display MERCEDES-BENZ R63AMG 2007 R171 Manual PDF
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2007, Model line: R63AMG, Model: MERCEDES-BENZ R63AMG 2007 R171Pages: 570
Page 241 of 570
240 Controls in detail
3-zone automatic climate control*
Windshield fogged on the outside
Switch the windshield wipers on
(
page 60).
Press buttonU (page 234).
AUTO appears in the displaye
(
page 234). Air volume and air
distribution are controlled separately
for each zone.
If the automatic air distribution and air
volume are switched off:
Press buttons8 and Y
(
page 234).
Maximum cooling MAX COOL
If the air distribution control as well as the
airflow volume control are set toU and
there is a high need for cooling, the
MAX COOL function is activated.
“
MAX COOL” appears in the front and rear
display.
This provides the fastest possible cooling
of the vehicle interior (when windows and
tilt/sliding sunroof* or tilt/sliding panel*
are closed).
Air recirculation mode
Switch to air recirculation mode to prevent
unpleasant odors from entering the vehicle
from the outside (e.g. before driving
through a tunnel). This setting cuts off the
intake of outside air and recirculates the
air in the passenger compartment.
iKeep this setting selected only until the
windshield is clear again.
Warning!G
Fogged windows impair visibility, endanger-
ing you and others. If the windows begin to
fog on the inside, switching off the air
recirculation mode immediately should clear
interior window fogging. If interior window
fogging persists, make sure the air
conditioning (
page 243) is activated, or
press button0.
Page 247 of 570
246 Controls in detail
3-zone automatic climate control*
Activating rear automatic climate
control
Press buttonU.
The indicator lamp on the button
comes on. The temperature, air
volume, and air distribution are ad-
justed automatically.
Deactivating rear automatic climate
control
Press button´.
The indicator lamp on the button goes
out.
The cooling function switches off after
a short delay.Operating from the front
Deactivating
Press button> (page 234).
The indicator lamp on the button
comes on.
In displaye (
page 234), you will see
the >symbol followed by
MODE for
approximately 3 seconds.
Press button´ (page 234).
In displaye (
page 234), you will see
the >symbol followed by
OFF.
The rear automatic climate control is
switched off.Reactivating
Press button> (page 234).
The indicator lamp on the button
comes on.
In displaye (
page 234), you will see
the >symbol followed by
ON and
MODE. The MODE display is cleared and
the indicator lamp on button>
goes out after approximately
3 seconds.
The rear automatic climate control
switches on.
iThe automatic climate control must be
switched on (
page 236).
iSwitch off the rear automatic climate
control for improved cooling or heating output in
the front passenger compartment.
You can also switch off the rear automatic
climate control from the front passenger com-
partment (
page 246).
Page 248 of 570
247 Controls in detail
3-zone automatic climate control*
Setting the temperature
Make sure the front automatic climate
control is switched on (
page 236).
Press button> (page 234).
The indicator lamp on the button
comes on.
In displaye (
page 234), you will see
the >symbol followed by
MODE.
Set the desired temperature for the
rear passenger compartment using
temperature control 9 (
page 234).
After approximately 3 seconds after
the last adjustment, the display switch-
es back to its standard display and the
indicator lamp on button> goes
out.Adjusting air distribution
Use the air distribution controls3 or5
to adjust the air distribution for the rear
passenger compartment.
The symbols on the controls represent the
following functions:Adjusting manually
Press the desired air distribution con-
trol.
The indicator lamp on button U
goes out.
Adjusting automatically
Press buttonU.
The indicator lamp on the button
comes on. The air distribution is ad-
justed automatically.
iYou can also press the>button once
more to switch back to the standard display.
SymbolFunction
ZDirects air to the center air
vents
YDirects air to the footwells and
the side air vents
Page 268 of 570
267 Controls in detail
Driving systems
1Setting current or higher speed
Adjustment in 1 mph increments (to
the resistance point) or 5 mph
increments (past the resistance point)
(Canada: 1 km/h or 10 km/h)
2Setting current or lower speed
Adjustment in 1 mph increments (to
the resistance point) or 5 mph
increments (past the resistance point)
(Canada: 1 km/h or 10 km/h)
3Canceling cruise control
4Resuming to last set speedActivating cruise control
You can activate the cruise control when
the vehicle speed is above
20 mph (30 km/h).
In the following cases you cannot activate
the cruise control:
when you brake
when you have set the parking brake
when the automatic transmission is set
to positionP, R, or N
if the ESP® is switched off
if the ESP® has switched off due to a
malfunction
Warning!G
The cruise control brakes automatically so
that the set speed is not exceeded. The
brake pedal depresses automatically when
the cruise control engages the brakes.
Keep driver’s foot area clear at all times,
including the area under the brake pedal.
Objects stored in this area may impair pedal
movement which could interfere with the
braking ability of the cruise control system.
Do not place your foot under the brake pedal
– your foot could become caught.
Keep in mind that the cruise control is a
convenience system designed to assist the
driver during vehicle operation. The driver is
and must always remain responsible for
the vehicle’s speed and for safe brake
operation.
iThe vehicle speed displayed in the speedo-
meter can briefly vary from the speed setting for
the cruise control system.
Page 269 of 570
268 Controls in detail
Driving systems
Setting current speed
Accelerate or decelerate to the desired
speed.
Briefly lift the cruise control lever in
direction of arrow1 or depress in
direction of arrow2 (
page 267).
The current speed is set.
Remove your foot from the accelerator
pedal.
The cruise control is activated.
The currently set speed appears in the
multifunction display for approximately
5 seconds.Canceling cruise control
There are several ways to cancel the cruise
control:
Step on the brake pedal.
The cruise control is canceled. The last
set speed is stored for later use.
or
Briefly push the cruise control lever in
direction of arrow3 (
page 267).
The cruise control is canceled. The last
set speed is stored for later use.
iOn uphill grades, the cruise control may not
be able to maintain the set speed. Once the
grade eases, the set speed will be resumed.
On downhill grades, the cruise control maintains
the set speed by braking with the vehicle’s
braking system. In addition, on longer downhill
grades the automatic transmission will down-
shift automatically.
iThe last stored speed is canceled when you
turn off the engine.
iThe cruise control switches off
automatically when
you step on the brake pedal
you depress the parking brake pedal
The cruise control switches off automatically and
an acoustic warning will sound when
the vehicle speed is below 20 mph
(30 km/h)
the ESP® is in operation
the ESP® is switched off with the ESP®
switch (
page 104)
the ESP® has switched off due to a
malfunction (
page 441)
you set the automatic transmission toN
while driving
Observe additional messages in the
multifunction display that may appear.
Page 272 of 570
271 Controls in detail
Driving systems
Briefly press the cruise control lever
down past the resistance point in
direction of arrow2.
Release the cruise control lever.
The vehicle set speed decreases in
increments of 5 mph
(Canada: 10 km/h).Setting to last stored speed
(“Resume” function)
Briefly pull the cruise control lever in
direction of arrow4 (
page 267).
The cruise control resumes to the last
set speed or, if no speed is stored, it
will set and store the current speed.
Remove your foot from the accelerator
pedal.
The last set speed appears in the multi-
function display for approximately
5 seconds.
Distronic*
When activated, the Distronic adaptive
cruise control system increases the driving
convenience afforded by the cruise control
while traveling on expressways and other
major roadways.
If the Distronic distance sensor detects
a slower moving vehicle directly ahead,
your vehicle speed will be reduced so
that you follow that vehicle at your
preset following distance.
If there is no vehicle directly ahead of
you, Distronic will function in the same
way as standard cruise control
(
page 266).
iThe new speed is set and the vehicle will
decelerate. Keep in mind that it may take a brief
moment until the vehicle has reached the set
speed.
Warning!G
The set speed stored in memory should only
be set again if prevailing road conditions
permit. Possible acceleration or decelera-
tion differences arising from returning to the
preset speed could cause an accident
and/or serious injury to you and others.
Page 275 of 570
274 Controls in detail
Driving systems
Distronic displays in the speedometer
dial
1Set speed
If Distronic is activated, one or two cruise
control speed segments come on around
the set speed.1Set speed
2Cruise control speed segments
3Speed of the vehicle ahead
If Distronic detects a vehicle directly
ahead, the cruise control speed
segments2, which represents the differ-
ence from the speed of the preceding
vehicle3 to the driver’s selected set
speed1, appear in the speedometer.iUSA only:
This device has been approved by the FCC as a
“Vehicular Radar System”. The radar sensor is
intended for use in an automotive radar system
only. Removal, tampering, or altering of the de-
vice will void any warranties, and is not permitted
by the FCC. Do not tamper with, alter, or use in
any non-approved way.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
iCanada only:
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation of the device.
Removal, tampering, or altering of the device will
void any warranties, and is not permitted. Do not
tamper with, alter, or use in any non-approved
way.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
iThe vehicle speed displayed on the speed-
ometer can briefly vary from the speed setting
on the Distronic system.
Page 277 of 570
276 Controls in detail
Driving systems
Distronic menu in the control system
Use the
DISTRONIC menu to display the
current settings for your Distronic system.
The information shown in the multifunction
display depends on whether the Distronic
system is activated or deactivated.
Press buttonè orÿ repeatedly
until you see one of the following two
displays in the multifunction display.Distronic activated
When you turn Distronic on, you will see
the set speed in the multifunction display
for about 5 seconds. When Distronic is
activated, the following display appears in
the multifunction display.
1Distronic activated
2Set vehicle speedDistronic deactivated
When Distronic is deactivated, you will see
the standard Distronic display in the multi-
function display.
1Preceding vehicle, if detected
2Actual distance to the preceding
vehicle
3Preset distance threshold to the
preceding vehicle
4Your vehicle
Cruise control lever
The Distronic system is operated by means
of the cruise control lever.
The cruise control lever is the uppermost
lever on the left-hand side of the steering
column.
iFor activating or deactivating the Distronic
system, see “Activating Distronic” (
page 277)
or see “Deactivating Distronic” (
page 280).
For activating or deactivating the Distance warn-
ing function, see “Distance warning function*”
(
page 191).
Page 278 of 570
277 Controls in detail
Driving systems
1Setting current or higher speed
Adjustment in 1 mph increments (to
the resistance point) or 5 mph
increments (past the resistance point)
(Canada: 1 km/h or 10 km/h)
2Setting current or lower speed
Adjustment in 1 mph increments (to
the resistance point) or 5 mph
increments (past the resistance point)
(Canada: 1 km/h or 10 km/h)
3Deactivating Distronic
4Activating Distronic or resuming to last
set speedActivating Distronic
You can activate Distronic when the vehi-
cle speed is between 20 mph (30 km/h)
and 110 mph (180 km/h).
When Distronic is activated the multifunc-
tion display will show a message such as
DISTRONIC 55 mph.
If Distronic has not been activated after
pressing the cruise control lever, you will
see the message
DISTRONIC Off in the
multifunction display.
In the following cases you cannot activate
Distronic:
up to 2 minutes after starting the
engine
when you brake
when you have set the parking brake
when the automatic transmission is set
to positionP, R, or N
if the ESP® is switched off
if the ESP® has switched off due to a
malfunctionSetting the current speed
Accelerate or decelerate to the desired
speed.
Briefly lift the cruise control lever in
direction of arrow1 or depress in
direction of arrow2 (
page 276).
Distronic is activated and the current
speed is set.
Remove your foot from the accelerator
pedal.
iIf you do not take your foot off of the accel-
erator pedal but continue to accelerate past the
set speed, the following message will appear in
the multifunction display:
DISTRONIC Override
The distance to a slower moving vehicle in front
of you will not be set. Your vehicle speed will
then be determined only by the accelerator
pedal position.
Page 281 of 570
280 Controls in detail
Driving systems
Setting to last stored speed
(“Resume” function)
Briefly pull the cruise control lever in
direction of arrow4 (
page 276).
The Distronic resumes to the last set
speed.
Remove your foot from the accelerator
pedal.
The last set speed or, if no speed is stored,
the current set speed appears in the
multifunction display for approximately
5 seconds.Deactivating Distronic
There are several ways to deactivate the
Distronic system:
Step on the brake pedal.
or
Briefly tip the cruise control lever in
direction of arrow3 (
page 276).
Distronic will be deactivated. The last set
speed will be stored in memory.
Warning!G
The set speed stored in memory should only
be set again if prevailing road conditions
permit. Possible acceleration or decelera-
tion differences arising from returning to the
preset speed could cause an accident
and/or serious injury to you and others.
iThe following message appears in the multi-
function display for approximately 5 seconds:
DISTRONIC Off.
The last stored set speed is deleted when the
engine is turned off.
iThe Distronic switches off automatically
when
you step on the brake pedal
you depress the parking brake pedal
In this case, the Distronic speed segments in the
speedometer (
page 274) will go out.
the vehicle speed is below 20 mph
(30 km/h)
the ESP® is in operation
the ESP® is switched off with the ESP®
switch (
page 104)
the ESP® has switched off due to a
malfunction (
page 441)
you set the automatic transmission toN
while driving
The Distronic speed segments in the speedome-
ter (
page 274) will go out and an acoustic
warning will sound.