Radio MERCEDES-BENZ S-Class 2004 W220 Comand Manual

21 At a glance
Menu system
The main area 2 shows messages and
settings.
You can change the settings by operating
the system.
The status bar 3 is divided into three
areas.
Left side:
The current operating mode is indicated. In
this example: Radio
Center:
The status of the current operating mode
or other selectable functions are indicated.
In this example:
FM
= current waveband

9
= memory location of station,
e.g. “9”Right side:
General status information is indicated
independent of the operating mode.
In this example:

Ready
= Telephone* is ready for
operation

= Reception strength of the
mobile phone
Menu functions and submenus
Using the soft keys, functions can be
switched ON or OFF, or submenus can be
called up.Example: Radio main menu:

The
FM/AM
soft key switches between
FM and AM band.

The
Scan
soft key starts/stops the
channel scan.
In some situations, soft keys may not have
any function and are not operational. A
soft key without function appears shaded
out.

23 At a glance
Quick reference COMAND
Switching on
Turn the key in the steering column
lock to position 1 or 2.
or

Press e.
In both cases, the system will activate
the operating mode which was active
when the system was switched off.Switching off

Turn the key in the steering column
lock to position 0 and pull the key out.
or

Press e.
The volume is adjusted jointly for the
telephone*, the navigation system and the
Voice control system.
The volume setting applies to other
operating modes as well: radio, tape, CD,
CD changer*, MP3-CD and DVD.
When you adjust the volume, the system
will automatically store the setting for the
current operating mode. The volume for
the navigation announcements can only be
changed while an announcement is being
made.
iYou have the following options to
control the system:
at the COMAND

at the multifunction steering wheel
(refer to vehicle Operator's Manual)

using the Voice control system*
(refer to separate operating
instructions for further information)
This Operator’s Manual describes the
control at the COMAND.
Unless otherwise indicated, the
descriptions and illustrations refer to
the COMAND.
Switching the COMAND control unit
on and offiIf the key is not in the steering lock in
position 1 or 2, the system will
automatically stop after around 30
minutes. A warning is displayed prior to
the system switching off.
Volume

Quick reference COMAND

25 At a glance
Quick reference COMAND
Common balance and fader settings apply
to the following sytems:
Radio operation

Tape operation

CD operation (single CD)

CD changer* operation

MP3-CD operation

DVD operation
Different balance and fader settings can be
set for navigation and telephone*.The balance/fader settings for navigation
announcements are described at “Audio
settings for the navigation
announcements” (
page 117).
When you make balance or fader settings,
the system will automatically save the
settings for the current operating mode
and others.
Setting balance and fader
In radio, tape, CD, CDC*, MP3-CD or DVD
operation:

Press the
Bal/Fad
soft key.
Cross-hairs are displayed. The
horizontal line indicates the balance
setting. The vertical line indicates the
fader setting. You can now make
balance and fader settings.
Balance and fader

26 At a glanceQuick reference COMAND
Press H or h.
Move the cross-hairs horizontally and
adjust the balance.
or

Press g or G.
Move the cross-hairs vertically and
adjust the fader.

Press E or the
Back
soft key.
or

Wait until the display changes.
The new setting is saved.Different bass and treble settings are
possible for the following operating
modes:

Radio operation (FM and AM band)

Tape operation

CD operation (single CD)

CD changer* operation

MP3-CD operation

DVD operation

Navigation operation
The Bass/Treble settings for navigation
announcements are described at “Audio
settings for the navigation
announcements” (
page 117).When you adjust Bass or Treble, the
system will automatically save the settings
for the current operating mode.
Activating the Bass or Treble menu
In radio, tape, CD, CDC*, MP3-CD or DVD
operation:

Press the Bass or Treble soft key.
The Bass or Treble menu will appear.
You can now make bass or treble
settings (
page 27).
iUse F and f to move the
cross-hairs diagonally.
Bass and Treble

27 At a glance
Quick reference COMAND
Bass and Treble Control
Activate the Bass or Treble menu
(page 26).

Press H or h.
Bass or Treble is adjusted.

Press E or the
Back
soft key.
or

Wait until the display changes.
The new setting is saved.If your vehicle is provided with the sound
system*, the sound functions* will be
available for the following operating
modes.

Radio operation

Tape operation

CD operation

MP3-CD operation
The following sound functions* are
available:

Default:COMAND set the sound linear for the
center of the vehicle.

Front optimized:COMAND set the sound linear for the
front of the vehicle.

Rear optimized:COMAND set the sound linear for the
rear of the vehicle.

Speech optimized:Playback optimised for language
comprehensibility.

Surround:Surround playback (not for radio).
You can use different sound functions* for
the modes mentioned above.
Example:
For radio operation the function
Default
, for CD operation the function
Surround
.
Sound functions*

28 At a glanceQuick reference COMANDActivating the sound functions*
In radio, tape, single CD or CD changer*
operation:
Activate the main menu for the
respective operating mode
(page 20).

Press the
Sound
soft key.
The Sound menu appears.

Press g or G to select the desired
function.

Press E.
The function is activated.
iSurround sound offers a sound quality
superior to conventional stereo sound.
If the radio reception is poor, the
system should be switched back to
standard stereo playback. Switching
back to standard stereo playback may
improve reception quality.

29 Audio
Radio operation
Tape operation
CD operation
MP3-CD operation
DVD operation

30 AudioRadio operationIn chapter “Audio” you will find detailed
information regarding
radio operation

tape operation

CD operation

MP3-CD operation

DVD operation
If you have not done so already, please fa-
miliarize yourself with these functions by
reading chapter “At a glance”.

Press A.
Audio menu
If an audio submenu is displayed, press
the
Back
soft key until the Audio menu
is displayed.
or

Press A again.

In the Audio menu, press the soft key
for the desired audio source.
Switching On

In the Audio menu, press the
Off
soft
key.
The system mutes the active audio
source.
The
Off
soft key is deactivated.
or

Press J.

The system mutes the active audio
source.
Opening the Audio menu
Selecting an audio sourceMuting

Radio operation

31 Audio
Radio operation
Switching off
In the Audio menu, press the
Radio

soft key.
or

Press J again.

In the Audio menu, press the
Radio

soft key.
The Radio main menu will appear.
Radio main menu1Soft key assignment
2Main area
3Status barThe station last tuned in is received.
Switching back to Audio menu

Press the
Back
soft key.
Switching the radio operation on
iThe
Sound
soft key appears if the
COMAND is provided with sound
functions* (page 27).

32 AudioRadio operationYou can select between FM-, AM- and WB-
Band.
AM Band
In the FM Radio main menu, press soft
key
FM/AM
until “AM” is displayed in
the status bar.
The AM station last tuned to will begin
to play. The frequency will appear in
the display.Weather Band WB

In the FM or AM Radio main menu,
press the
WB
soft key.
An automatic scan is starting and the
COMAND plays and displays the first
strong WB station.Switching back to FM or AM band

Press the
FM/AM
soft key.
The station last tuned to will begin to
play.
Switching back to Audio menu

Press the
Back
soft key.
Changing the Radio band
Frequency band
Frequency range
FM
AM
87.7 - 107.9 FM
530 - 1710 AM
iWith the number keys 1 - 7 it is pos-
sible to choose a channel.