmitter button, proceed
with programming starting with step 3.Operation of integrated remote control
Switch on the ignition (page 39).
Select and press the appropriate
integrated signal transmitter
button (2, 3 or4) to activate the
remote controlled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing the integrated remote control
memory
Switch on the ignition (page 39).
Simultaneously press and hold outer
signal transmitter buttons2 and 4,
for approximately 20 seconds, until the
indicator lamp1 flashes rapidly. Do
not hold for longer than 30 seconds.
The codes of all three channels are
erased.Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:

Check the frequency of the hand-held
remote control5 (typically located on
the reverse side of the remote).
The integrated remote control is com-
patible with radio-frequency devices
operating between 280-390 MHz.

Put a new battery in hand-held remote
control5. This will increase the likeli-
hood of the hand-held remote control
sending a faster and more accurate sig-
nal to the integrated remote control.

While performing step 3, hold
hand-held remote control5 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming.
Attempt varying angles at the distance
of 2 to 5 in (5 to 12 cm) away or the
same angle at varying distances.
iUpon completion of programming the
integrated remote control, make sure you retain
the hand-held remote control that came with the
garage door opener, gate operator or other
device. You may need it for use in other vehicles,
for future programming of an integrated
remote control, or simply for continued use as a
hand-held remote control to operate the respec-
tive device in other situations.
iIf you sell your vehicle, erase the codes of all
three channels.

549 Index
D
Date display, Setting 176
Daytime running lamp mode 145
Setting 177
Deep water see Standing water
Defogging windshield 216, 230
Defrosting, Front 214, 229
Defrosting, Rear 207
Delayed shut-off
Exterior lamps 179
Interior lighting 180
Department of Transportation see DOT
Diesel engine
Bleeding fuel system 502
Preglow indicator lamp 29
Diesel fuel see Fuel
Difficulties
While driving 62
With starting 55
Digital speedometer 157, 165
Dimensions, Vehicle 534
Direction of rotation (tires) 365Displays
Digital speedometer 157, 165
Distronic* (Canada only) 168, 265
Maintenance service indicator
message 400
Messages in the multifunction
display 427–466
Multifunction display 157
Outside temperature 155, 157, 165
Selecting 175
Showing malfunctions 169
Symbol messages 444
Text messages 429
Vehicle status message memory 169
Vehicle system settings, Control
system 161, 163, 170
Distance to empty (range), Trip
computer 185
Distance warning function* (Canada
only) 185Distronic* (Canada only) 262
Activating 268
Cleaning system sensor 407
Control system 267
Deactivating 271
Distance warning function* 275
Driving hints 273
Messages in the multifunction
display 431
Warning and indicator lamps 265
Door
Entry lamps 153
Locking, In an emergency 475
Locking/unlocking,
KEYLESS-GO* 113
Locking/unlocking, SmartKey 110
Messages in the multifunction
display 452
Opening from the inside 118
Opening from the outside 112
Remote door unlock (Tele Aid*) 328
Unlocking, Mechanical key 474
Door control panel 36
Door handle 36
Door windows see Power windows
DOT 388, 394

550 Index
Drinking and driving 339
Driving 50
Abroad 348
Hydroplaning 344
In winter 346, 398
Instructions 50, 339
Problems 62
Safety systems 99
Systems 257
Through standing water 347
With Distronic* 273
Driving off 56
Driving safety systems
ABS 99
BAS 101
EBP 105
ESP
®101
ETS/4-ETS 103
Driving systems 257
AIRMATIC* 276
Cruise control 257
Distronic* (Canada only) 262
Parktronic* 281
Rear view camera* 285
Driving tips 197
Kickdown 197E
Easy-entry/exit feature* 128
Control system 184
EBP 105
Indicator and warning lamps 416
Electric air pump 499
Electrical fuses see Fuses
Electrical system, Technical data 533
Electronic Brake Proportioning see EBP
Electronic Stability Program see ESP
®
Electronic Traction System see ETS/4-ETS
Emergency calls
Tele Aid* 323
Emergency, In case of
Battery, Jump starting 511
First aid kit 467
Flat tire 492
Fuses 518
Hazard warning flasher 150
Instrument cluster, Indicator
lamps 414–422
Roadside Assistance 12, 325
Towing the vehicle 513Emergency operation
Locking/unlocking the vehicle 474
Remote door unlock, Tele Aid* 328
Tailgate, Opening from the
inside 120
Emergency operation (Limp-Home
Mode) 202
Emergency tensioning device see ETD
Emission control 350
Information label 525
System warranties 10
Engine
Belt layout 526
Break-in recommendations 338
Cleaning 405
Compartment 356
Malfunction indicator lamp 29, 417
Maximum engine speed 155, 527
Number 525
Starting 53
Tachometer 29, 155
Technical data 527
Turning off 66