lock MERCEDES-BENZ S CLASS 2003 Owners Manual

327 Practical hints
Unlocking/locking in an emergency
Unlocking the trunk
If you are unable to unlock the trunk with
the SmartKey, open the trunk with the me-
chanical key as follows:Trunk lock
Insert the mechanical key into the
trunk lid lock.

Turn the mechanical key counterclock-
wise to position1.

Press button2.
The trunk lid swings open.
Locking the vehicle
If you are unable to lock the vehicle with
the SmartKey or the KEYLESS-GO* card,
lock it with the mechanical key as follows:
Close the passenger doors and the
trunk lid.

Press the central locking switch in the
center console (
page 103).

Check to see whether the locking knob
on the passenger door is still visible. If
necessary push it down manually.

Lock the driver’s door with the me-
chanical key.

Lock the trunk lid if necessary with the
mechanical key (
page 326).
!The trunk lid swings open upwards au-
tomatically. Always make sure that
there is sufficient overhead clearance.
A minimum height clearance of 6 ft.
(1.85 m) is required to open the trunk
lid.iUnlocking your vehicle with the me-
chanical key will trigger the anti-theft
alarm system. To cancel the alarm, do
one of the following:

Press button
Œ
or
‹
on the
SmartKey.


Insert the SmartKey in the starter
switch.


If KEYLESS-GO* card present,
press the start/stop button
(page 33).

328 Practical hintsUnlocking/locking in an emergencyChanging batteries
If the batteries in the SmartKey or the
KEYLESS-GO* card are discharged, the ve-
hicle can no longer be locked or unlocked.
It is recommended to have the batteries re-
placed at an authorized Mercedes-Benz
Center.Batteries contain materials that can harm
the environment if disposed of improperly.
Recycling of batteries is the preferred
method of disposal. Many states require
sellers of batteries to accept old batteries
for recycling.SmartKey
1Mechanical key
2Battery compartment
Replacement batteries: Lithium, type
CR 2025 or equivalent.

Remove mechanical key1.

Insert the mechanical key in side open-
ing and push gray slide.
The battery compartment is unlatched.

Pull the battery compartment out of the
SmartKey housing in direction of ar-
row.

Remove the batteries.
Warning!
G
Keep the batteries out of reach of children.
If a battery is swallowed, seek medical help
immediately.
iWhen changing batteries, always re-
place both batteries.
The required replacement batteries are
available at any authorized
Mercedes-Benz Center.

329 Practical hints
Unlocking/locking in an emergency
3Battery
4Contact spring
Using a lint-free cloth, insert new bat-
teries under the contact spring with the
plus (+) side facing up.

Return battery compartment into hous-
ing until it locks into place.KEYLESS-GO* card
1Battery cover
Replacement batteries: Lithium, type
CR 2025 or equivalent.

Pry open cover 1 (e.g. by using a nar-
row blade screwdriver).

Remove the batteries.

Install new batteries as indicated by
the “+” and “-” markings in the
KEYLESS-GO card.

Replace battery cover 1.
Fuel filler flap
In an emergency, the fuel filler flap can be
opened from the trunk. The release lever is
located on the right-hand side in the trunk.
1Release knob
Open the trunk with the mechanical
key (
page 326).

Remove the trim inside the trunk on the
right-hand side.

Pull release lever1 in the direction of
the arrow.
The fuel filler flap can be opened.

330 Practical hintsOpening/closing in an emergency
Opening/closing in an emergencySliding/pop-up roof
The driving mechanism for the slid-
ing/pop-up roof is located behind the lens
of the interior overhead light.
You can open or close the sliding/pop-up
roof manually should an electrical malfunc-
tion occur.
1Lens

Pry off lens1 using a srewdriver.

Turn the SmartKey in the starter switch
to position1 or2.

Remove the crank from the operator’s
manual pouch.
2Crank

Insert crank2 through hole.

Turn crank2 clockwise to:

close slide roof


raise roof at the rear

Turn crank2 counterclockwise to:

open slide roof


lower roof at the rear
The sliding/pop-up must be resynchro-
nized after being operated manually
(
page 195).

334 Practical hintsReplacing bulbs
Insert the new bulb in the socket so
that the base is in the recess on the
lower left.

Attach the retaining springs.

Insert connector7 into the bulb.

Press cover3 onto the housing until
the tab engages.Replacing high beam bulbs

Switch off the lights.

Open the hood (
page 263).

Press the tab on cover2 and remove
cover.

Pull connector 6 off of the bulb.

Apply pressure on the bulb contacts
from above until the bulb releases from
the retaining springs.

Remove bulb.

Insert the new bulb in the socket with
the marking facing upward.

Press the bulb upward on the contacts
until it engages in the retaining springs.

Insert connector6 onto the bulb.

Press cover2 onto the housing until
the tab engages.Front turn signal lamp bulb

Switch off the lights.

Open the hood (
page 263).

Twist bulb socket8 counterclockwise
and pull out.

Gently push bulb into socket, turn
counterclockwise and remove.

Insert new bulb in socket, push in and
twist clockwise.

Reinstall bulb socket in lamp and twist
clockwise until it engages.


335 Practical hints
Replacing bulbs
Parking and standing lamp bulb
Switch off the lights.

Open the hood (
page 263).

Press the tab on cover2 and remove
cover.

Pull out the bulb socket5 with the
bulb.

Pull the bulb out of the bulb socket.

Insert a new bulb in the socket.

Reinstall the bulb socket.

Press cover2 onto the housing until
the tab engages.Side marker lamp bulb

Switch off the lights.

Carefully slide lamp towards rear.

Remove front end first.

Twist bulb socket counterclockwise
and pull out.

Pull bulb out of the bulb socket.

Insert new bulb in socket.

Reinstall bulb socket, push in and twist
clockwise.

To reinstall lamp, set rear end in
bumper and let front end snap into
place.

336 Practical hintsReplacing bulbsReplacing bulbs for rear lamps
Tail lamp assemblies
1Turn signal lamp (white socket)
2Tail, parking, standing, and side marker
lamp (red socket)
3Tail lamp, rear fog lamp (red socket)
4Backup lamp (black socket)

Switch off the lights.

Open trunk.

Turn the catch, and move the trim to
the side.

Turn bulb socket counterclockwise and
pull out.

Gently twist bulb counterclockwise and
pull out of bulb holder.

Insert new bulb into the holder and turn
it clockwise.

Reinstall bulb socket.
The bulb socket should audibly click.

Replace trim and secure with lock. License plate lamp
1Screws

Switch off the lights.

Loosen both screws1 and remove
lamp.

Replace the tubular lamp and reinstall
it.

Retighten the screws.

337 Practical hints
Replacing wiper blades
Replacing wiper blades
Removing
Turn SmartKey in starter switch
position1.

Turn combination switch to wiper
settingII (
page 47).

With wiper arm in vertical position (see
above), turn SmartKey in starter switch
to position0.

Fold the wiper arm forward.
You should hear it snap into place.

Turn the wiper blade at a right angle to
wiper arm (arrow 1).
1Lock
2Unlock

Pull the tab in the direction of arrow2
and remove windshield wiper.
!To avoid damage to the hood, the wiper
arms should only be folded forward
when in the vertical position.
Warning!
G
For safety reasons, remove SmartKey from
starter switch before replacing a wiper
blade, otherwise the motor could suddenly
turn on and cause injury.

339 Practical hints
Flat tire
Flat tire
Preparing the vehicle
Park the vehicle as far as possible from
moving traffic on a hard surface.

Turn on the hazard warning flashers.

Engage the steering wheel lock in the
straight-ahead position and set the
parking brake.

Move the selector lever toP.

Have any passenger exit the vehicle at
a safe distance from the roadway.
Mounting the spare wheel Preparing the vehicle

Take vehicle tool kit tray and vehicle
jack out of trunk .

Take the spare wheel out of wheel well
(page 322).
Lifting the vehicle

Prevent the vehicle from rolling away
by blocking wheels with wheel chocks
(not included) or other sizable objects.
When changing wheel on a level surface:

Place one chock in front of and one be-
hind the wheel that is diagonally oppo-
site to the wheel being changed.
When changing wheel on a hill:

Place chocks behind the downhill sides
of both wheels of the axle not being
worked on.
Warning!
G
Never operate the vehicle with more than
one spare wheel mounted.
The spare wheel rim is for temporary use
only. Use for over a total of 12000 miles
(20000 km) (aggregate of all uses) may
cause wheel rim failure leading to an acci-
dent and possible injuries.
The spare wheel should only be used tempo-
rarily and replaced with a regular road wheel
as quickly as possible.
S 55 AMG and Sport Package* only:
The spare wheel is for temporary use only.
When driving with spare wheel mounted, en-
sure proper tire pressure and do not exceed
vehicle speed of 50 mph (80 km/h).
The dimensions of the spare wheel are dif-
ferent from those of the road wheels. As a
result, the vehicle handling characteristics
change when driving with a mounted spare
wheel. Adapt your driving style accordingly.


340 Practical hintsFlat tire

Take the two-piece wheel wrench out
of the vehicle tool kit tray. Assemble
wheel wrench.

On wheel to be changed, loosen but do
not yet remove the wheel bolts (ap-
proximately one full turn with wrench).
The tube openings are located directly be-
hind the front wheel housings and in front
of the rear wheel housings.1Jack support tube cover

Move cover1 toward rear by pressing
at point indicated by arrow.

Remove cover1 carefully to avoid
damage to the locking tabs.
Warning!
G
The jack is designed exclusively for jacking
up the vehicle at the jack tubes built both
sides of the vehicle. To help avoid personal
injury, use the jack only to lift the vehicle
during a wheel change. Never get beneath
the vehicle while it is supported by the jack.
Keep hands and feet away from the area un-
der the lifted vehicle. Always firmly set park-
ing brake and block wheels before raising
vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use, es-
pecially on hills. Always try to use the jack
on level surface. Make sure that the jack
arm is fully inserted in the jack tube. Always
lower the vehicle onto sufficient capacity
jackstands before working under the vehi-
cle.