remote control MERCEDES-BENZ S CLASS 2005 User Guide

166 Controls in detailControl systemSetting locator lighting
During darkness, the following lamps will
come on when the exterior lamp switch is
in position U, the locator lighting fea-
ture is activated, and the vehicle is un-
locked by remote control:

Parking lamps


Tail lamps


License plate lamps


Front fog lamps
To activate locator lighting:

Make sure the function
LOCATOR
LIGHTING
is set.

Turn the exterior lamp switch to
positionU.
The locator lighting switches off when the
driver’s door is opened. It switches off au-
tomatically after a period of approximately
40 seconds.

Move the selection marker with
theæ orç button to the
LIGHT-
ING
submenu.

Press buttonj ork repeatedly
until you see this message in the multi-
function display:
LOCATOR LIGHTING
.
The selection marker is on the current
setting.

Pressæ orç to select the de-
sired setting.
The locator lighting will be switched
ON
or
OFF
.Setting night security illumination
(Exterior lamps delayed switch-off)
Use the
HEADLAMPS DELAYED SWITCH-OFF

function to set whether and for how long
you would like the exterior lamps to illumi-
nate during darkness after all doors are
closed. When the delayed switch-off fea-
ture is activated and the exterior lamp
switch is in position U before the en-
gine is turned off, the following lamps will
remain lit after you remove the SmartKey
from the starter switch:


Parking lamps


Tail lamps


License plate lamps


Front fog lamps

255 Controls in detail
Useful features
Tele Aid
The Tele Aid system
(Tele
matic A
larm I
dentification on D
e-
mand)
The Tele Aid system consists of three
types of response:


automatic and manual emergency


roadside assistance, and


informationThe Tele Aid system is operational provid-
ing that the vehicle’s battery is charged,
properly connected, not damaged and cel-
lular and GPS coverage is available.
The speaker volume of a Tele Aid call can
be adjusted when using the volume control
on the multifunction steering wheel. To
raise, press buttonæ and to lower,
press buttonç or use the volume knob
on your COMAND headunit.

To activate, press the SOS button, the
Roadside Assistance button• or
the Information button¡, depend-
ing on the type of response required.Shortly after the completion of your Tele
Aid acquaintance call, you will receive a
user ID and password. By visiting
www.mbusa.com and selecting “Tele Aid”
(USA only), you will have access to account
information, remote door unlock and
more.
!The initial activation of the Tele Aid sys-
tem may only be performed by com-
pleting the subscriber agreement and
placing an acquaintance call using the
Information button¡. Failure to
complete either of these steps will re-
sult in a system that is not activated.
If you have any questions regarding ac-
tivation, please call the Response Cen-
ter at 1-800-756-9018 (in the USA) or
1-888-923-8367 (in Canada).
iThe SOS button is located above the in-
terior rear view mirror.
The Roadside Assistance button•
and the Information button¡ are
located below the center armrest cov-
er.
iThe Tele Aid system utilizes the cellular
network for communication and the
GPS (Global Positioning System) satel-
lites for vehicle location. If either of
these signals are unavailable, the
Tele Aid system may not function and if
this occurs, assistance must be sum-
moned by other means.

262 Controls in detailUseful features
Remote door unlock
In case you have locked your vehicle unin-
tentionally (e.g. SmartKey inside vehicle),
and the reserve SmartKey is not handy:
Contact the Mercedes-Benz Response
Center at 1-800-756-9018 (in the USA)
or 1-888-923-8367 (in Canada).
You will be asked to provide your pass-
word which you provided when you
completed the subscriber agreement.

Then return to your vehicle and press
the trunk lid button for a minimum of
20 seconds until the SOS button is
flashing.
The message
CALL CONNECTED
ap-
pears in the multifunction display.
As an alternative, you may unlock the vehi-
cle via Internet using the ID and password
sent to you shortly after the completion of
your acquaintance call.
The Response Center will then unlock your
vehicle with the remote door unlocking
feature.
iWhen a Tele Aid call has been initiated,
the audio system or the COMAND*
system audio is muted and the
selected mode (radio or CD) pauses.
The optional cellular phone (if installed)
switches off. If you must use this
phone, the vehicle must be parked.
Disconnect the coiled cord and place
the call. The COMAND* navigation
system (if engaged) will continue to
run. The display in the instrument
cluster is available for use, and spoken
commands are only available by press-
ing the RPT button on the COMAND*
unit. A pop-up window will appear in
the COMAND* display to indicate that
a Tele Aid call is in progress.
iThe remote door unlock feature is avail-
able if the relevant cellular phone net-
work is available.
The SOS button will flash and the mes-
sage
CALL CONNECTED
will appear in
the multifunction display to indicate re-
ceipt of the door unlock command.
Once the vehicle is unlocked, a Re-
sponse Center specialist will attempt
to establish voice contact with the ve-
hicle occupants.
If the trunk lid button was pressed for
more than 20 seconds before door un-
lock authorization was received by the
Response Center, you must wait
15 minutes before pressing the trunk
lid button again.

264 Controls in detailUseful featuresGarage door opener
The built-in remote control is capable of
operating up to three separately controlled
devices, for example garage door openers,
gate openers, or other devices compatible
with HomeLink
® or some other systems.
You can program the signal transmitter
buttons.
Remote control integrated into the interior
rear view mirror1Indicator lamp
2 3 4Signal transmitter button
5Hand-held transmitter button
6Hand-held remote control trans-
mitter (not part of the vehicle
equipment)
Warning!
G
Before programming the integrated remote
control to a garage door opener or gate op-
erator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage.
When programming a garage door opener,
the door moves up or down. When program-
ming a gate operator, the gate opens or
closes.
Do not use the integrated remote control
with any garage door opener that lacks safe-
ty stop and reverse features as required by
U.S. federal safety standards (this includes
any garage door opener model manufac-
tured before April 1, 1982). A garage door
that cannot detect an object - signaling the
door to stop and reverse - does not meet
current U.S. federal safety standards.

266 Controls in detailUseful featuresProgramming or reprogramming the in-
tegrated remote control
Step 1:
Switch on ignition (
page 34).
Step 2:

If you have previously programmed an
integrated signal transmitter button
and wish to retain its programming,
proceed to step 3. Otherwise, press
and hold the two outer signal transmit-
ter buttons2 and 4 and release
them only when the indicator lamp1
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory. If you later wish to program a
second and/or third hand-held trans-
mitter to the remaining two signal
transmitter buttons, do not repeat this
step and begin directly with step 3.Step 3:

Hold the end of the hand-held remote
control transmitter6 of the device
you wish to train approximately 2 to
5 in (5 to 12 cm) away from the surface
of the integrated remote control locat-
ed on the interior rear view mirror,
keeping the indicator lamp1 in view.
Step 4:

Using both hands, simultaneously
press the hand-held transmitter
button5 and the desired integrated
signal transmitter button (2, 3
or4). Do not release the buttons until
completing step 5.
The indicator lamp1 on the integrat-
ed remote control will flash, first slowly
and then rapidly.Step 5:

When the indicator lamp 1 flashes
rapidly, release both buttons.
Step 6:

Press and hold the just-trained inte-
grated signal transmitter button and
observe the indicator lamp1.
If the indicator lamp1 stays on con-
stantly, programming is complete and
your device should activate when the
integrated signal transmitter button is
pressed and released.iThe indicator lamp1 flashes the first
time the signal transmitter button is
programmed. If this button has already
been programmed, the indicator lamp
will only start flashing after 20 sec-
onds.

268 Controls in detailUseful featuresStep 12:
Confirm the garage door operation by
pressing the programmed integrated
signal transmitter button (2, 3
or4).
Step 13:

To program the remaining two buttons,
repeat the steps above starting with
step 3.Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the inte-
grated signal transmitter to pick up the sig-
nal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having dif-
ficulties programming a gate operator (re-
gardless of where you live) by using the
programming procedures, replace step 4
with the following:Step 4:

Continue to press and hold the inte-
grated signal transmitter button (2,
3 or4) while you press and re-press
(“cycle”) your hand-held remote con-
trol transmitter6 every two seconds
until the frequency signal has been
learned. Upon successful training, the
indicator lamp1 will flash slowly and
then rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete.


269 Controls in detail
Useful features
Operation of integrated remote control
Switch on ignition (
page 34).

Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.Erasing the integrated remote control
memory

Switch on ignition (
page 34).

Simultaneously hold down the signal
transmitter buttons 2and 4, for ap-
proximately 20 seconds, until the indi-
cator lamp1 flashes rapidly. Do not
hold for longer than 30 seconds.
The codes of all three channels are
erased.Reprogramming a single integrated sig-
nal transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:

Press and hold the desired signal trans-
mitter button (2, 3 or4). Do not re-
lease the button.

The indicator lamp1 will begin to
flash after 20 seconds. Without releas-
ing the integrated signal transmitter
button, proceed with programming
starting with step 3.
iIf you sell your vehicle, erase the codes
of all three channels.

451 Index
Driving systems 214
ABC 231
AIRMATIC 229
Airmatic 229
Cruise control 214
Distronic* 217
Driving safety systems 80
Parktronic system* 235
Vehicle level control 230, 232
E
Easy-entry/exit feature 114
Activating 170
Electrical fuses 411
Electrical system 427
Electrically folding exterior rear view
mirrors 188
Electronic Stability Program see ESP 82,
439
Emergency call system* 255
Emergency calls
Initiating an emergency call 257
With Tele Aid 256
Emergency operation (Limp Home
Mode) 185Emergency operations
Closing the power tilt/sliding
sunroof 386
Locking the vehicle 384
Opening the power tilt/sliding
sunroof 386
Remote door unlock 262
Unlocking the vehicle 383
Emergency tensioning device see
ETD 69, 439
Emission control 282
Emission control information label 418
Ending
A call (telephone) 154
Engine 420
Compartment 286
Message in display 340, 341
Starting 46
Starting with KEYLESS-GO* 47
Starting with the SmartKey 46
Turning off with the SmartKey or the
SmartKey with KEYLESS-GO* 57
Engine cleaning 332
Engine compartment 286
Fuse box in 413
Hood 286Engine malfunction indicator lamp 340,
341
Engine number 418, 439
Engine oil 287
Adding 291
Additives 431
Checking level 287
Consumption 287
Display messages 362
Filler neck 291
Messages in display 289, 362
Viscosity 439
Engine oil level see Oil level 285
Entry position
Messages in display 364
ESP 82, 439
Four wheel electronic traction system
with ESP 85
Switching off 83
Switching on 84
Synchronizing 352
Warning lamp 342, 343
ETD 439
Safety guidelines 64
ETD (Emergency tensioning device) 69
Exterior lamp switch 131

453 Index
G
Garage door opener 264
Erasing in remote control 269
Integrated remote control 266
Rolling code programming 267
Gasoline see Fuel 284
GAWR 322
Gear range 439
Automatic transmission 176
Limiting 176
Shifting into optimal 175
Gear range limit
Canceling 175
Gear selector lever
Cleaning 335
Position (Automatic
transmission) 177
Position (automatic
transmission) 173
Glasses
Storage compartment in front of
armrest 246Global
Locking 94
Unlocking 94
Global Positioning System (GPS) 439
Glove box 244
Closing 244
Locking 244
Opening 244
Unlocking 244
Gloves (vehicle tool kit) 380
Good visibility 186
GPS 255, 439
Gross Axle Weight Rating see GAWR
Gross Vehicle Weight Rating see GVWR
Gross Vehicle Weight see GVW
GVW 322
GVWR 323
H
Hand-held transmitter
Programming integrated remote
control 266
Hands-free microphone 29Hard plastic trim items
Cleaning 335
Hazard warning flasher 136
Switching off 136
Switching on 136
Head restraints 116
Headlamp cleaning system* 295
Headlamps
Automatic control 132
Bi-Xenon 437
Cleaning 332
Cleaning system* 186, 295
Refilling washer fluid 295
Switching off 57
Switching on 50
Headliner
Cleaning 335
Heated steering wheel* 253
Height adjustment
Head restraints 39
Steering wheel 40

454 IndexHeight adjustments
Vehicle level 230, 232
High beam 50
Replacing bulbs 390
High beam flasher 135
High beam headlamps
Messages in display 366
Switching on 135
High mounted brake lamp 390
Hood 286
Closing 287
Message in display 364
Opening 286
Hydroplaning 277
I
Identification labels 418
Emission control information
label 418
Vacuum line routing diagram
label 418
Ignition 34, 36
Switching on 34, 46, 47Immobilizer 86
Activating 86
Deactivating 86
Indicator lamps see Lamps, indicator and
warning
Individual seats* 117
Head restraint height 118
Infant and child restraint systems 71
Installing 75
LATCH child seat anchors 76
Information
About service and warranty 10
Button for Tele Aid* 260
Infrared reflecting windshield 270
Inside rear view mirror
Auto-dimming 186
Installing
Infant and child restraint systems 75
Towing eye bolt 410
Wiper blades 397Instrument cluster 24, 140, 439
Cleaning 335
Coolant temperature gauge 141
Illumination 140
Multifunction display 143
Outside temperature indicator 142
Selecting language 164
Integrated remote control
Canadian programming 268
Erasing memory 269
Hand-held transmitter 266
Operating 269
Rolling code programming 267
Interior illumination
Delayed switch-off 167
Interior lighting 137
Activating automatic control 137
Deactivating automatic control 137
Manual operation 137
Reading lamps in the front 138
Reading lamps in the rear 138
Interior rear view mirror
Adjusting 41